McAfee-Secured Website

Exam Code: JN0-106

Exam Name: Junos, Associate (JNCIA-Junos)

Certification Provider: Juniper

Corresponding Certification: JNCIA-Junos

100% Juniper JN0-106 Guaranteed Success With Testking Training Materials

Get Real JN0-106 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

98 Questions & Answers with Testing Engine

"Junos, Associate (JNCIA-Junos) Exam", also known as JN0-106 exam, is a Juniper certification exam.

Pass your tests with the always up-to-date JN0-106 Exam Engine. Your JN0-106 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Juniper JN0-106 Practice Test 10

Question 90

Within Networking Fundamentals, a Junos engineer proposes the following response: Classify the sequence as TCP's three-way connection handshake. Which concept or operating procedure is best illustrated?

  1. TCP three-way handshake
  2. IPv6 address width
  3. Access-port VLAN assignment
  4. IEEE 802.1Q trunking

Explanation

Correct Answer

A:

The SYN, SYN-ACK, and ACK exchange synchronizes sequence numbers when a TCP connection is established. This meets the stated need for tcp three-way handshake.

Incorrect Answers

B:

The ipv6 address width scenario has a different requirement: IPv6 uses 128-bit addresses represented as hexadecimal groups, much longer than 32-bit IPv4 addresses. It does not directly meet the tcp three-way handshake need in this question.

C:

The access-port vlan assignment scenario has a different requirement: An access port associates untagged endpoint traffic with one configured VLAN instead of requiring the host to add tags. It does not directly meet the tcp three-way handshake need in this question.

D:

The ieee 802.1q trunking scenario has a different requirement: 802.1Q VLAN tags identify the logical Layer 2 segment carried over a shared physical link. It does not directly meet the tcp three-way handshake need in this question.

Question 91

A packet capture shows SYN, SYN-ACK, and ACK before payload exchange. The proposed response is: Classify the sequence as TCP's three-way connection handshake. Which explanation most accurately supports this response?

  1. IPv6 uses 128-bit addresses represented as hexadecimal groups, much longer than 32-bit IPv4 addresses.
  2. An access port associates untagged endpoint traffic with one configured VLAN instead of requiring the host to add tags.
  3. The SYN, SYN-ACK, and ACK exchange synchronizes sequence numbers when a TCP connection is established.
  4. 802.1Q VLAN tags identify the logical Layer 2 segment carried over a shared physical link.

Explanation

Correct Answer

C:

The SYN, SYN-ACK, and ACK exchange synchronizes sequence numbers when a TCP connection is established. This meets the stated need for tcp three-way handshake.

Incorrect Answers

A:

The ipv6 address width scenario has a different requirement: IPv6 uses 128-bit addresses represented as hexadecimal groups, much longer than 32-bit IPv4 addresses. It does not directly meet the tcp three-way handshake need in this question.

B:

The access-port vlan assignment scenario has a different requirement: An access port associates untagged endpoint traffic with one configured VLAN instead of requiring the host to add tags. It does not directly meet the tcp three-way handshake need in this question.

D:

The ieee 802.1q trunking scenario has a different requirement: 802.1Q VLAN tags identify the logical Layer 2 segment carried over a shared physical link. It does not directly meet the tcp three-way handshake need in this question.

Question 92

Within Networking Fundamentals, a technician selects this approach: Classify the sequence as TCP's three-way connection handshake. Which original requirement or fault would most directly justify it?

  1. A packet capture shows SYN, SYN-ACK, and ACK before payload exchange.
  2. An engineer must compare the address space of IPv6 with 32-bit IPv4 addresses.
  3. An ordinary workstation sends untagged frames and must be assigned to the finance broadcast domain.
  4. A single Ethernet uplink must carry user traffic belonging to three separate VLANs.

Explanation

Correct Answer

A:

The SYN, SYN-ACK, and ACK exchange synchronizes sequence numbers when a TCP connection is established. This meets the stated need for tcp three-way handshake.

Incorrect Answers

B:

The ipv6 address width scenario has a different requirement: IPv6 uses 128-bit addresses represented as hexadecimal groups, much longer than 32-bit IPv4 addresses. It does not directly meet the tcp three-way handshake need in this question.

C:

The access-port vlan assignment scenario has a different requirement: An access port associates untagged endpoint traffic with one configured VLAN instead of requiring the host to add tags. It does not directly meet the tcp three-way handshake need in this question.

D:

The ieee 802.1q trunking scenario has a different requirement: 802.1Q VLAN tags identify the logical Layer 2 segment carried over a shared physical link. It does not directly meet the tcp three-way handshake need in this question.

Question 93

A technician wants a quick IP-level reachability test that measures round-trip replies. Which configuration or troubleshooting action most directly meets the need?

  1. Use valid FE80::/10 link-local IPv6 addresses on the local segment.
  2. Use IPv6 Router Advertisements with appropriate prefix information on the segment.
  3. Use destination MAC FF:FF:FF:FF:FF:FF for a Layer 2 broadcast frame.
  4. Send ICMP echo requests using ping and inspect the echo responses.

Explanation

Correct Answer

D:

Ping normally tests reachability by sending ICMP echo requests and observing returned echo replies. This meets the stated need for icmp echo reachability.

Incorrect Answers

A:

The ipv6 link-local scope scenario has a different requirement: IPv6 link-local unicast addresses are for local-link communication and are not routed across ordinary routers. It does not directly meet the icmp echo reachability need in this question.

B:

The ipv6 router advertisements scenario has a different requirement: SLAAC depends on ICMPv6 Router Advertisements to learn usable prefixes and related local network parameters. It does not directly meet the icmp echo reachability need in this question.

C:

The ethernet broadcast destination scenario has a different requirement: The all-ones Ethernet destination address denotes a broadcast received throughout the local VLAN. It does not directly meet the icmp echo reachability need in this question.

Question 94

Within Networking Fundamentals, a Junos engineer proposes the following response: Send ICMP echo requests using ping and inspect the echo responses. Which concept or operating procedure is best illustrated?

  1. ICMP echo reachability
  2. IPv6 link-local scope
  3. IPv6 router advertisements
  4. Ethernet broadcast destination

Explanation

Correct Answer

A:

Ping normally tests reachability by sending ICMP echo requests and observing returned echo replies. This meets the stated need for icmp echo reachability.

Incorrect Answers

B:

The ipv6 link-local scope scenario has a different requirement: IPv6 link-local unicast addresses are for local-link communication and are not routed across ordinary routers. It does not directly meet the icmp echo reachability need in this question.

C:

The ipv6 router advertisements scenario has a different requirement: SLAAC depends on ICMPv6 Router Advertisements to learn usable prefixes and related local network parameters. It does not directly meet the icmp echo reachability need in this question.

D:

The ethernet broadcast destination scenario has a different requirement: The all-ones Ethernet destination address denotes a broadcast received throughout the local VLAN. It does not directly meet the icmp echo reachability need in this question.

Question 95

A technician wants a quick IP-level reachability test that measures round-trip replies. The proposed response is: Send ICMP echo requests using ping and inspect the echo responses. Which explanation most accurately supports this response?

  1. IPv6 link-local unicast addresses are for local-link communication and are not routed across ordinary routers.
  2. SLAAC depends on ICMPv6 Router Advertisements to learn usable prefixes and related local network parameters.
  3. The all-ones Ethernet destination address denotes a broadcast received throughout the local VLAN.
  4. Ping normally tests reachability by sending ICMP echo requests and observing returned echo replies.

Explanation

Correct Answer

D:

Ping normally tests reachability by sending ICMP echo requests and observing returned echo replies. This meets the stated need for icmp echo reachability.

Incorrect Answers

A:

The ipv6 link-local scope scenario has a different requirement: IPv6 link-local unicast addresses are for local-link communication and are not routed across ordinary routers. It does not directly meet the icmp echo reachability need in this question.

B:

The ipv6 router advertisements scenario has a different requirement: SLAAC depends on ICMPv6 Router Advertisements to learn usable prefixes and related local network parameters. It does not directly meet the icmp echo reachability need in this question.

C:

The ethernet broadcast destination scenario has a different requirement: The all-ones Ethernet destination address denotes a broadcast received throughout the local VLAN. It does not directly meet the icmp echo reachability need in this question.

Question 96

Within Networking Fundamentals, a technician selects this approach: Send ICMP echo requests using ping and inspect the echo responses. Which original requirement or fault would most directly justify it?

  1. Two routers on the same Ethernet segment exchange IPv6 neighbor messages without globally routable addresses.
  2. A client needs the network prefix and router information for IPv6 stateless autoconfiguration.
  3. A frame must be delivered by switches to all ports in its local Ethernet broadcast domain.
  4. A technician wants a quick IP-level reachability test that measures round-trip replies.

Explanation

Correct Answer

D:

Ping normally tests reachability by sending ICMP echo requests and observing returned echo replies. This meets the stated need for icmp echo reachability.

Incorrect Answers

A:

The ipv6 link-local scope scenario has a different requirement: IPv6 link-local unicast addresses are for local-link communication and are not routed across ordinary routers. It does not directly meet the icmp echo reachability need in this question.

B:

The ipv6 router advertisements scenario has a different requirement: SLAAC depends on ICMPv6 Router Advertisements to learn usable prefixes and related local network parameters. It does not directly meet the icmp echo reachability need in this question.

C:

The ethernet broadcast destination scenario has a different requirement: The all-ones Ethernet destination address denotes a broadcast received throughout the local VLAN. It does not directly meet the icmp echo reachability need in this question.

Question 97

A technician needs to reveal intermediate IP hops along a path to a remote server. Which configuration or troubleshooting action most directly meets the need?

  1. Run traceroute and inspect the responses triggered by successive hop-limit values.
  2. Validate the path MTU and account for fragmentation or packet-size adjustment where supported.
  3. Classify the sequence as TCP's three-way connection handshake.
  4. Learn the default router from IPv6 Router Advertisements rather than using ARP.

Explanation

Correct Answer

A:

Traceroute varies TTL or hop limit to elicit intermediate router responses and infer a packet path. This meets the stated need for traceroute ttl discovery.

Incorrect Answers

B:

The ipv4 packet mtu scenario has a different requirement: An MTU constrains the maximum packet carried by a link, so oversized packets require compatible handling. It does not directly meet the traceroute ttl discovery need in this question.

C:

The tcp three-way handshake scenario has a different requirement: The SYN, SYN-ACK, and ACK exchange synchronizes sequence numbers when a TCP connection is established. It does not directly meet the traceroute ttl discovery need in this question.

D:

The ipv6 default-router discovery scenario has a different requirement: IPv6 Router Advertisements carry default-router information that hosts can use for off-link forwarding. It does not directly meet the traceroute ttl discovery need in this question.

Question 98

Within Networking Fundamentals, a Junos engineer proposes the following response: Run traceroute and inspect the responses triggered by successive hop-limit values. Which concept or operating procedure is best illustrated?

  1. IPv4 packet MTU
  2. TCP three-way handshake
  3. Traceroute TTL discovery
  4. IPv6 default-router discovery

Explanation

Correct Answer

C:

Traceroute varies TTL or hop limit to elicit intermediate router responses and infer a packet path. This meets the stated need for traceroute ttl discovery.

Incorrect Answers

A:

The ipv4 packet mtu scenario has a different requirement: An MTU constrains the maximum packet carried by a link, so oversized packets require compatible handling. It does not directly meet the traceroute ttl discovery need in this question.

B:

The tcp three-way handshake scenario has a different requirement: The SYN, SYN-ACK, and ACK exchange synchronizes sequence numbers when a TCP connection is established. It does not directly meet the traceroute ttl discovery need in this question.

D:

The ipv6 default-router discovery scenario has a different requirement: IPv6 Router Advertisements carry default-router information that hosts can use for off-link forwarding. It does not directly meet the traceroute ttl discovery need in this question.

Question 99

A technician needs to reveal intermediate IP hops along a path to a remote server. The proposed response is: Run traceroute and inspect the responses triggered by successive hop-limit values. Which explanation most accurately supports this response?

  1. An MTU constrains the maximum packet carried by a link, so oversized packets require compatible handling.
  2. Traceroute varies TTL or hop limit to elicit intermediate router responses and infer a packet path.
  3. The SYN, SYN-ACK, and ACK exchange synchronizes sequence numbers when a TCP connection is established.
  4. IPv6 Router Advertisements carry default-router information that hosts can use for off-link forwarding.

Explanation

Correct Answer

B:

Traceroute varies TTL or hop limit to elicit intermediate router responses and infer a packet path. This meets the stated need for traceroute ttl discovery.

Incorrect Answers

A:

The ipv4 packet mtu scenario has a different requirement: An MTU constrains the maximum packet carried by a link, so oversized packets require compatible handling. It does not directly meet the traceroute ttl discovery need in this question.

C:

The tcp three-way handshake scenario has a different requirement: The SYN, SYN-ACK, and ACK exchange synchronizes sequence numbers when a TCP connection is established. It does not directly meet the traceroute ttl discovery need in this question.

D:

The ipv6 default-router discovery scenario has a different requirement: IPv6 Router Advertisements carry default-router information that hosts can use for off-link forwarding. It does not directly meet the traceroute ttl discovery need in this question.

Question 100

Within Networking Fundamentals, a technician selects this approach: Run traceroute and inspect the responses triggered by successive hop-limit values. Which original requirement or fault would most directly justify it?

  1. A large packet repeatedly fails across a link with an MTU smaller than its total size.
  2. A technician needs to reveal intermediate IP hops along a path to a remote server.
  3. A packet capture shows SYN, SYN-ACK, and ACK before payload exchange.
  4. A host must learn which on-link IPv6 router can forward packets to destinations outside its subnet.

Explanation

Correct Answer

B:

Traceroute varies TTL or hop limit to elicit intermediate router responses and infer a packet path. This meets the stated need for traceroute ttl discovery.

Incorrect Answers

A:

The ipv4 packet mtu scenario has a different requirement: An MTU constrains the maximum packet carried by a link, so oversized packets require compatible handling. It does not directly meet the traceroute ttl discovery need in this question.

C:

The tcp three-way handshake scenario has a different requirement: The SYN, SYN-ACK, and ACK exchange synchronizes sequence numbers when a TCP connection is established. It does not directly meet the traceroute ttl discovery need in this question.

D:

The ipv6 default-router discovery scenario has a different requirement: IPv6 Router Advertisements carry default-router information that hosts can use for off-link forwarding. It does not directly meet the traceroute ttl discovery need in this question.

Junos, Associate (JNCIA-Junos) (JN0-106) Practice Tests