McAfee-Secured Website

Exam Code: JN0-106

Exam Name: Junos, Associate (JNCIA-Junos)

Certification Provider: Juniper

Corresponding Certification: JNCIA-Junos

100% Juniper JN0-106 Guaranteed Success With Testking Training Materials

Get Real JN0-106 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

98 Questions & Answers with Testing Engine

"Junos, Associate (JNCIA-Junos) Exam", also known as JN0-106 exam, is a Juniper certification exam.

Pass your tests with the always up-to-date JN0-106 Exam Engine. Your JN0-106 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Juniper JN0-106 Practice Test 8

Question 70

Within Networking Fundamentals, a Junos engineer proposes the following response: Use valid FE80::/10 link-local IPv6 addresses on the local segment. Which concept or operating procedure is best illustrated?

  1. TCP connection setup
  2. Longest-prefix matching
  3. IPv6 link-local scope
  4. Decimal to binary conversion

Explanation

Correct Answer

C:

IPv6 link-local unicast addresses are for local-link communication and are not routed across ordinary routers. This meets the stated need for ipv6 link-local scope.

Incorrect Answers

A:

The tcp connection setup scenario has a different requirement: TCP is connection-oriented and provides ordered reliable delivery using sequence numbers, acknowledgments, and retransmission. It does not directly meet the ipv6 link-local scope need in this question.

B:

The longest-prefix matching scenario has a different requirement: IP forwarding chooses the longest matching destination prefix, independent of the broader route's presence. It does not directly meet the ipv6 link-local scope need in this question.

D:

The decimal to binary conversion scenario has a different requirement: Thirteen equals eight plus four plus one, so the 8, 4, and 1 bit positions are set. It does not directly meet the ipv6 link-local scope need in this question.

Question 71

Two routers on the same Ethernet segment exchange IPv6 neighbor messages without globally routable addresses. The proposed response is: Use valid FE80::/10 link-local IPv6 addresses on the local segment. Which explanation most accurately supports this response?

  1. TCP is connection-oriented and provides ordered reliable delivery using sequence numbers, acknowledgments, and retransmission.
  2. IP forwarding chooses the longest matching destination prefix, independent of the broader route's presence.
  3. Thirteen equals eight plus four plus one, so the 8, 4, and 1 bit positions are set.
  4. IPv6 link-local unicast addresses are for local-link communication and are not routed across ordinary routers.

Explanation

Correct Answer

D:

IPv6 link-local unicast addresses are for local-link communication and are not routed across ordinary routers. This meets the stated need for ipv6 link-local scope.

Incorrect Answers

A:

The tcp connection setup scenario has a different requirement: TCP is connection-oriented and provides ordered reliable delivery using sequence numbers, acknowledgments, and retransmission. It does not directly meet the ipv6 link-local scope need in this question.

B:

The longest-prefix matching scenario has a different requirement: IP forwarding chooses the longest matching destination prefix, independent of the broader route's presence. It does not directly meet the ipv6 link-local scope need in this question.

C:

The decimal to binary conversion scenario has a different requirement: Thirteen equals eight plus four plus one, so the 8, 4, and 1 bit positions are set. It does not directly meet the ipv6 link-local scope need in this question.

Question 72

Within Networking Fundamentals, a technician selects this approach: Use valid FE80::/10 link-local IPv6 addresses on the local segment. Which original requirement or fault would most directly justify it?

  1. An application needs reliable ordered delivery over an established byte-stream connection.
  2. A router learns 203.0.113.0/24 and the more-specific 203.0.113.128/25, then forwards to 203.0.113.140.
  3. Two routers on the same Ethernet segment exchange IPv6 neighbor messages without globally routable addresses.
  4. An addressing exercise asks for the eight-bit unsigned binary representation of decimal 13.

Explanation

Correct Answer

C:

IPv6 link-local unicast addresses are for local-link communication and are not routed across ordinary routers. This meets the stated need for ipv6 link-local scope.

Incorrect Answers

A:

The tcp connection setup scenario has a different requirement: TCP is connection-oriented and provides ordered reliable delivery using sequence numbers, acknowledgments, and retransmission. It does not directly meet the ipv6 link-local scope need in this question.

B:

The longest-prefix matching scenario has a different requirement: IP forwarding chooses the longest matching destination prefix, independent of the broader route's presence. It does not directly meet the ipv6 link-local scope need in this question.

D:

The decimal to binary conversion scenario has a different requirement: Thirteen equals eight plus four plus one, so the 8, 4, and 1 bit positions are set. It does not directly meet the ipv6 link-local scope need in this question.

Question 73

A client needs the network prefix and router information for IPv6 stateless autoconfiguration. Which configuration or troubleshooting action most directly meets the need?

  1. Allow the switch to learn the source MAC address and ingress port from frames sent by that host.
  2. Validate the path MTU and account for fragmentation or packet-size adjustment where supported.
  3. Use IPv6 Router Advertisements with appropriate prefix information on the segment.
  4. Treat an IPv6 address as 128 bits rather than 32 bits.

Explanation

Correct Answer

C:

SLAAC depends on ICMPv6 Router Advertisements to learn usable prefixes and related local network parameters. This meets the stated need for ipv6 router advertisements.

Incorrect Answers

A:

The ethernet source-mac learning scenario has a different requirement: Ethernet switches populate their forwarding database from source MAC addresses observed on ingress frames. It does not directly meet the ipv6 router advertisements need in this question.

B:

The ipv4 packet mtu scenario has a different requirement: An MTU constrains the maximum packet carried by a link, so oversized packets require compatible handling. It does not directly meet the ipv6 router advertisements need in this question.

D:

The ipv6 address width scenario has a different requirement: IPv6 uses 128-bit addresses represented as hexadecimal groups, much longer than 32-bit IPv4 addresses. It does not directly meet the ipv6 router advertisements need in this question.

Question 74

Within Networking Fundamentals, a Junos engineer proposes the following response: Use IPv6 Router Advertisements with appropriate prefix information on the segment. Which concept or operating procedure is best illustrated?

  1. IPv6 router advertisements
  2. Ethernet source-MAC learning
  3. IPv4 packet MTU
  4. IPv6 address width

Explanation

Correct Answer

A:

SLAAC depends on ICMPv6 Router Advertisements to learn usable prefixes and related local network parameters. This meets the stated need for ipv6 router advertisements.

Incorrect Answers

B:

The ethernet source-mac learning scenario has a different requirement: Ethernet switches populate their forwarding database from source MAC addresses observed on ingress frames. It does not directly meet the ipv6 router advertisements need in this question.

C:

The ipv4 packet mtu scenario has a different requirement: An MTU constrains the maximum packet carried by a link, so oversized packets require compatible handling. It does not directly meet the ipv6 router advertisements need in this question.

D:

The ipv6 address width scenario has a different requirement: IPv6 uses 128-bit addresses represented as hexadecimal groups, much longer than 32-bit IPv4 addresses. It does not directly meet the ipv6 router advertisements need in this question.

Question 75

A client needs the network prefix and router information for IPv6 stateless autoconfiguration. The proposed response is: Use IPv6 Router Advertisements with appropriate prefix information on the segment. Which explanation most accurately supports this response?

  1. SLAAC depends on ICMPv6 Router Advertisements to learn usable prefixes and related local network parameters.
  2. Ethernet switches populate their forwarding database from source MAC addresses observed on ingress frames.
  3. An MTU constrains the maximum packet carried by a link, so oversized packets require compatible handling.
  4. IPv6 uses 128-bit addresses represented as hexadecimal groups, much longer than 32-bit IPv4 addresses.

Explanation

Correct Answer

A:

SLAAC depends on ICMPv6 Router Advertisements to learn usable prefixes and related local network parameters. This meets the stated need for ipv6 router advertisements.

Incorrect Answers

B:

The ethernet source-mac learning scenario has a different requirement: Ethernet switches populate their forwarding database from source MAC addresses observed on ingress frames. It does not directly meet the ipv6 router advertisements need in this question.

C:

The ipv4 packet mtu scenario has a different requirement: An MTU constrains the maximum packet carried by a link, so oversized packets require compatible handling. It does not directly meet the ipv6 router advertisements need in this question.

D:

The ipv6 address width scenario has a different requirement: IPv6 uses 128-bit addresses represented as hexadecimal groups, much longer than 32-bit IPv4 addresses. It does not directly meet the ipv6 router advertisements need in this question.

Question 76

Within Networking Fundamentals, a technician selects this approach: Use IPv6 Router Advertisements with appropriate prefix information on the segment. Which original requirement or fault would most directly justify it?

  1. A switch initially has no forwarding entry for a newly connected host's Ethernet address.
  2. A large packet repeatedly fails across a link with an MTU smaller than its total size.
  3. A client needs the network prefix and router information for IPv6 stateless autoconfiguration.
  4. An engineer must compare the address space of IPv6 with 32-bit IPv4 addresses.

Explanation

Correct Answer

C:

SLAAC depends on ICMPv6 Router Advertisements to learn usable prefixes and related local network parameters. This meets the stated need for ipv6 router advertisements.

Incorrect Answers

A:

The ethernet source-mac learning scenario has a different requirement: Ethernet switches populate their forwarding database from source MAC addresses observed on ingress frames. It does not directly meet the ipv6 router advertisements need in this question.

B:

The ipv4 packet mtu scenario has a different requirement: An MTU constrains the maximum packet carried by a link, so oversized packets require compatible handling. It does not directly meet the ipv6 router advertisements need in this question.

D:

The ipv6 address width scenario has a different requirement: IPv6 uses 128-bit addresses represented as hexadecimal groups, much longer than 32-bit IPv4 addresses. It does not directly meet the ipv6 router advertisements need in this question.

Question 77

A host must learn which on-link IPv6 router can forward packets to destinations outside its subnet. Which configuration or troubleshooting action most directly meets the need?

  1. Send ICMP echo requests using ping and inspect the echo responses.
  2. Expect unknown unicast frames to be flooded within the VLAN until the destination MAC is learned.
  3. Learn the default router from IPv6 Router Advertisements rather than using ARP.
  4. Use destination MAC FF:FF:FF:FF:FF:FF for a Layer 2 broadcast frame.

Explanation

Correct Answer

C:

IPv6 Router Advertisements carry default-router information that hosts can use for off-link forwarding. This meets the stated need for ipv6 default-router discovery.

Incorrect Answers

A:

The icmp echo reachability scenario has a different requirement: Ping normally tests reachability by sending ICMP echo requests and observing returned echo replies. It does not directly meet the ipv6 default-router discovery need in this question.

B:

The unknown-unicast flooding scenario has a different requirement: A bridge cannot select one outgoing port for an unknown destination, so it floods eligible ports in that broadcast domain. It does not directly meet the ipv6 default-router discovery need in this question.

D:

The ethernet broadcast destination scenario has a different requirement: The all-ones Ethernet destination address denotes a broadcast received throughout the local VLAN. It does not directly meet the ipv6 default-router discovery need in this question.

Question 78

Within Networking Fundamentals, a Junos engineer proposes the following response: Learn the default router from IPv6 Router Advertisements rather than using ARP. Which concept or operating procedure is best illustrated?

  1. ICMP echo reachability
  2. IPv6 default-router discovery
  3. Unknown-unicast flooding
  4. Ethernet broadcast destination

Explanation

Correct Answer

B:

IPv6 Router Advertisements carry default-router information that hosts can use for off-link forwarding. This meets the stated need for ipv6 default-router discovery.

Incorrect Answers

A:

The icmp echo reachability scenario has a different requirement: Ping normally tests reachability by sending ICMP echo requests and observing returned echo replies. It does not directly meet the ipv6 default-router discovery need in this question.

C:

The unknown-unicast flooding scenario has a different requirement: A bridge cannot select one outgoing port for an unknown destination, so it floods eligible ports in that broadcast domain. It does not directly meet the ipv6 default-router discovery need in this question.

D:

The ethernet broadcast destination scenario has a different requirement: The all-ones Ethernet destination address denotes a broadcast received throughout the local VLAN. It does not directly meet the ipv6 default-router discovery need in this question.

Question 79

A host must learn which on-link IPv6 router can forward packets to destinations outside its subnet. The proposed response is: Learn the default router from IPv6 Router Advertisements rather than using ARP. Which explanation most accurately supports this response?

  1. Ping normally tests reachability by sending ICMP echo requests and observing returned echo replies.
  2. A bridge cannot select one outgoing port for an unknown destination, so it floods eligible ports in that broadcast domain.
  3. The all-ones Ethernet destination address denotes a broadcast received throughout the local VLAN.
  4. IPv6 Router Advertisements carry default-router information that hosts can use for off-link forwarding.

Explanation

Correct Answer

D:

IPv6 Router Advertisements carry default-router information that hosts can use for off-link forwarding. This meets the stated need for ipv6 default-router discovery.

Incorrect Answers

A:

The icmp echo reachability scenario has a different requirement: Ping normally tests reachability by sending ICMP echo requests and observing returned echo replies. It does not directly meet the ipv6 default-router discovery need in this question.

B:

The unknown-unicast flooding scenario has a different requirement: A bridge cannot select one outgoing port for an unknown destination, so it floods eligible ports in that broadcast domain. It does not directly meet the ipv6 default-router discovery need in this question.

C:

The ethernet broadcast destination scenario has a different requirement: The all-ones Ethernet destination address denotes a broadcast received throughout the local VLAN. It does not directly meet the ipv6 default-router discovery need in this question.

Question 80

Within Networking Fundamentals, a technician selects this approach: Learn the default router from IPv6 Router Advertisements rather than using ARP. Which original requirement or fault would most directly justify it?

  1. A host must learn which on-link IPv6 router can forward packets to destinations outside its subnet.
  2. A technician wants a quick IP-level reachability test that measures round-trip replies.
  3. A new Ethernet destination MAC address is absent from a switch's forwarding table.
  4. A frame must be delivered by switches to all ports in its local Ethernet broadcast domain.

Explanation

Correct Answer

A:

IPv6 Router Advertisements carry default-router information that hosts can use for off-link forwarding. This meets the stated need for ipv6 default-router discovery.

Incorrect Answers

B:

The icmp echo reachability scenario has a different requirement: Ping normally tests reachability by sending ICMP echo requests and observing returned echo replies. It does not directly meet the ipv6 default-router discovery need in this question.

C:

The unknown-unicast flooding scenario has a different requirement: A bridge cannot select one outgoing port for an unknown destination, so it floods eligible ports in that broadcast domain. It does not directly meet the ipv6 default-router discovery need in this question.

D:

The ethernet broadcast destination scenario has a different requirement: The all-ones Ethernet destination address denotes a broadcast received throughout the local VLAN. It does not directly meet the ipv6 default-router discovery need in this question.

Junos, Associate (JNCIA-Junos) (JN0-106) Practice Tests