McAfee-Secured Website

Exam Bundle

Exam Code: 200-301

Exam Name Cisco Certified Network Associate (CCNA)

Certification Provider: Cisco

Corresponding Certification: CCNA

Cisco 200-301 Bundle $44.99

100% Cisco 200-301 Guaranteed Success With Testking Training Materials

Get Real 200-301 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

  • Questions & Answers

    200-301 Questions & Answers

    760 Questions & Answers

    The ultimate exam preparation tool, Questions & Answers mirrors the actual 200-301 exam while allowing you to hone and measure every aspect of your test-taking ability.

  • 200-301 Video Course

    200-301 Video Course

    271 Video Lectures

    200-301 Video Course is developed by Cisco Professionals to help you pass the 200-301 exam.

    Description

    This course will improve your knowledge and skills required to pass Cisco Certified Network Associate (CCNA) exam.
  • Study Guide

    200-301 Study Guide

    1969 PDF Pages

    Developed by industry experts, this 1969-page guide spells out in painstaking detail all of the information you need to ace 200-301 exam.

Cisco Certified Network Associate (CCNA) (200-301) Practice Tests

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Total Cost: $194.97
Bundle Price: $149.98

Purchase Individually

  • Questions & Answers

    Questions & Answers

    760 Questions

    $124.99
  • 200-301 Video Course

    Video Course

    271 Video Lectures

    $39.99
  • Study Guide

    Study Guide

    1969 PDF Pages

    $29.99

Cisco 200-301 Practice Test 35

Question 340

A campus wants SW-A root for VLAN 10 and SW-B root for VLAN 20 to distribute uplink forwarding. Which spanning-tree design fits Rapid PVST+?

  1. Change the first-hop gateway address to determine every VLAN root.
  2. Use one common bridge priority for all VLANs and expect automatic alternating roots.
  3. Disable spanning tree on one VLAN to force load balancing.
  4. Assign a lower bridge priority to SW-A for VLAN 10 and to SW-B for VLAN 20.

Explanation

Correct Answer

D:

Rapid PVST+ has separate STP instances per VLAN, allowing intentional root bridge placement by VLAN-specific priority.

Incorrect Answers

A:

First-hop IP gateway selection is separate from the Layer 2 root bridge election.

B:

Equal priorities do not guarantee alternating winners and may lead to MAC-based roots.

C:

Disabling STP exposes redundant Layer 2 paths to loops rather than managing load.

Question 341

DIST2 should be the standby spanning-tree root for VLAN 170 if the preferred primary root is unavailable. Which Cisco IOS macro matches the intended role?

  1. spanning-tree vlan 170 portfast
  2. spanning-tree vlan 170 root secondary
  3. ip ospf priority 170
  4. switchport access vlan 170

Explanation

Correct Answer

B:

The root secondary macro configures a lower priority suited to standby root placement.

Incorrect Answers

A:

PortFast controls host-edge transition, not backup bridge root preference.

C:

OSPF interface priority selects a routing DR on a multiaccess segment, not an STP root.

D:

An access VLAN assignment does not set bridge priority.

Question 342

`show spanning-tree inconsistentports` lists a blocked alternate port as loop-inconsistent. What is the most relevant underlying event to investigate?

  1. An LACP channel-group received a new description.
  2. Expected BPDUs stopped arriving on a protected non-designated port.
  3. The switch was given an additional IPv6 DNS server.
  4. An unrelated route received a lower OSPF metric.

Explanation

Correct Answer

B:

Loop guard enforces a nonforwarding state when a port that normally should receive BPDUs loses them.

Incorrect Answers

A:

A description change has no implication of missing spanning-tree BPDUs.

C:

Client DNS settings are unrelated to incoming STP control frames.

D:

OSPF cost changes do not by themselves create STP loop-inconsistent state.

Question 343

SW-CORE is intended to remain VLAN 100 root and an access switch connects below it. Where should root guard be applied to stop an access switch from usurping root?

  1. On an upstream OSPF interface running the default route.
  2. On SW-CORE designated ports facing potentially untrusted downstream switches.
  3. On the core switch root port toward the intended root bridge.
  4. Only on Ethernet host NICs.

Explanation

Correct Answer

B:

Root guard belongs on designated ports where superior BPDUs from downstream are unexpected.

Incorrect Answers

A:

OSPF default routing has no STP root bridge priority significance.

C:

The intended root bridge does not have a root port; root guard should not be misapplied to a root-facing port.

D:

Host NICs do not provide the Cisco STP root guard configuration.

Question 344

A non-root switch has two equal-cost uplinks to the same upstream bridge, which advertises identical root path cost on both links. All upstream BID factors tie, but sender ports are 128.5 and 128.7. Which port is preferred?

  1. The link receiving from sender port ID 128.5.
  2. Both must be forwarding root ports.
  3. Neither link may receive a BPDU because a loop exists.
  4. The link receiving from sender port ID 128.7.

Explanation

Correct Answer

A:

When root cost and upstream bridge IDs tie, STP compares sender port ID; the lower ID wins.

Incorrect Answers

B:

One root-port selection avoids redundant simultaneous upstream paths.

C:

Receiving BPDUs on both legitimate parallel links is normal during root-port selection.

D:

The higher sender port ID loses this tie-break.

Question 345

An operator fixes the accidental switch connected to a PortFast/BPDU Guard access port, but the port remains err-disabled. What action can restore it after the fault is removed?

  1. Change the VLAN IP subnet mask only.
  2. Configure a static default route on the PC.
  3. Use an administrative shutdown/no shutdown or configured error-disable recovery.
  4. Disable OSPF dead timers on all routers.

Explanation

Correct Answer

C:

BPDU Guard err-disable recovery requires an enabled recovery mechanism or operator resetting the affected interface.

Incorrect Answers

A:

IP mask changes do not clear an err-disabled switch interface.

B:

A PC default route cannot restore a switch port disabled by STP protection.

D:

OSPF timers do not control a Layer 2 BPDU Guard err-disable event.

Question 346

A hypervisor server connects to a Catalyst switch with an 802.1Q trunk because its virtual NICs use multiple VLANs. The server does not bridge back toward another switch and will never send spanning-tree BPDUs. Which interface-side STP setting is appropriate for rapid host startup without bypassing spanning tree on actual switch uplinks?

  1. Disable spanning tree globally on the user VLANs.
  2. Configure `spanning-tree portfast trunk` only on this verified endpoint-facing trunk, with BPDU Guard according to policy.
  3. Enable loop guard to force immediate forwarding on every interswitch redundant trunk.
  4. Apply root guard to all physical ports so no host traffic can be forwarded.

Explanation

Correct Answer

B:

PortFast trunk is intended for a trusted edge trunk to a host that terminates VLANs and cannot bridge or send BPDUs; it is unsafe on an interswitch uplink.

Incorrect Answers

A:

Disabling spanning tree on all VLANs removes loop prevention from the wider bridged topology, unlike a narrowly scoped trusted edge setting.

C:

Loop guard protects certain non-designated STP ports from unexpected BPDU loss; it is not an endpoint-fast-forward feature.

D:

Root guard prevents superior BPDUs on designated ports; it does not replace an end-host PortFast edge policy.

Question 347

An operator must confirm whether a specific switch is root for VLAN 120 and inspect the selected root ID. Which command is most relevant?

  1. `show ip route 120.0.0.0`
  2. `show ip dhcp snooping binding`
  3. `show spanning-tree vlan 120`
  4. `show interfaces trunk` only

Explanation

Correct Answer

C:

Per-VLAN spanning-tree output reports the root bridge ID, local bridge ID, role and state of relevant ports.

Incorrect Answers

A:

IP routing table entries do not identify the VLAN 120 STP root bridge.

B:

The DHCP snooping binding table tracks IP/MAC lease associations, not STP elections.

D:

Trunk output confirms VLAN carriage but does not list root bridge identity or port roles.

Question 348

Two switches are connected by a full-duplex point-to-point Ethernet interconnect and can process RSTP proposals and agreements. What advantage does this link type provide?

  1. It forces the interconnect to operate as a half-duplex hub.
  2. Fast negotiated convergence with synchronization before designated forwarding.
  3. It automatically creates an OSPF adjacency without IP addresses.
  4. It entirely disables the need to exchange BPDUs.

Explanation

Correct Answer

B:

RSTP proposal/agreement on point-to-point links can transition ports quickly when both ends synchronize safely.

Incorrect Answers

A:

A point-to-point full-duplex link does not become a half-duplex shared collision domain.

C:

Layer 3 OSPF formation is not triggered by RSTP state exchange alone.

D:

Control BPDUs are essential to the RSTP agreement process.

Question 349

A distribution switch previously preferred a 1-Gbps uplink with STP cost 4 over a 100-Mbps uplink with cost 19. The preferred link renegotiates at 10 Mbps and now has a higher cost. What route-choice input changes?

  1. The MAC address of the root bridge automatically.
  2. The VLAN identifier on every frame.
  3. The local port path cost and possibly the selected root-port path.
  4. The IPv4 administrative distance of a static route.

Explanation

Correct Answer

C:

STP path cost reflects link speed/cost configuration; a downgrade can change the minimum total path to the root.

Incorrect Answers

A:

The root bridge MAC does not automatically change when a port renegotiates.

B:

VLAN tagging is not rewritten as a result of link speed changes.

D:

Router administrative distance is unrelated to Layer 2 STP path cost.

Question 350

Four parallel links form a healthy Layer 2 EtherChannel between two switches. For STP path selection, how should the bundle be represented?

  1. As a routed OSPF network instead of a Layer 2 bundle.
  2. As four unrelated VLANs with separate bridge IDs.
  3. As one logical Port-channel spanning-tree interface.
  4. As four independent forwarding ports that STP must all disable.

Explanation

Correct Answer

C:

STP treats an EtherChannel bundle as a single logical port for its role and state decisions.

Incorrect Answers

A:

L2 EtherChannel is still bridged; it is not automatically OSPF routed.

B:

Aggregation does not redefine VLANs or create separate root elections per physical member.

D:

A healthy port channel is aggregated, so STP does not independently block each physical member as four separate links.