McAfee-Secured Website

Exam Bundle

Exam Code: 200-301

Exam Name Cisco Certified Network Associate (CCNA)

Certification Provider: Cisco

Corresponding Certification: CCNA

Cisco 200-301 Bundle $44.99

100% Cisco 200-301 Guaranteed Success With Testking Training Materials

Get Real 200-301 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

  • Questions & Answers

    200-301 Questions & Answers

    760 Questions & Answers

    The ultimate exam preparation tool, Questions & Answers mirrors the actual 200-301 exam while allowing you to hone and measure every aspect of your test-taking ability.

  • 200-301 Video Course

    200-301 Video Course

    271 Video Lectures

    200-301 Video Course is developed by Cisco Professionals to help you pass the 200-301 exam.

    Description

    This course will improve your knowledge and skills required to pass Cisco Certified Network Associate (CCNA) exam.
  • Study Guide

    200-301 Study Guide

    1969 PDF Pages

    Developed by industry experts, this 1969-page guide spells out in painstaking detail all of the information you need to ace 200-301 exam.

Cisco Certified Network Associate (CCNA) (200-301) Practice Tests

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Total Cost: $194.97
Bundle Price: $149.98

Purchase Individually

  • Questions & Answers

    Questions & Answers

    760 Questions

    $124.99
  • 200-301 Video Course

    Video Course

    271 Video Lectures

    $39.99
  • Study Guide

    Study Guide

    1969 PDF Pages

    $29.99

Cisco 200-301 Practice Test 59

Question 580

A technician tries to configure a network route to 10.9.32.0/20 through next hop 192.0.2.1. Which form uses the correct dotted mask and destination boundary?

  1. ip route 10.9.32.0 255.255.240.0 192.0.2.1
  2. ip route 10.9.32.0 255.255.248.0 192.0.2.1
  3. ip route 10.9.40.0 255.255.240.0 192.0.2.1
  4. ip route 10.9.32.0 255.255.224.0 192.0.2.1

Explanation

Correct Answer

A:

A /20 spans third octets 32–47 and has mask 255.255.240.0.

Incorrect Answers

B:

Mask 255.255.248.0 is /21 and covers only half of the requested /20.

C:

Third octet 40 is not an aligned /20 network boundary.

D:

Mask 255.255.224.0 is /19, which is twice as broad as /20.

Question 581

A router has `S* 0.0.0.0/0 via 192.0.2.5` and `O 172.16.40.0/24 via 192.0.2.9`. A packet for 172.16.40.31 arrives. Which route wins?

  1. The OSPF 172.16.40.0/24 route, because /24 is more specific than /0.
  2. No route matches because the destination is a host, not a network address.
  3. Both routes are used equally for this destination.
  4. The static default, because static AD 1 is lower than OSPF AD 110.

Explanation

Correct Answer

A:

Longest matching prefix selection is performed before AD is relevant for the same prefix; /24 matches more specifically than /0.

Incorrect Answers

B:

The destination host is contained in the 172.16.40.0/24 route.

C:

Equal-cost multipath requires qualifying equal destinations and route metrics, not a /0 versus /24.

D:

Administrative distance is not compared across routes with different prefix lengths for forwarding lookup.

Question 582

At a warehouse distribution floor, SW2 must enable single-area OSPFv2 on interfaces within 172.18.20.0/24, all in area 0. Which IOS configuration matches the IPv4 network?

  1. router ospf 1; network 172.18.20.0 0.0.0.255 area 1
  2. router ospf 1; network 172.18.20.0 255.255.255.0 area 0
  3. router ospf 1; network 0.0.0.0 0.0.0.0 area 0
  4. router ospf 1; network 172.18.20.0 0.0.0.255 area 0

Explanation

Correct Answer

D:

OSPFv2 network commands use a wildcard (inverse subnet mask) and an intended area; the specified /24 is placed in area 0.

Incorrect Answers

A:

The requested design is area 0, whereas this places the interface in area 1.

B:

The IOS network command expects a wildcard mask, not the dotted subnet mask.

C:

A zero wildcard with 0.0.0.0 matches only an interface with that exact IP, not the intended /24.

Question 583

An OSPFv2 engineer at an enterprise data center must set router R2 to unique router ID 10.10.4.1. Which process-level command is required?

  1. router ospf 2; network 10.10.4.1 255.255.255.255 area 0
  2. interface vlan 27; router-id 10.10.4.1
  3. router ospf 2; router-id 10.10.4.1
  4. router ospf 2; router-id 0.0.0.0

Explanation

Correct Answer

C:

An explicit router-id statement under the local OSPF process sets the intended unique 32-bit identifier, potentially requiring process restart to take effect.

Incorrect Answers

A:

Adding a network statement does not set the router-id explicitly.

B:

Router ID is an OSPF process-level setting, not an SVI subcommand.

D:

An all-zero router ID is not the requested identity.

Question 584

At a disaster-recovery location, ACCESS2 sees its peer OSPF HELLO traffic on the wire but never reaches FULL. The routers have mismatched area IDs and hello timers. What must be aligned?

  1. Give neighbors different area IDs and rely on route redistributions
  2. Match OSPF area, compatible hello/dead timers and Layer 3 subnet parameters between peers
  3. Configure one side as OSPF area 0 and the other as area 1 on the same link
  4. Disable OSPF on the interface and expect a FULL state

Explanation

Correct Answer

B:

OSPF neighbors need compatible adjacency parameters including area, interface subnet and hello/dead interval settings.

Incorrect Answers

A:

Different OSPF areas on the same peering link prevent an ordinary OSPF adjacency.

C:

Area mismatches are an explicit adjacency blocker.

D:

A passive or disabled OSPF interface will not form new OSPF adjacencies.

Question 585

BR-RT routes VLAN 41 for end-user laptops at a regional healthcare office. The LAN prefix must be advertised into single-area OSPFv2, but the switch-facing client segment must not form OSPF neighbors. Which setting fits?

  1. Configure a new router-id on each employee laptop
  2. Send OSPF Hellos to all untrusted hosts on that VLAN
  3. Disable OSPF globally so all routes disappear
  4. Use passive-interface on the user LAN while advertising its connected IPv4 prefix

Explanation

Correct Answer

D:

OSPF passive-interface suppresses adjacencies on that interface but can still advertise the connected network.

Incorrect Answers

A:

End hosts do not need OSPF router identifiers for ordinary client networking.

B:

Hellos toward untrusted hosts are precisely what the passive interface seeks to suppress.

C:

Disabling OSPF removes dynamic routing rather than isolating adjacency formation on one interface.

Question 586

On a new OSPFv2 broadcast segment at a municipal library, three routers have interface DR priorities 0, 1 and 50. Router IDs differ. Which eligible router becomes DR assuming a fresh election?

  1. The router with priority 0 is elected DR because it waits longest
  2. The eligible router with priority 50 becomes DR in a fresh election
  3. The router with priority 1 always beats 50 regardless of router ID
  4. The DR is elected by the numerically highest OSPF process ID

Explanation

Correct Answer

B:

For a new broadcast-network DR election, a higher OSPF interface priority wins; a priority-0 router is ineligible.

Incorrect Answers

A:

Priority 0 makes an OSPF router ineligible to become DR or BDR.

C:

A lower nonzero interface priority loses to a higher one in a fresh election.

D:

OSPF process IDs are local and not DR-election attributes.

Question 587

Two routers are joined by a dedicated point-to-point link using OSPFv2 area 0 at a hospitality property. What special DR behavior is expected?

  1. The interface becomes a multiaccess Ethernet broadcast segment automatically
  2. No DR/BDR election occurs on a point-to-point OSPF network
  3. A point-to-point link must elect one DR and one BDR
  4. A DR is always elected based on largest interface speed

Explanation

Correct Answer

B:

OSPF point-to-point network type needs no designated router election between the two adjacent nodes.

Incorrect Answers

A:

A point-to-point OSPF network type does not become broadcast multiaccess merely by using Ethernet hardware.

C:

DR/BDR are used on broadcast and certain nonbroadcast multiaccess types, not normal point-to-point.

D:

Interface link speed is not a mechanism to elect DR on point-to-point networks.

Question 588

At a remote field office, two OSPFv2 routers are both DROTHER on a broadcast VLAN and show 2-WAY to each other, while both show FULL with the DR. What does this mean?

  1. A DROTHER router must be elected DR by forcing a process reboot
  2. The absence of FULL between any two routers means the segment cannot carry routes
  3. Two DROTHER routers can remain in 2-WAY with each other while both are FULL with the DR/BDR
  4. All DROTHER peers must be FULL with one another on broadcast Ethernet

Explanation

Correct Answer

C:

On a broadcast network, DROTHERs form full adjacencies mainly with the DR and BDR; their mutual relationship can be 2-WAY.

Incorrect Answers

A:

A router reboot is neither necessary nor desirable for an expected neighbor relationship.

B:

2-WAY is an expected neighbor relationship among DROTHER peers and does not automatically indicate a fault.

D:

DROTHER-to-DROTHER full adjacency is not mandatory on the normal broadcast model.

Question 589

SW1 has two OSPFv2 neighbors on a service-provider edge and an engineer needs to verify their router IDs and FULL/2-WAY states. Which IOS show command is appropriate?

  1. show ip ospf neighbor
  2. show mac address-table dynamic
  3. show ip nat translations
  4. show vlan brief

Explanation

Correct Answer

A:

show ip ospf neighbor displays OSPFv2 neighbors, their states and peer router IDs.

Incorrect Answers

B:

The Ethernet MAC table does not show OSPF adjacency states.

C:

NAT translation tables are unrelated to OSPF peering.

D:

VLAN membership output cannot confirm FULL or 2-WAY OSPF neighbor states.

Question 590

At a training network, one Cisco router uses router ospf 10 and its peer uses router ospf 200. All required OSPFv2 adjacency settings match. Does the process-number mismatch prevent peering?

  1. A different process number forces one router to use OSPFv3 instead
  2. Process ID values define each OSPF area ID on the wire
  3. Neighbors must have exactly the same local process number to exchange LSAs
  4. OSPF process IDs are locally significant and do not need to match on neighboring routers

Explanation

Correct Answer

D:

In Cisco IOS the router ospf process number is local; area and adjacency parameters matter between peers.

Incorrect Answers

A:

OSPFv2/v3 selection is not determined by arbitrary local process number differences.

B:

OSPF area ID is configured independently of the local process ID.

C:

The local process IDs are not carried as a matching neighbor parameter.