McAfee-Secured Website

Exam Bundle

Exam Code: 200-301

Exam Name Cisco Certified Network Associate (CCNA)

Certification Provider: Cisco

Corresponding Certification: CCNA

Cisco 200-301 Bundle $44.99

100% Cisco 200-301 Guaranteed Success With Testking Training Materials

Get Real 200-301 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

  • Questions & Answers

    200-301 Questions & Answers

    760 Questions & Answers

    The ultimate exam preparation tool, Questions & Answers mirrors the actual 200-301 exam while allowing you to hone and measure every aspect of your test-taking ability.

  • 200-301 Video Course

    200-301 Video Course

    271 Video Lectures

    200-301 Video Course is developed by Cisco Professionals to help you pass the 200-301 exam.

    Description

    This course will improve your knowledge and skills required to pass Cisco Certified Network Associate (CCNA) exam.
  • Study Guide

    200-301 Study Guide

    1969 PDF Pages

    Developed by industry experts, this 1969-page guide spells out in painstaking detail all of the information you need to ace 200-301 exam.

Cisco Certified Network Associate (CCNA) (200-301) Practice Tests

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Total Cost: $194.97
Bundle Price: $149.98

Purchase Individually

  • Questions & Answers

    Questions & Answers

    760 Questions

    $124.99
  • 200-301 Video Course

    Video Course

    271 Video Lectures

    $39.99
  • Study Guide

    Study Guide

    1969 PDF Pages

    $29.99

Cisco 200-301 Practice Test 61

Question 600

An OSPFv2 interface participating in a broadcast VLAN reports `Priority 0` in `show ip ospf interface`. The operator wants to know if the router can be elected DR on that VLAN. Which conclusion follows?

  1. It is guaranteed to become DR because zero is the best priority
  2. It is ineligible to become DR or BDR while its interface priority is zero
  3. The interface must be point-to-point because priority is zero
  4. The router stops sending Hellos solely due to interface priority zero

Explanation

Correct Answer

B:

A priority of zero excludes an OSPF router from DR and BDR elections on that broadcast segment.

Incorrect Answers

A:

OSPF chooses higher eligible priorities, not the smallest.

C:

Broadcast interfaces can have priority zero while still forming permitted neighbor relationships.

D:

Passive-interface configuration, not DR priority zero, suppresses Hellos.

Question 601

A 10-Gbps point-to-point routed interconnect has exactly two OSPFv2 routers and no shared multiaccess segment. Which OSPF interface network type avoids DR/BDR election?

  1. broadcast
  2. nonbroadcast
  3. point-to-point
  4. point-to-multipoint with a DR

Explanation

Correct Answer

C:

OSPF point-to-point networks form the pairwise adjacency without DR or BDR elections.

Incorrect Answers

A:

Broadcast multiaccess OSPF uses DR/BDR election on Ethernet by default.

B:

Nonbroadcast multiaccess is not the appropriate point-to-point link type for this case.

D:

Point-to-multipoint is not described by an ordinary two-router routed point-to-point link.

Question 602

A campus router must include subnet 10.70.5.0/24 in OSPF but never form OSPF neighbors with user PCs on that LAN. Which option accomplishes both?

  1. Change the LAN mask to /30 to reduce OSPF Hellos.
  2. Advertise the LAN in OSPF and apply `passive-interface` to its LAN-facing interface.
  3. Remove the LAN from all OSPF network/interface matches.
  4. Make every transit interface passive so no routing neighbors exist.

Explanation

Correct Answer

B:

A passive OSPF interface advertises its connected network while suppressing Hello neighbor formation on that interface.

Incorrect Answers

A:

A smaller mask changes addressing and does not constitute an OSPF neighbor-control setting.

C:

Removing the subnet from OSPF prevents it from being announced.

D:

Passive transit interfaces would prevent needed routing adjacencies.

Question 603

Two directly connected routers share Ethernet subnet 192.0.2.0/30 and area 0. `show ip ospf interface` shows R1 Hello/Dead 10/40 seconds, but R2 uses 5/20. Their OSPFv2 adjacency never forms. What should be changed?

  1. Set the local OSPF process number to match the remote process number
  2. Configure compatible Hello and Dead intervals on both ends of the OSPF link
  3. Raise the IP routing-table administrative distance to 200 on both routers
  4. Change only the Ethernet interface descriptions on both routers

Explanation

Correct Answer

B:

An OSPFv2 neighbor must accept compatible Hello and Dead timing on the shared interface to establish adjacency.

Incorrect Answers

A:

Local process IDs do not have to match across OSPF neighbors; timers, area and other link parameters matter instead.

C:

Administrative distance ranks learned route sources but does not fix OSPF Hello parameter mismatches.

D:

An interface description is not exchanged in OSPF Hello packets and cannot reconcile the timer values.

Question 604

A router is connected to an Ethernet OSPF LAN but the operator wants it never to become designated or backup designated router. Which interface command meets this?

  1. ip ospf cost 0
  2. ip ospf priority 0
  3. router ospf 0 on the interface
  4. spanning-tree root primary

Explanation

Correct Answer

B:

OSPF interface priority zero excludes a router from DR/BDR candidacy.

Incorrect Answers

A:

OSPF cost is a route metric rather than DR eligibility, and zero is not the intended feature.

C:

This is not the IOS interface command to disable DR candidacy.

D:

An STP root setting affects Layer 2 bridging, not OSPF DR selection.

Question 605

HQ-RT starts OSPFv2 without an explicit `router-id`. Its up loopbacks are Loopback0 10.10.70.1/32 and Loopback1 10.10.90.1/32; a routed physical interface uses 192.0.2.100/24. What router ID is normally selected at process startup?

  1. 192.0.2.100, because it is numerically higher than both loopback addresses
  2. 10.10.70.1, because Loopback0 was configured first
  3. 10.10.90.1, the highest IPv4 loopback interface address
  4. 0.0.0.0, because an explicit router-id command is mandatory

Explanation

Correct Answer

C:

10.10.90.1 is the highest IPv4 loopback address, and default OSPF router-ID selection prefers loopbacks over other interfaces.

Incorrect Answers

A:

An active loopback IP takes precedence over a larger physical-interface IP for default IOS OSPF router-ID election.

B:

With multiple loopbacks, IOS selects the numerically highest loopback address, not necessarily the lowest-numbered interface.

D:

OSPF can select a router ID automatically when valid IPv4 interface addressing is available.

Question 606

Three OSPFv2 routers join the same newly created broadcast VLAN with interface priorities R1=1, R2=50 and R3=0. Which router is elected DR when all join together?

  1. R1
  2. The router with the greatest configured OSPF process number
  3. R2
  4. R3

Explanation

Correct Answer

C:

Priority 50 outranks 1, while priority 0 makes a router ineligible to be DR/BDR.

Incorrect Answers

A:

R1 is eligible but loses to a higher priority.

B:

OSPF process numbers are local labels, not DR election inputs.

D:

Priority 0 makes R3 ineligible even when its router ID is large.

Question 607

A fresh broadcast OSPF segment has R1 priority 100, R2 priority 50 and R3 priority 1 with unique router IDs. Assuming all are eligible, which router should be selected as BDR?

  1. R3
  2. R2
  3. R1
  4. No BDR is elected on broadcast multiaccess networks

Explanation

Correct Answer

B:

R1 is first for DR; R2 has the next highest nonzero interface priority and becomes BDR.

Incorrect Answers

A:

R3 has lower priority than R2 and cannot win the BDR preference.

C:

R1 is DR, not BDR, in the stated fresh election.

D:

Broadcast OSPF elects both DR and BDR when multiple eligible routers participate.

Question 608

On a stable broadcast Ethernet OSPF area 0 network, R1 already serves as DR. R2 boots with interface priority 255, higher than R1. What happens without any DR failure or election reset?

  1. The network automatically turns into point-to-point type.
  2. R2 immediately seizes DR solely because of priority 255.
  3. R1 remains DR; OSPF DR election is not preemptive.
  4. Every neighbor transitions to passive-interface.

Explanation

Correct Answer

C:

A new higher-priority router does not displace an existing elected DR while the current DR remains operational.

Incorrect Answers

A:

OSPF network type is configured/detected, not changed by router priority alone.

B:

Higher priority influences future elections but does not instantly preempt the live DR.

D:

Passive-interface is a separate operator setting, not an election consequence.

Question 609

OSPFv2 neighbors reach EXSTART/EXCHANGE but repeatedly fail to become FULL. Interface IPs and timers agree, but one side uses an IP MTU of 1500 and the other 9000. What should be checked first?

  1. Resolve the OSPF interface MTU mismatch to permit database description exchange.
  2. Disable the adjacency by making both ends passive.
  3. Set the interfaces to different OSPF areas.
  4. Change the local OSPF process ID to match the peer.

Explanation

Correct Answer

A:

An MTU inconsistency can block DBD negotiation at EXSTART/EXCHANGE although Hello discovery succeeds.

Incorrect Answers

B:

Making interfaces passive suppresses Hellos rather than helping reach FULL.

C:

Area mismatch would prevent normal adjacency; it does not repair DBD exchange.

D:

Local process IDs do not have to match for OSPF neighbors.

Question 610

R3 and R4 are both DROTHER routers on one broadcast OSPF LAN. They each reach FULL with the DR but see 2-WAY with each other. Which diagnosis is correct?

  1. All OSPF pairs must always reach FULL with one another.
  2. The two routers have duplicate router IDs.
  3. This is normal DROTHER behavior on a multiaccess network.
  4. A 2-WAY state means their IP addressing is necessarily in different subnets.

Explanation

Correct Answer

C:

DROTHER routers can remain 2-WAY with each other while forming full adjacencies with DR and BDR.

Incorrect Answers

A:

Multiaccess OSPF uses DR/BDR to limit full adjacency mesh, so FULL between every pair is unnecessary.

B:

A 2-WAY state alone does not prove duplicate router IDs.

D:

These routers exchanged Hellos; the state is not proof of mismatched addressing.