McAfee-Secured Website

Exam Bundle

Exam Code: 200-301

Exam Name Cisco Certified Network Associate (CCNA)

Certification Provider: Cisco

Corresponding Certification: CCNA

Cisco 200-301 Bundle $44.99

100% Cisco 200-301 Guaranteed Success With Testking Training Materials

Get Real 200-301 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

  • Questions & Answers

    200-301 Questions & Answers

    760 Questions & Answers

    The ultimate exam preparation tool, Questions & Answers mirrors the actual 200-301 exam while allowing you to hone and measure every aspect of your test-taking ability.

  • 200-301 Video Course

    200-301 Video Course

    271 Video Lectures

    200-301 Video Course is developed by Cisco Professionals to help you pass the 200-301 exam.

    Description

    This course will improve your knowledge and skills required to pass Cisco Certified Network Associate (CCNA) exam.
  • Study Guide

    200-301 Study Guide

    1969 PDF Pages

    Developed by industry experts, this 1969-page guide spells out in painstaking detail all of the information you need to ace 200-301 exam.

Cisco Certified Network Associate (CCNA) (200-301) Practice Tests

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Total Cost: $194.97
Bundle Price: $149.98

Purchase Individually

  • Questions & Answers

    Questions & Answers

    760 Questions

    $124.99
  • 200-301 Video Course

    Video Course

    271 Video Lectures

    $39.99
  • Study Guide

    Study Guide

    1969 PDF Pages

    $29.99

Cisco 200-301 Practice Test 62

Question 610

R3 and R4 are both DROTHER routers on one broadcast OSPF LAN. They each reach FULL with the DR but see 2-WAY with each other. Which diagnosis is correct?

  1. All OSPF pairs must always reach FULL with one another.
  2. The two routers have duplicate router IDs.
  3. This is normal DROTHER behavior on a multiaccess network.
  4. A 2-WAY state means their IP addressing is necessarily in different subnets.

Explanation

Correct Answer

C:

DROTHER routers can remain 2-WAY with each other while forming full adjacencies with DR and BDR.

Incorrect Answers

A:

Multiaccess OSPF uses DR/BDR to limit full adjacency mesh, so FULL between every pair is unnecessary.

B:

A 2-WAY state alone does not prove duplicate router IDs.

D:

These routers exchanged Hellos; the state is not proof of mismatched addressing.

Question 611

After a router reload, the local OSPFv2 router ID is 10.1.1.1 even though Gi0/0 has 192.0.2.100 and Loopback0 is 10.1.1.1. With no explicit router-id setting, why was 10.1.1.1 selected?

  1. Router ID must always equal the router’s highest physical interface IP
  2. The router prefers the highest loopback IPv4 address over physical interface addresses
  3. A lower loopback IPv4 value is always preferred over a higher one
  4. Router ID is copied from the first received OSPF Hello

Explanation

Correct Answer

B:

Absent a configured ID, IOS ordinarily selects the highest loopback address before considering physical interfaces.

Incorrect Answers

A:

A loopback address takes precedence over an active physical interface in automatic selection.

C:

Automatic selection normally chooses the highest eligible loopback address.

D:

Each router selects its own identifier, not one copied from a neighbor.

Question 612

Two IOS routers connect to a common Ethernet switch, and OSPFv2 is enabled without `ip ospf network` overrides. Which network type and election behavior should be expected?

  1. Nonbroadcast type that automatically disables Hellos.
  2. Broadcast type with DR/BDR election.
  3. Point-to-multipoint type with no DR election.
  4. Point-to-point type with no DR election.

Explanation

Correct Answer

B:

On ordinary Ethernet broadcast interfaces, OSPF defaults to broadcast network type, using DR/BDR election.

Incorrect Answers

A:

Nonbroadcast networks have different neighbor-discovery defaults and are not the stated default type.

C:

Point-to-multipoint is not normally inferred by IOS just because Ethernet is present.

D:

Point-to-point is not the normal default on a shared Ethernet broadcast segment.

Question 613

R1’s Gi0/2 has IPv4 10.4.8.1/30 and should join OSPF process 10 area 0 without a router-level `network` command. Which interface subcommand enables it?

  1. `network 10.4.8.0 0.0.0.3 area 0` under interface mode
  2. `ip ospf 10 area 0`
  3. `router ospf 10` under interface mode
  4. `ip ospf 0 area 10`

Explanation

Correct Answer

B:

Interface-level syntax identifies the local OSPF process then area, activating OSPF on that interface.

Incorrect Answers

A:

The network wildcard command belongs under router ospf configuration, not interface mode.

C:

router ospf begins routing-process configuration from global mode, not interface submode.

D:

This reverses the process ID and area arguments; it would join different identifiers.

Question 614

DIST1 and R2 have correct area 0 addresses and matching OSPF Hello/Dead timers on their shared routed link, but DIST1 configured `passive-interface GigabitEthernet0/0` under OSPF. R2 never receives DIST1 Hellos. What is the corrective action?

  1. Change DIST1 to a larger OSPF process ID than R2
  2. Enable `passive-interface default` on DIST1 without any exceptions
  3. Remove the passive setting on the transit interface so OSPF Hellos can be sent
  4. Set both router IDs to the same value to force adjacency

Explanation

Correct Answer

C:

An OSPF passive interface advertises its connected network without establishing neighbors on that interface; the transit link must not be passive.

Incorrect Answers

A:

OSPF process numbers have local significance and do not force a router to send Hello packets.

B:

Making more interfaces passive would suppress additional Hellos rather than restore the transit adjacency.

D:

Duplicate router IDs create another OSPF problem and do not overcome suppressed Hellos.

Question 615

Two OSPFv2 paths to a destination are available. The engineer must make one router-interface path less preferred by directly raising its OSPF cost. Which IOS interface command changes that metric?

  1. ip ospf cost 40
  2. ip ospf priority 40
  3. ip access-group 40 out
  4. spanning-tree cost 40

Explanation

Correct Answer

A:

The interface command sets the outgoing OSPF link metric used in path cost calculations.

Incorrect Answers

B:

OSPF priority affects DR/BDR election, not the OSPF path metric.

C:

An ACL application does not set OSPF metric values.

D:

This changes Layer 2 STP cost rather than OSPF IP routing cost.

Question 616

A router learns 10.88.0.0/16 from OSPF (AD 110) and has a normal static route (AD 1) for exactly 10.88.0.0/16 through a reachable next hop. Which route is preferred?

  1. Both routes are guaranteed equal-cost because masks match
  2. The static route with administrative distance 1
  3. The route advertised by whichever router has the highest OSPF DR priority
  4. The OSPF route because it uses a dynamic protocol

Explanation

Correct Answer

B:

For equal prefixes, IOS normally prefers the lower-AD installed static route over OSPF AD 110.

Incorrect Answers

A:

Different administrative distances normally prevent equal-cost installation across those paths.

C:

DR priority is not the route-source administrative-distance comparison.

D:

A route protocol being dynamic does not override a lower administrative distance.

Question 617

The interface 192.168.80.65/26 should participate in area 0 for an existing OSPFv2 process. Which network statement matches exactly its /26 subnet?

  1. `network 192.168.80.128 0.0.0.63 area 0`
  2. `network 192.168.80.0 0.0.0.63 area 0`
  3. `network 192.168.80.64 0.0.0.63 area 0`
  4. `network 192.168.80.64 255.255.255.192 area 0`

Explanation

Correct Answer

C:

The /26 network starts at .64 and uses wildcard 0.0.0.63; the statement matches interface addresses within that block.

Incorrect Answers

A:

The .128/26 network contains .128–.191 and excludes .65.

B:

The .0/26 network contains .0–.63 and excludes .65.

D:

The command expects an inverse wildcard, not the /26 subnet mask.

Question 618

An IOS operator needs to see whether R2 is FULL with its OSPFv2 neighbors and which interfaces each neighbor uses. Which command provides the neighbor state table?

  1. `show spanning-tree vlan 1`
  2. `show ip route static`
  3. `show cdp neighbors`
  4. `show ip ospf neighbor`

Explanation

Correct Answer

D:

show ip ospf neighbor lists router IDs, priorities, state, dead time, neighbor addresses and local interfaces.

Incorrect Answers

A:

Spanning tree operates at Layer 2 and does not track OSPF adjacency.

B:

Static routes do not list OSPF neighbor states.

C:

CDP reports Layer 2 discovery neighbors, not OSPF FULL/2-WAY state.

Question 619

Two equal-AD OSPF routes to 10.60.8.0/24 are in the LSDB with total path costs 24 and 72. What metric principle decides the selected path?

  1. The OSPF path with cumulative cost 24 is preferred.
  2. The path with cost 72 is preferred because it is numerically larger.
  3. The path with the highest local OSPF process ID always wins.
  4. The default route overrides both more-specific /24s.

Explanation

Correct Answer

A:

For equal-length destinations learned by OSPF, SPF seeks the lowest cumulative cost.

Incorrect Answers

B:

A larger OSPF cost represents a less preferred path for that prefix.

C:

Local OSPF process IDs are not transmitted as preference values for route comparison.

D:

A default route loses to a matching /24 by longest-prefix selection.

Question 620

Two links are 10 Gbps and 1 Gbps, but both receive the same default OSPF cost under an old reference bandwidth. Which adjustment enables useful cost distinction?

  1. Change the local OSPF process number from 10 to 1000.
  2. Increase the OSPF dead interval to 40 seconds only on the faster link.
  3. Lower switch access VLAN IDs on the uplinks.
  4. Increase OSPF auto-cost reference-bandwidth consistently on all routers in the domain.

Explanation

Correct Answer

D:

OSPF auto-cost derives interface cost from reference bandwidth; a higher consistent reference can differentiate higher-speed links.

Incorrect Answers

A:

Process ID names local routing instances and does not change interface metric math.

B:

Timers control neighbor liveness and must agree; they do not establish link bandwidth cost.

C:

VLAN numbers do not set OSPF reference bandwidth.