McAfee-Secured Website

Exam Code: JN0-106

Exam Name: Junos, Associate (JNCIA-Junos)

Certification Provider: Juniper

Corresponding Certification: JNCIA-Junos

100% Juniper JN0-106 Guaranteed Success With Testking Training Materials

Get Real JN0-106 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

98 Questions & Answers with Testing Engine

"Junos, Associate (JNCIA-Junos) Exam", also known as JN0-106 exam, is a Juniper certification exam.

Pass your tests with the always up-to-date JN0-106 Exam Engine. Your JN0-106 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Juniper JN0-106 Practice Test 90

Question 890

Within Routing Fundamentals, a Junos engineer proposes the following response: Configure a /32 host route for the single IPv4 destination. Which concept or operating procedure is best illustrated?

  1. IPv4 host route /32
  2. IPv4 supernet route
  3. Show active route detail
  4. IPv6 /128 loopback route

Explanation

Correct Answer

A:

An IPv4 /32 matches precisely one address and is more specific than broader subnets. This meets the stated need for ipv4 host route /32.

Incorrect Answers

B:

The ipv4 supernet route scenario has a different requirement: Two adjacent, correctly aligned /24 networks share a /23 prefix that covers exactly both. It does not directly meet the ipv4 host route /32 need in this question.

C:

The show active route detail scenario has a different requirement: Detailed route output reports attributes needed to understand the active route decision. It does not directly meet the ipv4 host route /32 need in this question.

D:

The ipv6 /128 loopback route scenario has a different requirement: An IPv6 /128 prefix uniquely identifies one IPv6 address without encompassing adjacent addresses. It does not directly meet the ipv4 host route /32 need in this question.

Question 891

A static route should target exactly one IPv4 address without covering its neighbors. The proposed response is: Configure a /32 host route for the single IPv4 destination. Which explanation most accurately supports this response?

  1. Two adjacent, correctly aligned /24 networks share a /23 prefix that covers exactly both.
  2. An IPv4 /32 matches precisely one address and is more specific than broader subnets.
  3. Detailed route output reports attributes needed to understand the active route decision.
  4. An IPv6 /128 prefix uniquely identifies one IPv6 address without encompassing adjacent addresses.

Explanation

Correct Answer

B:

An IPv4 /32 matches precisely one address and is more specific than broader subnets. This meets the stated need for ipv4 host route /32.

Incorrect Answers

A:

The ipv4 supernet route scenario has a different requirement: Two adjacent, correctly aligned /24 networks share a /23 prefix that covers exactly both. It does not directly meet the ipv4 host route /32 need in this question.

C:

The show active route detail scenario has a different requirement: Detailed route output reports attributes needed to understand the active route decision. It does not directly meet the ipv4 host route /32 need in this question.

D:

The ipv6 /128 loopback route scenario has a different requirement: An IPv6 /128 prefix uniquely identifies one IPv6 address without encompassing adjacent addresses. It does not directly meet the ipv4 host route /32 need in this question.

Question 892

Within Routing Fundamentals, a technician selects this approach: Configure a /32 host route for the single IPv4 destination. Which original requirement or fault would most directly justify it?

  1. A static route should target exactly one IPv4 address without covering its neighbors.
  2. A routing table needs to summarize adjacent 10.20.0.0/24 and 10.20.1.0/24 networks without including additional /24 blocks.
  3. A path is preferred but an engineer needs to see its protocol and next-hop attributes.
  4. A Junos loopback has address 2001:db8::10/128 and an administrator needs to identify its single-address route.

Explanation

Correct Answer

A:

An IPv4 /32 matches precisely one address and is more specific than broader subnets. This meets the stated need for ipv4 host route /32.

Incorrect Answers

B:

The ipv4 supernet route scenario has a different requirement: Two adjacent, correctly aligned /24 networks share a /23 prefix that covers exactly both. It does not directly meet the ipv4 host route /32 need in this question.

C:

The show active route detail scenario has a different requirement: Detailed route output reports attributes needed to understand the active route decision. It does not directly meet the ipv4 host route /32 need in this question.

D:

The ipv6 /128 loopback route scenario has a different requirement: An IPv6 /128 prefix uniquely identifies one IPv6 address without encompassing adjacent addresses. It does not directly meet the ipv4 host route /32 need in this question.

Question 893

A destination is reachable in routing instance BLUE but not through the default routing table. Which configuration or troubleshooting action most directly meets the need?

  1. Configure routing-options static route 0.0.0.0/0 with the reachable upstream next hop.
  2. Configure a /32 host route for the single IPv4 destination.
  3. Run ping with the appropriate routing-instance context where the CLI supports it.
  4. Restore the interface's operational state and recheck its connected route.

Explanation

Correct Answer

C:

Testing from the correct routing instance uses that instance's routing context rather than the default table. This meets the stated need for routing instance ping.

Incorrect Answers

A:

The ipv4 default static route scenario has a different requirement: The 0/0 default route matches all IPv4 destinations not covered by a more-specific active prefix. It does not directly meet the routing instance ping need in this question.

B:

The ipv4 host route /32 scenario has a different requirement: An IPv4 /32 matches precisely one address and is more specific than broader subnets. It does not directly meet the routing instance ping need in this question.

D:

The interface-down connected route scenario has a different requirement: Direct routes depend on their configured interfaces being operational and participating in routing. It does not directly meet the routing instance ping need in this question.

Question 894

Within Routing Fundamentals, a Junos engineer proposes the following response: Run ping with the appropriate routing-instance context where the CLI supports it. Which concept or operating procedure is best illustrated?

  1. Routing instance ping
  2. IPv4 default static route
  3. IPv4 host route /32
  4. Interface-down connected route

Explanation

Correct Answer

A:

Testing from the correct routing instance uses that instance's routing context rather than the default table. This meets the stated need for routing instance ping.

Incorrect Answers

B:

The ipv4 default static route scenario has a different requirement: The 0/0 default route matches all IPv4 destinations not covered by a more-specific active prefix. It does not directly meet the routing instance ping need in this question.

C:

The ipv4 host route /32 scenario has a different requirement: An IPv4 /32 matches precisely one address and is more specific than broader subnets. It does not directly meet the routing instance ping need in this question.

D:

The interface-down connected route scenario has a different requirement: Direct routes depend on their configured interfaces being operational and participating in routing. It does not directly meet the routing instance ping need in this question.

Question 895

A destination is reachable in routing instance BLUE but not through the default routing table. The proposed response is: Run ping with the appropriate routing-instance context where the CLI supports it. Which explanation most accurately supports this response?

  1. Testing from the correct routing instance uses that instance's routing context rather than the default table.
  2. The 0/0 default route matches all IPv4 destinations not covered by a more-specific active prefix.
  3. An IPv4 /32 matches precisely one address and is more specific than broader subnets.
  4. Direct routes depend on their configured interfaces being operational and participating in routing.

Explanation

Correct Answer

A:

Testing from the correct routing instance uses that instance's routing context rather than the default table. This meets the stated need for routing instance ping.

Incorrect Answers

B:

The ipv4 default static route scenario has a different requirement: The 0/0 default route matches all IPv4 destinations not covered by a more-specific active prefix. It does not directly meet the routing instance ping need in this question.

C:

The ipv4 host route /32 scenario has a different requirement: An IPv4 /32 matches precisely one address and is more specific than broader subnets. It does not directly meet the routing instance ping need in this question.

D:

The interface-down connected route scenario has a different requirement: Direct routes depend on their configured interfaces being operational and participating in routing. It does not directly meet the routing instance ping need in this question.

Question 896

Within Routing Fundamentals, a technician selects this approach: Run ping with the appropriate routing-instance context where the CLI supports it. Which original requirement or fault would most directly justify it?

  1. A destination is reachable in routing instance BLUE but not through the default routing table.
  2. A small office has one upstream gateway and needs a fallback for destinations not otherwise matched.
  3. A static route should target exactly one IPv4 address without covering its neighbors.
  4. A direct subnet disappears from the routing table after its only supporting interface goes down.

Explanation

Correct Answer

A:

Testing from the correct routing instance uses that instance's routing context rather than the default table. This meets the stated need for routing instance ping.

Incorrect Answers

B:

The ipv4 default static route scenario has a different requirement: The 0/0 default route matches all IPv4 destinations not covered by a more-specific active prefix. It does not directly meet the routing instance ping need in this question.

C:

The ipv4 host route /32 scenario has a different requirement: An IPv4 /32 matches precisely one address and is more specific than broader subnets. It does not directly meet the routing instance ping need in this question.

D:

The interface-down connected route scenario has a different requirement: Direct routes depend on their configured interfaces being operational and participating in routing. It does not directly meet the routing instance ping need in this question.

Question 897

A static route points to a next-hop router on an Ethernet LAN and requires local address resolution. Which configuration or troubleshooting action most directly meets the need?

  1. Use the forwarding table to determine actual packet forwarding rather than assuming every RIB candidate forwards.
  2. Inspect the BLUE.inet.0 table for that instance's IPv4 unicast routes.
  3. Ensure the next-hop IPv4 address is reachable on a directly connected link and ARP resolves.
  4. Prefer the eligible route with preference 5 when normal selection rules apply.

Explanation

Correct Answer

C:

The router must resolve a valid Ethernet adjacency before delivering the packet to the chosen next hop. This meets the stated need for ipv4 on-link next-hop.

Incorrect Answers

A:

The rib versus fib distinction scenario has a different requirement: The RIB can contain alternatives while the forwarding table holds usable forwarding decisions. It does not directly meet the ipv4 on-link next-hop need in this question.

B:

The named routing-instance rib scenario has a different requirement: Named Junos routing instances normally maintain their own tables such as BLUE.inet.0. It does not directly meet the ipv4 on-link next-hop need in this question.

D:

The lower route preference scenario has a different requirement: Junos route preference is a ranking in which a lower numeric preference is generally more preferred. It does not directly meet the ipv4 on-link next-hop need in this question.

Question 898

Within Routing Fundamentals, a Junos engineer proposes the following response: Ensure the next-hop IPv4 address is reachable on a directly connected link and ARP resolves. Which concept or operating procedure is best illustrated?

  1. RIB versus FIB distinction
  2. Named routing-instance RIB
  3. Lower route preference
  4. IPv4 on-link next-hop

Explanation

Correct Answer

D:

The router must resolve a valid Ethernet adjacency before delivering the packet to the chosen next hop. This meets the stated need for ipv4 on-link next-hop.

Incorrect Answers

A:

The rib versus fib distinction scenario has a different requirement: The RIB can contain alternatives while the forwarding table holds usable forwarding decisions. It does not directly meet the ipv4 on-link next-hop need in this question.

B:

The named routing-instance rib scenario has a different requirement: Named Junos routing instances normally maintain their own tables such as BLUE.inet.0. It does not directly meet the ipv4 on-link next-hop need in this question.

C:

The lower route preference scenario has a different requirement: Junos route preference is a ranking in which a lower numeric preference is generally more preferred. It does not directly meet the ipv4 on-link next-hop need in this question.

Question 899

A static route points to a next-hop router on an Ethernet LAN and requires local address resolution. The proposed response is: Ensure the next-hop IPv4 address is reachable on a directly connected link and ARP resolves. Which explanation most accurately supports this response?

  1. The RIB can contain alternatives while the forwarding table holds usable forwarding decisions.
  2. Named Junos routing instances normally maintain their own tables such as BLUE.inet.0.
  3. The router must resolve a valid Ethernet adjacency before delivering the packet to the chosen next hop.
  4. Junos route preference is a ranking in which a lower numeric preference is generally more preferred.

Explanation

Correct Answer

C:

The router must resolve a valid Ethernet adjacency before delivering the packet to the chosen next hop. This meets the stated need for ipv4 on-link next-hop.

Incorrect Answers

A:

The rib versus fib distinction scenario has a different requirement: The RIB can contain alternatives while the forwarding table holds usable forwarding decisions. It does not directly meet the ipv4 on-link next-hop need in this question.

B:

The named routing-instance rib scenario has a different requirement: Named Junos routing instances normally maintain their own tables such as BLUE.inet.0. It does not directly meet the ipv4 on-link next-hop need in this question.

D:

The lower route preference scenario has a different requirement: Junos route preference is a ranking in which a lower numeric preference is generally more preferred. It does not directly meet the ipv4 on-link next-hop need in this question.

Question 900

Within Routing Fundamentals, a technician selects this approach: Ensure the next-hop IPv4 address is reachable on a directly connected link and ARP resolves. Which original requirement or fault would most directly justify it?

  1. A static route points to a next-hop router on an Ethernet LAN and requires local address resolution.
  2. A device shows alternate route candidates, but a packet should follow an installed best-path next hop.
  3. A route belongs to routing instance BLUE rather than the default table.
  4. Two routes have the same destination prefix but one has Junos preference 5 and the other preference 10.

Explanation

Correct Answer

A:

The router must resolve a valid Ethernet adjacency before delivering the packet to the chosen next hop. This meets the stated need for ipv4 on-link next-hop.

Incorrect Answers

B:

The rib versus fib distinction scenario has a different requirement: The RIB can contain alternatives while the forwarding table holds usable forwarding decisions. It does not directly meet the ipv4 on-link next-hop need in this question.

C:

The named routing-instance rib scenario has a different requirement: Named Junos routing instances normally maintain their own tables such as BLUE.inet.0. It does not directly meet the ipv4 on-link next-hop need in this question.

D:

The lower route preference scenario has a different requirement: Junos route preference is a ranking in which a lower numeric preference is generally more preferred. It does not directly meet the ipv4 on-link next-hop need in this question.

Junos, Associate (JNCIA-Junos) (JN0-106) Practice Tests