McAfee-Secured Website

Exam Code: JN0-106

Exam Name: Junos, Associate (JNCIA-Junos)

Certification Provider: Juniper

Corresponding Certification: JNCIA-Junos

100% Juniper JN0-106 Guaranteed Success With Testking Training Materials

Get Real JN0-106 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

98 Questions & Answers with Testing Engine

"Junos, Associate (JNCIA-Junos) Exam", also known as JN0-106 exam, is a Juniper certification exam.

Pass your tests with the always up-to-date JN0-106 Exam Engine. Your JN0-106 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Juniper JN0-106 Practice Test 15

Question 140

Within Networking Fundamentals, a technician selects this approach: Use an active 0.0.0.0/0 default route toward the upstream gateway. Which original requirement or fault would most directly justify it?

  1. An IPv4 LAN uses a conventional /24 mask and reserves network and broadcast addresses.
  2. A branch router has no more specific route for a public destination but has an upstream Internet gateway.
  3. A technician wants a quick IP-level reachability test that measures round-trip replies.
  4. A single Ethernet uplink must carry user traffic belonging to three separate VLANs.

Explanation

Correct Answer

B:

The IPv4 default route matches any destination without a more-specific active prefix. This meets the stated need for ipv4 default route.

Incorrect Answers

A:

The ipv4 /24 usable hosts scenario has a different requirement: A /24 leaves eight host bits, yielding 256 addresses; the all-zero network and all-one broadcast addresses are reserved. It does not directly meet the ipv4 default route need in this question.

C:

The icmp echo reachability scenario has a different requirement: Ping normally tests reachability by sending ICMP echo requests and observing returned echo replies. It does not directly meet the ipv4 default route need in this question.

D:

The ieee 802.1q trunking scenario has a different requirement: 802.1Q VLAN tags identify the logical Layer 2 segment carried over a shared physical link. It does not directly meet the ipv4 default route need in this question.

Question 141

An IPv4 endpoint uses mask 255.255.255.128 and an engineer must state its prefix length. Which configuration or troubleshooting action most directly meets the need?

  1. Configure a VLAN-tagged 802.1Q trunk with the intended VLAN membership on both ends.
  2. Configure its switchport as an access port in the finance VLAN.
  3. Identify the subnet mask as a /25 prefix.
  4. Use valid FE80::/10 link-local IPv6 addresses on the local segment.

Explanation

Correct Answer

C:

The first 25 mask bits are set to one: 24 bits in the first three octets and one more in 128. This meets the stated need for subnet mask /25 interpretation.

Incorrect Answers

A:

The ieee 802.1q trunking scenario has a different requirement: 802.1Q VLAN tags identify the logical Layer 2 segment carried over a shared physical link. It does not directly meet the subnet mask /25 interpretation need in this question.

B:

The access-port vlan assignment scenario has a different requirement: An access port associates untagged endpoint traffic with one configured VLAN instead of requiring the host to add tags. It does not directly meet the subnet mask /25 interpretation need in this question.

D:

The ipv6 link-local scope scenario has a different requirement: IPv6 link-local unicast addresses are for local-link communication and are not routed across ordinary routers. It does not directly meet the subnet mask /25 interpretation need in this question.

Question 142

Within Networking Fundamentals, a Junos engineer proposes the following response: Identify the subnet mask as a /25 prefix. Which concept or operating procedure is best illustrated?

  1. IEEE 802.1Q trunking
  2. Access-port VLAN assignment
  3. IPv6 link-local scope
  4. Subnet mask /25 interpretation

Explanation

Correct Answer

D:

The first 25 mask bits are set to one: 24 bits in the first three octets and one more in 128. This meets the stated need for subnet mask /25 interpretation.

Incorrect Answers

A:

The ieee 802.1q trunking scenario has a different requirement: 802.1Q VLAN tags identify the logical Layer 2 segment carried over a shared physical link. It does not directly meet the subnet mask /25 interpretation need in this question.

B:

The access-port vlan assignment scenario has a different requirement: An access port associates untagged endpoint traffic with one configured VLAN instead of requiring the host to add tags. It does not directly meet the subnet mask /25 interpretation need in this question.

C:

The ipv6 link-local scope scenario has a different requirement: IPv6 link-local unicast addresses are for local-link communication and are not routed across ordinary routers. It does not directly meet the subnet mask /25 interpretation need in this question.

Question 143

An IPv4 endpoint uses mask 255.255.255.128 and an engineer must state its prefix length. The proposed response is: Identify the subnet mask as a /25 prefix. Which explanation most accurately supports this response?

  1. 802.1Q VLAN tags identify the logical Layer 2 segment carried over a shared physical link.
  2. An access port associates untagged endpoint traffic with one configured VLAN instead of requiring the host to add tags.
  3. The first 25 mask bits are set to one: 24 bits in the first three octets and one more in 128.
  4. IPv6 link-local unicast addresses are for local-link communication and are not routed across ordinary routers.

Explanation

Correct Answer

C:

The first 25 mask bits are set to one: 24 bits in the first three octets and one more in 128. This meets the stated need for subnet mask /25 interpretation.

Incorrect Answers

A:

The ieee 802.1q trunking scenario has a different requirement: 802.1Q VLAN tags identify the logical Layer 2 segment carried over a shared physical link. It does not directly meet the subnet mask /25 interpretation need in this question.

B:

The access-port vlan assignment scenario has a different requirement: An access port associates untagged endpoint traffic with one configured VLAN instead of requiring the host to add tags. It does not directly meet the subnet mask /25 interpretation need in this question.

D:

The ipv6 link-local scope scenario has a different requirement: IPv6 link-local unicast addresses are for local-link communication and are not routed across ordinary routers. It does not directly meet the subnet mask /25 interpretation need in this question.

Question 144

Within Networking Fundamentals, a technician selects this approach: Identify the subnet mask as a /25 prefix. Which original requirement or fault would most directly justify it?

  1. A single Ethernet uplink must carry user traffic belonging to three separate VLANs.
  2. An IPv4 endpoint uses mask 255.255.255.128 and an engineer must state its prefix length.
  3. An ordinary workstation sends untagged frames and must be assigned to the finance broadcast domain.
  4. Two routers on the same Ethernet segment exchange IPv6 neighbor messages without globally routable addresses.

Explanation

Correct Answer

B:

The first 25 mask bits are set to one: 24 bits in the first three octets and one more in 128. This meets the stated need for subnet mask /25 interpretation.

Incorrect Answers

A:

The ieee 802.1q trunking scenario has a different requirement: 802.1Q VLAN tags identify the logical Layer 2 segment carried over a shared physical link. It does not directly meet the subnet mask /25 interpretation need in this question.

C:

The access-port vlan assignment scenario has a different requirement: An access port associates untagged endpoint traffic with one configured VLAN instead of requiring the host to add tags. It does not directly meet the subnet mask /25 interpretation need in this question.

D:

The ipv6 link-local scope scenario has a different requirement: IPv6 link-local unicast addresses are for local-link communication and are not routed across ordinary routers. It does not directly meet the subnet mask /25 interpretation need in this question.

Question 145

A host at 192.0.2.10/24 wants to reach 192.0.2.20 on the same Ethernet VLAN. Which configuration or troubleshooting action most directly meets the need?

  1. Learn the default router from IPv6 Router Advertisements rather than using ARP.
  2. Validate the path MTU and account for fragmentation or packet-size adjustment where supported.
  3. Use ARP resolution to learn the peer's link-layer address before sending the Ethernet frame.
  4. Resolve the destination host's MAC and send directly rather than via the default gateway.

Explanation

Correct Answer

D:

An on-link IPv4 destination is delivered locally at Layer 2 after neighbor resolution. This meets the stated need for same-subnet direct forwarding.

Incorrect Answers

A:

The ipv6 default-router discovery scenario has a different requirement: IPv6 Router Advertisements carry default-router information that hosts can use for off-link forwarding. It does not directly meet the same-subnet direct forwarding need in this question.

B:

The ipv4 packet mtu scenario has a different requirement: An MTU constrains the maximum packet carried by a link, so oversized packets require compatible handling. It does not directly meet the same-subnet direct forwarding need in this question.

C:

The ipv4 arp resolution scenario has a different requirement: ARP maps an IPv4 address on a local link to the MAC address used to deliver Ethernet frames. It does not directly meet the same-subnet direct forwarding need in this question.

Question 146

Within Networking Fundamentals, a Junos engineer proposes the following response: Resolve the destination host's MAC and send directly rather than via the default gateway. Which concept or operating procedure is best illustrated?

  1. IPv6 default-router discovery
  2. IPv4 packet MTU
  3. Same-subnet direct forwarding
  4. IPv4 ARP resolution

Explanation

Correct Answer

C:

An on-link IPv4 destination is delivered locally at Layer 2 after neighbor resolution. This meets the stated need for same-subnet direct forwarding.

Incorrect Answers

A:

The ipv6 default-router discovery scenario has a different requirement: IPv6 Router Advertisements carry default-router information that hosts can use for off-link forwarding. It does not directly meet the same-subnet direct forwarding need in this question.

B:

The ipv4 packet mtu scenario has a different requirement: An MTU constrains the maximum packet carried by a link, so oversized packets require compatible handling. It does not directly meet the same-subnet direct forwarding need in this question.

D:

The ipv4 arp resolution scenario has a different requirement: ARP maps an IPv4 address on a local link to the MAC address used to deliver Ethernet frames. It does not directly meet the same-subnet direct forwarding need in this question.

Question 147

A host at 192.0.2.10/24 wants to reach 192.0.2.20 on the same Ethernet VLAN. The proposed response is: Resolve the destination host's MAC and send directly rather than via the default gateway. Which explanation most accurately supports this response?

  1. IPv6 Router Advertisements carry default-router information that hosts can use for off-link forwarding.
  2. An MTU constrains the maximum packet carried by a link, so oversized packets require compatible handling.
  3. ARP maps an IPv4 address on a local link to the MAC address used to deliver Ethernet frames.
  4. An on-link IPv4 destination is delivered locally at Layer 2 after neighbor resolution.

Explanation

Correct Answer

D:

An on-link IPv4 destination is delivered locally at Layer 2 after neighbor resolution. This meets the stated need for same-subnet direct forwarding.

Incorrect Answers

A:

The ipv6 default-router discovery scenario has a different requirement: IPv6 Router Advertisements carry default-router information that hosts can use for off-link forwarding. It does not directly meet the same-subnet direct forwarding need in this question.

B:

The ipv4 packet mtu scenario has a different requirement: An MTU constrains the maximum packet carried by a link, so oversized packets require compatible handling. It does not directly meet the same-subnet direct forwarding need in this question.

C:

The ipv4 arp resolution scenario has a different requirement: ARP maps an IPv4 address on a local link to the MAC address used to deliver Ethernet frames. It does not directly meet the same-subnet direct forwarding need in this question.

Question 148

Within Networking Fundamentals, a technician selects this approach: Resolve the destination host's MAC and send directly rather than via the default gateway. Which original requirement or fault would most directly justify it?

  1. A host must learn which on-link IPv6 router can forward packets to destinations outside its subnet.
  2. A large packet repeatedly fails across a link with an MTU smaller than its total size.
  3. A host at 192.0.2.10/24 wants to reach 192.0.2.20 on the same Ethernet VLAN.
  4. A host knows the on-link IPv4 address of a peer but has no Ethernet destination MAC address.

Explanation

Correct Answer

C:

An on-link IPv4 destination is delivered locally at Layer 2 after neighbor resolution. This meets the stated need for same-subnet direct forwarding.

Incorrect Answers

A:

The ipv6 default-router discovery scenario has a different requirement: IPv6 Router Advertisements carry default-router information that hosts can use for off-link forwarding. It does not directly meet the same-subnet direct forwarding need in this question.

B:

The ipv4 packet mtu scenario has a different requirement: An MTU constrains the maximum packet carried by a link, so oversized packets require compatible handling. It does not directly meet the same-subnet direct forwarding need in this question.

D:

The ipv4 arp resolution scenario has a different requirement: ARP maps an IPv4 address on a local link to the MAC address used to deliver Ethernet frames. It does not directly meet the same-subnet direct forwarding need in this question.

Question 149

A host at 192.0.2.10/24 sends to 198.51.100.20 outside its local prefix. Which configuration or troubleshooting action most directly meets the need?

  1. Replace the repeater with a switch that provides a separate collision domain for each full-duplex port.
  2. Resolve the configured default gateway's MAC address and forward the frame to that gateway.
  3. Treat an IPv6 address as 128 bits rather than 32 bits.
  4. Convert decimal 13 to 00001101 in eight-bit binary notation.

Explanation

Correct Answer

B:

For an off-link IP destination, the Ethernet next hop is the router while the IP destination remains remote. This meets the stated need for off-subnet gateway forwarding.

Incorrect Answers

A:

The collision-domain isolation scenario has a different requirement: A switch separates contention at each port, whereas a hub repeats traffic into one shared collision domain. It does not directly meet the off-subnet gateway forwarding need in this question.

C:

The ipv6 address width scenario has a different requirement: IPv6 uses 128-bit addresses represented as hexadecimal groups, much longer than 32-bit IPv4 addresses. It does not directly meet the off-subnet gateway forwarding need in this question.

D:

The decimal to binary conversion scenario has a different requirement: Thirteen equals eight plus four plus one, so the 8, 4, and 1 bit positions are set. It does not directly meet the off-subnet gateway forwarding need in this question.

Question 150

Within Networking Fundamentals, a Junos engineer proposes the following response: Resolve the configured default gateway's MAC address and forward the frame to that gateway. Which concept or operating procedure is best illustrated?

  1. Off-subnet gateway forwarding
  2. Collision-domain isolation
  3. IPv6 address width
  4. Decimal to binary conversion

Explanation

Correct Answer

A:

For an off-link IP destination, the Ethernet next hop is the router while the IP destination remains remote. This meets the stated need for off-subnet gateway forwarding.

Incorrect Answers

B:

The collision-domain isolation scenario has a different requirement: A switch separates contention at each port, whereas a hub repeats traffic into one shared collision domain. It does not directly meet the off-subnet gateway forwarding need in this question.

C:

The ipv6 address width scenario has a different requirement: IPv6 uses 128-bit addresses represented as hexadecimal groups, much longer than 32-bit IPv4 addresses. It does not directly meet the off-subnet gateway forwarding need in this question.

D:

The decimal to binary conversion scenario has a different requirement: Thirteen equals eight plus four plus one, so the 8, 4, and 1 bit positions are set. It does not directly meet the off-subnet gateway forwarding need in this question.

Junos, Associate (JNCIA-Junos) (JN0-106) Practice Tests