McAfee-Secured Website

Exam Code: NGFW-Engineer

Exam Name: Palo Alto Networks Certified Next-Generation Firewall Engineer

Certification Provider: Palo Alto Networks

Corresponding Certification: Palo Alto Networks Certified Next-Generation Firewall Engineer

100% Palo Alto Networks NGFW-Engineer Guaranteed Success With Testking Training Materials

Get Real NGFW-Engineer Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

143 Questions & Answers with Testing Engine

"Palo Alto Networks Certified Next-Generation Firewall Engineer Exam", also known as NGFW-Engineer exam, is a Palo Alto Networks certification exam.

Pass your tests with the always up-to-date NGFW-Engineer Exam Engine. Your NGFW-Engineer training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Palo Alto Networks NGFW-Engineer Practice Test 12

Question 110

At a regional logistics hub in Austin, a monitoring policy causes flapping on occasional packet loss despite healthy service. The change affects shipment planning. What outcome directly proves this configuration works?

  1. Controlled loss of gateway reachability triggers the defined path-failure and HA response
  2. Disconnecting that uplink produces the expected HA event and moves service to the healthy peer
  3. The passive peer takes over after the active unit is isolated and allowed traffic resumes through the surviving unit
  4. Transient missed probes no longer cause an unwanted HA transition, but sustained failure does

Explanation

Correct Answer

D:

At a regional logistics hub in Austin, this verifies the specific link and path monitoring requirement rather than merely recording an intended configuration: Transient missed probes no longer cause an unwanted HA transition, but sustained failure does. The associated implementation is: adjust failure thresholds and probe targets to match the documented tolerance.

Incorrect Answers

A:

The offered observation would confirm the separate intervention: Configure supported HA path monitoring to test the remote target rather than relying only on link state. It measures: Controlled loss of gateway reachability triggers the defined path-failure and HA response. The current link and path monitoring configuration is Adjust failure thresholds and probe targets to match the documented tolerance, and must demonstrate: Transient missed probes no longer cause an unwanted HA transition, but sustained failure does. The two acceptance checks are not interchangeable even though they share a feature area.

B:

The offered observation would confirm the separate intervention: Configure HA link monitoring for the business-critical uplink with an appropriate failure response. It measures: Disconnecting that uplink produces the expected HA event and moves service to the healthy peer. The current link and path monitoring configuration is Adjust failure thresholds and probe targets to match the documented tolerance, and must demonstrate: Transient missed probes no longer cause an unwanted HA transition, but sustained failure does. The two acceptance checks are not interchangeable even though they share a feature area.

C:

That observation measures active/passive ha after this other intervention: Configure active/passive HA with working HA1/HA2 paths and configuration synchronization. Its result is: The passive peer takes over after the active unit is isolated and allowed traffic resumes through the surviving unit. The requested link and path monitoring change is Adjust failure thresholds and probe targets to match the documented tolerance, which must demonstrate: Transient missed probes no longer cause an unwanted HA transition, but sustained failure does. The offered evidence does not validate the specified control.

Question 111

During a scheduled deployment at a cloud engineering group in Seattle, a monitoring policy causes flapping on occasional packet loss despite healthy service. The team is verifying its effect on customer APIs. How should the engineer address the stated constraint?

  1. Configure supported HA path monitoring to test the remote target rather than relying only on link state
  2. Adjust failure thresholds and probe targets to match the documented tolerance
  3. Configure active/passive HA with working HA1/HA2 paths and configuration synchronization
  4. Configure HA link monitoring for the business-critical uplink with an appropriate failure response

Explanation

Correct Answer

B:

At a cloud engineering group in Seattle, this directly addresses link and path monitoring at the described site: Adjust failure thresholds and probe targets to match the documented tolerance. The acceptance check is concrete: transient missed probes no longer cause an unwanted HA transition, but sustained failure does.

Incorrect Answers

A:

The alternative would configure supported HA path monitoring to test the remote target rather than relying only on link state; its own acceptance check is: Controlled loss of gateway reachability triggers the defined path-failure and HA response. Although both choices involve link and path monitoring, this case requires the intervention: Adjust failure thresholds and probe targets to match the documented tolerance. Its required outcome is: Transient missed probes no longer cause an unwanted HA transition, but sustained failure does. The first test could pass while this distinct configuration remains unverified.

C:

The alternative would configure active/passive HA with working HA1/HA2 paths and configuration synchronization to address active/passive ha. Its acceptance test is: The passive peer takes over after the active unit is isolated and allowed traffic resumes through the surviving unit. This case instead requires link and path monitoring, implemented by adjust failure thresholds and probe targets to match the documented tolerance; the deciding test is: Transient missed probes no longer cause an unwanted HA transition, but sustained failure does. The alternate control does not establish the requested outcome.

D:

The alternative would configure HA link monitoring for the business-critical uplink with an appropriate failure response; its own acceptance check is: Disconnecting that uplink produces the expected HA event and moves service to the healthy peer. Although both choices involve link and path monitoring, this case requires the intervention: Adjust failure thresholds and probe targets to match the documented tolerance. Its required outcome is: Transient missed probes no longer cause an unwanted HA transition, but sustained failure does. The first test could pass while this distinct configuration remains unverified.

Question 112

During a scheduled deployment at a cloud engineering group in Seattle, a monitoring policy causes flapping on occasional packet loss despite healthy service. The team is verifying its effect on customer APIs. Which test result best supports completion?

  1. Transient missed probes no longer cause an unwanted HA transition, but sustained failure does
  2. Session sync indicators are healthy and established permitted traffic survives the supported failover test
  3. Disconnecting that uplink produces the expected HA event and moves service to the healthy peer
  4. Controlled loss of gateway reachability triggers the defined path-failure and HA response

Explanation

Correct Answer

A:

At a cloud engineering group in Seattle, this verifies the specific link and path monitoring requirement rather than merely recording an intended configuration: Transient missed probes no longer cause an unwanted HA transition, but sustained failure does. The associated implementation is: adjust failure thresholds and probe targets to match the documented tolerance.

Incorrect Answers

B:

That observation measures active/passive ha after this other intervention: Provide the required HA data synchronization interface/path for the selected platform and mode. Its result is: Session sync indicators are healthy and established permitted traffic survives the supported failover test. The requested link and path monitoring change is Adjust failure thresholds and probe targets to match the documented tolerance, which must demonstrate: Transient missed probes no longer cause an unwanted HA transition, but sustained failure does. The offered evidence does not validate the specified control.

C:

The offered observation would confirm the separate intervention: Configure HA link monitoring for the business-critical uplink with an appropriate failure response. It measures: Disconnecting that uplink produces the expected HA event and moves service to the healthy peer. The current link and path monitoring configuration is Adjust failure thresholds and probe targets to match the documented tolerance, and must demonstrate: Transient missed probes no longer cause an unwanted HA transition, but sustained failure does. The two acceptance checks are not interchangeable even though they share a feature area.

D:

The offered observation would confirm the separate intervention: Configure supported HA path monitoring to test the remote target rather than relying only on link state. It measures: Controlled loss of gateway reachability triggers the defined path-failure and HA response. The current link and path monitoring configuration is Adjust failure thresholds and probe targets to match the documented tolerance, and must demonstrate: Transient missed probes no longer cause an unwanted HA transition, but sustained failure does. The two acceptance checks are not interchangeable even though they share a feature area.

Question 113

At a pharmaceutical warehouse in Raleigh, a branch must exchange changing internal prefixes with a neighboring OSPF router instead of maintaining static routes. The change affects inventory systems. Which adjustment should be part of the approved fix?

  1. Establish BGP neighbors with compatible AS, address family and prefix policies
  2. Review route-selection settings and the installed route rather than assuming all configured routes forward
  3. Assign the interfaces to the appropriate advanced logical router rather than mixing router models
  4. Configure an OSPF adjacency and advertisement on the proper routed interface/router

Explanation

Correct Answer

D:

At a pharmaceutical warehouse in Raleigh, this directly addresses dynamic routing protocols at the described site: Configure an OSPF adjacency and advertisement on the proper routed interface/router. The acceptance check is concrete: the OSPF neighbor is Full and the expected route appears with its learned next hop.

Incorrect Answers

A:

The alternative would establish BGP neighbors with compatible AS, address family and prefix policies; its own acceptance check is: BGP peer reaches Established and only authorized routes are accepted and advertised. Although both choices involve dynamic routing protocols, this case requires the intervention: Configure an OSPF adjacency and advertisement on the proper routed interface/router. Its required outcome is: The OSPF neighbor is Full and the expected route appears with its learned next hop. The first test could pass while this distinct configuration remains unverified.

B:

The alternative would review route-selection settings and the installed route rather than assuming all configured routes forward; its own acceptance check is: The active forwarding entry reflects the intended protocol and administrative preference. Although both choices involve dynamic routing protocols, this case requires the intervention: Configure an OSPF adjacency and advertisement on the proper routed interface/router. Its required outcome is: The OSPF neighbor is Full and the expected route appears with its learned next hop. The first test could pass while this distinct configuration remains unverified.

C:

The alternative would assign the interfaces to the appropriate advanced logical router rather than mixing router models to address advanced routing engine. Its acceptance test is: The interface appears in the actual active logical routing instance and forwarding follows its routes. This case instead requires dynamic routing protocols, implemented by configure an OSPF adjacency and advertisement on the proper routed interface/router; the deciding test is: The OSPF neighbor is Full and the expected route appears with its learned next hop. The alternate control does not establish the requested outcome.

Question 114

At a pharmaceutical warehouse in Raleigh, a branch must exchange changing internal prefixes with a neighboring OSPF router instead of maintaining static routes. The change affects inventory systems. What observed behavior matters most for signoff?

  1. Routes retain intended origin markings and no repeated feedback paths appear during the migration test
  2. The active forwarding entry reflects the intended protocol and administrative preference
  3. BGP peer reaches Established and only authorized routes are accepted and advertised
  4. The OSPF neighbor is Full and the expected route appears with its learned next hop

Explanation

Correct Answer

D:

At a pharmaceutical warehouse in Raleigh, this verifies the specific dynamic routing protocols requirement rather than merely recording an intended configuration: The OSPF neighbor is Full and the expected route appears with its learned next hop. The associated implementation is: configure an OSPF adjacency and advertisement on the proper routed interface/router.

Incorrect Answers

A:

That observation measures redistribution and routing policies after this other intervention: Define direction-specific redistribution controls and route tagging where supported. Its result is: Routes retain intended origin markings and no repeated feedback paths appear during the migration test. The requested dynamic routing protocols change is Configure an OSPF adjacency and advertisement on the proper routed interface/router, which must demonstrate: The OSPF neighbor is Full and the expected route appears with its learned next hop. The offered evidence does not validate the specified control.

B:

The offered observation would confirm the separate intervention: Review route-selection settings and the installed route rather than assuming all configured routes forward. It measures: The active forwarding entry reflects the intended protocol and administrative preference. The current dynamic routing protocols configuration is Configure an OSPF adjacency and advertisement on the proper routed interface/router, and must demonstrate: The OSPF neighbor is Full and the expected route appears with its learned next hop. The two acceptance checks are not interchangeable even though they share a feature area.

C:

The offered observation would confirm the separate intervention: Establish BGP neighbors with compatible AS, address family and prefix policies. It measures: BGP peer reaches Established and only authorized routes are accepted and advertised. The current dynamic routing protocols configuration is Configure an OSPF adjacency and advertisement on the proper routed interface/router, and must demonstrate: The OSPF neighbor is Full and the expected route appears with its learned next hop. The two acceptance checks are not interchangeable even though they share a feature area.

Question 115

During a scheduled deployment at a manufacturer network in Detroit, a branch must exchange changing internal prefixes with a neighboring OSPF router instead of maintaining static routes. The team is verifying its effect on production telemetry. What should the engineer configure first to address this gap?

  1. Apply a scoped redistribution rule and appropriate prefix filtering
  2. Review route-selection settings and the installed route rather than assuming all configured routes forward
  3. Configure an OSPF adjacency and advertisement on the proper routed interface/router
  4. Establish BGP neighbors with compatible AS, address family and prefix policies

Explanation

Correct Answer

C:

At a manufacturer network in Detroit, this directly addresses dynamic routing protocols at the described site: Configure an OSPF adjacency and advertisement on the proper routed interface/router. The acceptance check is concrete: the OSPF neighbor is Full and the expected route appears with its learned next hop.

Incorrect Answers

A:

The alternative would apply a scoped redistribution rule and appropriate prefix filtering to address redistribution and routing policies. Its acceptance test is: Neighbors learn the three permitted prefixes and do not learn unrelated management routes. This case instead requires dynamic routing protocols, implemented by configure an OSPF adjacency and advertisement on the proper routed interface/router; the deciding test is: The OSPF neighbor is Full and the expected route appears with its learned next hop. The alternate control does not establish the requested outcome.

B:

The alternative would review route-selection settings and the installed route rather than assuming all configured routes forward; its own acceptance check is: The active forwarding entry reflects the intended protocol and administrative preference. Although both choices involve dynamic routing protocols, this case requires the intervention: Configure an OSPF adjacency and advertisement on the proper routed interface/router. Its required outcome is: The OSPF neighbor is Full and the expected route appears with its learned next hop. The first test could pass while this distinct configuration remains unverified.

D:

The alternative would establish BGP neighbors with compatible AS, address family and prefix policies; its own acceptance check is: BGP peer reaches Established and only authorized routes are accepted and advertised. Although both choices involve dynamic routing protocols, this case requires the intervention: Configure an OSPF adjacency and advertisement on the proper routed interface/router. Its required outcome is: The OSPF neighbor is Full and the expected route appears with its learned next hop. The first test could pass while this distinct configuration remains unverified.

Question 116

During a scheduled deployment at a manufacturer network in Detroit, a branch must exchange changing internal prefixes with a neighboring OSPF router instead of maintaining static routes. The team is verifying its effect on production telemetry. Which measurement best confirms the intended result?

  1. The OSPF neighbor is Full and the expected route appears with its learned next hop
  2. A simulated upstream failure changes the selected path even when the physical switch port stays up
  3. BGP peer reaches Established and only authorized routes are accepted and advertised
  4. The active forwarding entry reflects the intended protocol and administrative preference

Explanation

Correct Answer

A:

At a manufacturer network in Detroit, this verifies the specific dynamic routing protocols requirement rather than merely recording an intended configuration: The OSPF neighbor is Full and the expected route appears with its learned next hop. The associated implementation is: configure an OSPF adjacency and advertisement on the proper routed interface/router.

Incorrect Answers

B:

That observation measures route monitoring after this other intervention: Monitor a representative reachable target beyond the local handoff. Its result is: A simulated upstream failure changes the selected path even when the physical switch port stays up. The requested dynamic routing protocols change is Configure an OSPF adjacency and advertisement on the proper routed interface/router, which must demonstrate: The OSPF neighbor is Full and the expected route appears with its learned next hop. The offered evidence does not validate the specified control.

C:

The offered observation would confirm the separate intervention: Establish BGP neighbors with compatible AS, address family and prefix policies. It measures: BGP peer reaches Established and only authorized routes are accepted and advertised. The current dynamic routing protocols configuration is Configure an OSPF adjacency and advertisement on the proper routed interface/router, and must demonstrate: The OSPF neighbor is Full and the expected route appears with its learned next hop. The two acceptance checks are not interchangeable even though they share a feature area.

D:

The offered observation would confirm the separate intervention: Review route-selection settings and the installed route rather than assuming all configured routes forward. It measures: The active forwarding entry reflects the intended protocol and administrative preference. The current dynamic routing protocols configuration is Configure an OSPF adjacency and advertisement on the proper routed interface/router, and must demonstrate: The OSPF neighbor is Full and the expected route appears with its learned next hop. The two acceptance checks are not interchangeable even though they share a feature area.

Question 117

At a utility operations center in Phoenix, an enterprise edge must exchange approved prefixes with a provider using BGP rather than OSPF. The change affects control-system reporting. Which action closes the described technical configuration gap?

  1. Configure an OSPF adjacency and advertisement on the proper routed interface/router
  2. Review route-selection settings and the installed route rather than assuming all configured routes forward
  3. Assign the interfaces to the appropriate advanced logical router rather than mixing router models
  4. Establish BGP neighbors with compatible AS, address family and prefix policies

Explanation

Correct Answer

D:

At a utility operations center in Phoenix, this directly addresses dynamic routing protocols at the described site: Establish BGP neighbors with compatible AS, address family and prefix policies. The acceptance check is concrete: bGP peer reaches Established and only authorized routes are accepted and advertised.

Incorrect Answers

A:

The alternative would configure an OSPF adjacency and advertisement on the proper routed interface/router; its own acceptance check is: The OSPF neighbor is Full and the expected route appears with its learned next hop. Although both choices involve dynamic routing protocols, this case requires the intervention: Establish BGP neighbors with compatible AS, address family and prefix policies. Its required outcome is: BGP peer reaches Established and only authorized routes are accepted and advertised. The first test could pass while this distinct configuration remains unverified.

B:

The alternative would review route-selection settings and the installed route rather than assuming all configured routes forward; its own acceptance check is: The active forwarding entry reflects the intended protocol and administrative preference. Although both choices involve dynamic routing protocols, this case requires the intervention: Establish BGP neighbors with compatible AS, address family and prefix policies. Its required outcome is: BGP peer reaches Established and only authorized routes are accepted and advertised. The first test could pass while this distinct configuration remains unverified.

C:

The alternative would assign the interfaces to the appropriate advanced logical router rather than mixing router models to address advanced routing engine. Its acceptance test is: The interface appears in the actual active logical routing instance and forwarding follows its routes. This case instead requires dynamic routing protocols, implemented by establish BGP neighbors with compatible AS, address family and prefix policies; the deciding test is: BGP peer reaches Established and only authorized routes are accepted and advertised. The alternate control does not establish the requested outcome.

Question 118

At a utility operations center in Phoenix, an enterprise edge must exchange approved prefixes with a provider using BGP rather than OSPF. The change affects control-system reporting. What evidence would demonstrate success without relying on a saved setting alone?

  1. The active forwarding entry reflects the intended protocol and administrative preference
  2. The OSPF neighbor is Full and the expected route appears with its learned next hop
  3. Loss of the monitored next hop removes the route and backup forwarding becomes active
  4. BGP peer reaches Established and only authorized routes are accepted and advertised

Explanation

Correct Answer

D:

At a utility operations center in Phoenix, this verifies the specific dynamic routing protocols requirement rather than merely recording an intended configuration: BGP peer reaches Established and only authorized routes are accepted and advertised. The associated implementation is: establish BGP neighbors with compatible AS, address family and prefix policies.

Incorrect Answers

A:

The offered observation would confirm the separate intervention: Review route-selection settings and the installed route rather than assuming all configured routes forward. It measures: The active forwarding entry reflects the intended protocol and administrative preference. The current dynamic routing protocols configuration is Establish BGP neighbors with compatible AS, address family and prefix policies, and must demonstrate: BGP peer reaches Established and only authorized routes are accepted and advertised. The two acceptance checks are not interchangeable even though they share a feature area.

B:

The offered observation would confirm the separate intervention: Configure an OSPF adjacency and advertisement on the proper routed interface/router. It measures: The OSPF neighbor is Full and the expected route appears with its learned next hop. The current dynamic routing protocols configuration is Establish BGP neighbors with compatible AS, address family and prefix policies, and must demonstrate: BGP peer reaches Established and only authorized routes are accepted and advertised. The two acceptance checks are not interchangeable even though they share a feature area.

C:

That observation measures route monitoring after this other intervention: Configure supported route or path monitoring to withdraw the failed static route. Its result is: Loss of the monitored next hop removes the route and backup forwarding becomes active. The requested dynamic routing protocols change is Establish BGP neighbors with compatible AS, address family and prefix policies, which must demonstrate: BGP peer reaches Established and only authorized routes are accepted and advertised. The offered evidence does not validate the specified control.

Question 119

During a scheduled deployment at a mining operations site in Salt Lake City, an enterprise edge must exchange approved prefixes with a provider using BGP rather than OSPF. The team is verifying its effect on sensor telemetry. What configuration decision is supported by the stated facts?

  1. Configure an OSPF adjacency and advertisement on the proper routed interface/router
  2. Establish BGP neighbors with compatible AS, address family and prefix policies
  3. Enable and configure the supported Advanced Routing Engine with a logical router
  4. Review route-selection settings and the installed route rather than assuming all configured routes forward

Explanation

Correct Answer

B:

At a mining operations site in Salt Lake City, this directly addresses dynamic routing protocols at the described site: Establish BGP neighbors with compatible AS, address family and prefix policies. The acceptance check is concrete: bGP peer reaches Established and only authorized routes are accepted and advertised.

Incorrect Answers

A:

The alternative would configure an OSPF adjacency and advertisement on the proper routed interface/router; its own acceptance check is: The OSPF neighbor is Full and the expected route appears with its learned next hop. Although both choices involve dynamic routing protocols, this case requires the intervention: Establish BGP neighbors with compatible AS, address family and prefix policies. Its required outcome is: BGP peer reaches Established and only authorized routes are accepted and advertised. The first test could pass while this distinct configuration remains unverified.

C:

The alternative would enable and configure the supported Advanced Routing Engine with a logical router to address advanced routing engine. Its acceptance test is: The intended interfaces and prefixes appear under the logical router and advanced route policies take effect. This case instead requires dynamic routing protocols, implemented by establish BGP neighbors with compatible AS, address family and prefix policies; the deciding test is: BGP peer reaches Established and only authorized routes are accepted and advertised. The alternate control does not establish the requested outcome.

D:

The alternative would review route-selection settings and the installed route rather than assuming all configured routes forward; its own acceptance check is: The active forwarding entry reflects the intended protocol and administrative preference. Although both choices involve dynamic routing protocols, this case requires the intervention: Establish BGP neighbors with compatible AS, address family and prefix policies. Its required outcome is: BGP peer reaches Established and only authorized routes are accepted and advertised. The first test could pass while this distinct configuration remains unverified.

Question 120

During a scheduled deployment at a mining operations site in Salt Lake City, an enterprise edge must exchange approved prefixes with a provider using BGP rather than OSPF. The team is verifying its effect on sensor telemetry. Which acceptance outcome addresses the precise requirement?

  1. The rejected prefix is absent from the routing table and an approved prefix still installs
  2. The OSPF neighbor is Full and the expected route appears with its learned next hop
  3. BGP peer reaches Established and only authorized routes are accepted and advertised
  4. The active forwarding entry reflects the intended protocol and administrative preference

Explanation

Correct Answer

C:

At a mining operations site in Salt Lake City, this verifies the specific dynamic routing protocols requirement rather than merely recording an intended configuration: BGP peer reaches Established and only authorized routes are accepted and advertised. The associated implementation is: establish BGP neighbors with compatible AS, address family and prefix policies.

Incorrect Answers

A:

That observation measures redistribution and routing policies after this other intervention: Use filtering and route policy to exclude unapproved prefixes before import. Its result is: The rejected prefix is absent from the routing table and an approved prefix still installs. The requested dynamic routing protocols change is Establish BGP neighbors with compatible AS, address family and prefix policies, which must demonstrate: BGP peer reaches Established and only authorized routes are accepted and advertised. The offered evidence does not validate the specified control.

B:

The offered observation would confirm the separate intervention: Configure an OSPF adjacency and advertisement on the proper routed interface/router. It measures: The OSPF neighbor is Full and the expected route appears with its learned next hop. The current dynamic routing protocols configuration is Establish BGP neighbors with compatible AS, address family and prefix policies, and must demonstrate: BGP peer reaches Established and only authorized routes are accepted and advertised. The two acceptance checks are not interchangeable even though they share a feature area.

D:

The offered observation would confirm the separate intervention: Review route-selection settings and the installed route rather than assuming all configured routes forward. It measures: The active forwarding entry reflects the intended protocol and administrative preference. The current dynamic routing protocols configuration is Establish BGP neighbors with compatible AS, address family and prefix policies, and must demonstrate: BGP peer reaches Established and only authorized routes are accepted and advertised. The two acceptance checks are not interchangeable even though they share a feature area.

Palo Alto Networks Certified Next-Generation Firewall Engineer (NGFW-Engineer) Practice Tests