McAfee-Secured Website

Exam Code: JN0-106

Exam Name: Junos, Associate (JNCIA-Junos)

Certification Provider: Juniper

Corresponding Certification: JNCIA-Junos

100% Juniper JN0-106 Guaranteed Success With Testking Training Materials

Get Real JN0-106 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

98 Questions & Answers with Testing Engine

"Junos, Associate (JNCIA-Junos) Exam", also known as JN0-106 exam, is a Juniper certification exam.

Pass your tests with the always up-to-date JN0-106 Exam Engine. Your JN0-106 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Juniper JN0-106 Practice Test 5

Question 40

Within Networking Fundamentals, a technician selects this approach: Plan for 254 ordinary usable IPv4 host addresses in that /24 subnet. Which original requirement or fault would most directly justify it?

  1. A host knows the on-link IPv4 address of a peer but has no Ethernet destination MAC address.
  2. A team must determine the directed broadcast address of the 192.0.2.64/27 subnet.
  3. An IPv4 LAN uses a conventional /24 mask and reserves network and broadcast addresses.
  4. A host must learn which on-link IPv6 router can forward packets to destinations outside its subnet.

Explanation

Correct Answer

C:

A /24 leaves eight host bits, yielding 256 addresses; the all-zero network and all-one broadcast addresses are reserved. This meets the stated need for ipv4 /24 usable hosts.

Incorrect Answers

A:

The ipv4 arp resolution scenario has a different requirement: ARP maps an IPv4 address on a local link to the MAC address used to deliver Ethernet frames. It does not directly meet the ipv4 /24 usable hosts need in this question.

B:

The ipv4 broadcast address scenario has a different requirement: A /27 spans 32 addresses, so the .64 subnet ends with the all-host-bits-one address .95. It does not directly meet the ipv4 /24 usable hosts need in this question.

D:

The ipv6 default-router discovery scenario has a different requirement: IPv6 Router Advertisements carry default-router information that hosts can use for off-link forwarding. It does not directly meet the ipv4 /24 usable hosts need in this question.

Question 41

A network engineer must choose a subnet with 30 ordinary IPv4 host addresses. Which configuration or troubleshooting action most directly meets the need?

  1. Configure its switchport as an access port in the finance VLAN.
  2. Allocate an IPv4 /27 subnet for the 30-host segment.
  3. Use valid FE80::/10 link-local IPv6 addresses on the local segment.
  4. Use ICMPv6 Neighbor Solicitation and Neighbor Advertisement rather than IPv4 ARP.

Explanation

Correct Answer

B:

A /27 has five host bits and 32 total addresses, of which 30 are ordinary usable hosts. This meets the stated need for ipv4 /27 usable hosts.

Incorrect Answers

A:

The access-port vlan assignment scenario has a different requirement: An access port associates untagged endpoint traffic with one configured VLAN instead of requiring the host to add tags. It does not directly meet the ipv4 /27 usable hosts need in this question.

C:

The ipv6 link-local scope scenario has a different requirement: IPv6 link-local unicast addresses are for local-link communication and are not routed across ordinary routers. It does not directly meet the ipv4 /27 usable hosts need in this question.

D:

The ipv6 neighbor discovery scenario has a different requirement: IPv6 Neighbor Discovery replaces ARP with ICMPv6 messages for neighbor address resolution. It does not directly meet the ipv4 /27 usable hosts need in this question.

Question 42

Within Networking Fundamentals, a Junos engineer proposes the following response: Allocate an IPv4 /27 subnet for the 30-host segment. Which concept or operating procedure is best illustrated?

  1. IPv4 /27 usable hosts
  2. Access-port VLAN assignment
  3. IPv6 link-local scope
  4. IPv6 neighbor discovery

Explanation

Correct Answer

A:

A /27 has five host bits and 32 total addresses, of which 30 are ordinary usable hosts. This meets the stated need for ipv4 /27 usable hosts.

Incorrect Answers

B:

The access-port vlan assignment scenario has a different requirement: An access port associates untagged endpoint traffic with one configured VLAN instead of requiring the host to add tags. It does not directly meet the ipv4 /27 usable hosts need in this question.

C:

The ipv6 link-local scope scenario has a different requirement: IPv6 link-local unicast addresses are for local-link communication and are not routed across ordinary routers. It does not directly meet the ipv4 /27 usable hosts need in this question.

D:

The ipv6 neighbor discovery scenario has a different requirement: IPv6 Neighbor Discovery replaces ARP with ICMPv6 messages for neighbor address resolution. It does not directly meet the ipv4 /27 usable hosts need in this question.

Question 43

A network engineer must choose a subnet with 30 ordinary IPv4 host addresses. The proposed response is: Allocate an IPv4 /27 subnet for the 30-host segment. Which explanation most accurately supports this response?

  1. An access port associates untagged endpoint traffic with one configured VLAN instead of requiring the host to add tags.
  2. IPv6 link-local unicast addresses are for local-link communication and are not routed across ordinary routers.
  3. A /27 has five host bits and 32 total addresses, of which 30 are ordinary usable hosts.
  4. IPv6 Neighbor Discovery replaces ARP with ICMPv6 messages for neighbor address resolution.

Explanation

Correct Answer

C:

A /27 has five host bits and 32 total addresses, of which 30 are ordinary usable hosts. This meets the stated need for ipv4 /27 usable hosts.

Incorrect Answers

A:

The access-port vlan assignment scenario has a different requirement: An access port associates untagged endpoint traffic with one configured VLAN instead of requiring the host to add tags. It does not directly meet the ipv4 /27 usable hosts need in this question.

B:

The ipv6 link-local scope scenario has a different requirement: IPv6 link-local unicast addresses are for local-link communication and are not routed across ordinary routers. It does not directly meet the ipv4 /27 usable hosts need in this question.

D:

The ipv6 neighbor discovery scenario has a different requirement: IPv6 Neighbor Discovery replaces ARP with ICMPv6 messages for neighbor address resolution. It does not directly meet the ipv4 /27 usable hosts need in this question.

Question 44

Within Networking Fundamentals, a technician selects this approach: Allocate an IPv4 /27 subnet for the 30-host segment. Which original requirement or fault would most directly justify it?

  1. A network engineer must choose a subnet with 30 ordinary IPv4 host addresses.
  2. An ordinary workstation sends untagged frames and must be assigned to the finance broadcast domain.
  3. Two routers on the same Ethernet segment exchange IPv6 neighbor messages without globally routable addresses.
  4. An IPv6 host needs the MAC address associated with a neighbor's on-link IPv6 address.

Explanation

Correct Answer

A:

A /27 has five host bits and 32 total addresses, of which 30 are ordinary usable hosts. This meets the stated need for ipv4 /27 usable hosts.

Incorrect Answers

B:

The access-port vlan assignment scenario has a different requirement: An access port associates untagged endpoint traffic with one configured VLAN instead of requiring the host to add tags. It does not directly meet the ipv4 /27 usable hosts need in this question.

C:

The ipv6 link-local scope scenario has a different requirement: IPv6 link-local unicast addresses are for local-link communication and are not routed across ordinary routers. It does not directly meet the ipv4 /27 usable hosts need in this question.

D:

The ipv6 neighbor discovery scenario has a different requirement: IPv6 Neighbor Discovery replaces ARP with ICMPv6 messages for neighbor address resolution. It does not directly meet the ipv4 /27 usable hosts need in this question.

Question 45

A legacy IPv4 point-to-point link requires exactly two conventional usable host addresses. Which configuration or troubleshooting action most directly meets the need?

  1. Use ICMPv6 Neighbor Solicitation and Neighbor Advertisement rather than IPv4 ARP.
  2. Configure a VLAN-tagged 802.1Q trunk with the intended VLAN membership on both ends.
  3. Map traffic into appropriate egress queues and configure a suitable class-of-service scheduler.
  4. Assign a /30 subnet with the two middle IPv4 addresses to the routers.

Explanation

Correct Answer

D:

A conventional /30 has four addresses, with network and broadcast reserved and two usable host addresses. This meets the stated need for ipv4 /30 point-to-point.

Incorrect Answers

A:

The ipv6 neighbor discovery scenario has a different requirement: IPv6 Neighbor Discovery replaces ARP with ICMPv6 messages for neighbor address resolution. It does not directly meet the ipv4 /30 point-to-point need in this question.

B:

The ieee 802.1q trunking scenario has a different requirement: 802.1Q VLAN tags identify the logical Layer 2 segment carried over a shared physical link. It does not directly meet the ipv4 /30 point-to-point need in this question.

C:

The cos scheduling queues scenario has a different requirement: CoS queuing and scheduling influence which packets receive transmission opportunity during congestion. It does not directly meet the ipv4 /30 point-to-point need in this question.

Question 46

Within Networking Fundamentals, a Junos engineer proposes the following response: Assign a /30 subnet with the two middle IPv4 addresses to the routers. Which concept or operating procedure is best illustrated?

  1. IPv6 neighbor discovery
  2. IPv4 /30 point-to-point
  3. IEEE 802.1Q trunking
  4. CoS scheduling queues

Explanation

Correct Answer

B:

A conventional /30 has four addresses, with network and broadcast reserved and two usable host addresses. This meets the stated need for ipv4 /30 point-to-point.

Incorrect Answers

A:

The ipv6 neighbor discovery scenario has a different requirement: IPv6 Neighbor Discovery replaces ARP with ICMPv6 messages for neighbor address resolution. It does not directly meet the ipv4 /30 point-to-point need in this question.

C:

The ieee 802.1q trunking scenario has a different requirement: 802.1Q VLAN tags identify the logical Layer 2 segment carried over a shared physical link. It does not directly meet the ipv4 /30 point-to-point need in this question.

D:

The cos scheduling queues scenario has a different requirement: CoS queuing and scheduling influence which packets receive transmission opportunity during congestion. It does not directly meet the ipv4 /30 point-to-point need in this question.

Question 47

A legacy IPv4 point-to-point link requires exactly two conventional usable host addresses. The proposed response is: Assign a /30 subnet with the two middle IPv4 addresses to the routers. Which explanation most accurately supports this response?

  1. IPv6 Neighbor Discovery replaces ARP with ICMPv6 messages for neighbor address resolution.
  2. 802.1Q VLAN tags identify the logical Layer 2 segment carried over a shared physical link.
  3. A conventional /30 has four addresses, with network and broadcast reserved and two usable host addresses.
  4. CoS queuing and scheduling influence which packets receive transmission opportunity during congestion.

Explanation

Correct Answer

C:

A conventional /30 has four addresses, with network and broadcast reserved and two usable host addresses. This meets the stated need for ipv4 /30 point-to-point.

Incorrect Answers

A:

The ipv6 neighbor discovery scenario has a different requirement: IPv6 Neighbor Discovery replaces ARP with ICMPv6 messages for neighbor address resolution. It does not directly meet the ipv4 /30 point-to-point need in this question.

B:

The ieee 802.1q trunking scenario has a different requirement: 802.1Q VLAN tags identify the logical Layer 2 segment carried over a shared physical link. It does not directly meet the ipv4 /30 point-to-point need in this question.

D:

The cos scheduling queues scenario has a different requirement: CoS queuing and scheduling influence which packets receive transmission opportunity during congestion. It does not directly meet the ipv4 /30 point-to-point need in this question.

Question 48

Within Networking Fundamentals, a technician selects this approach: Assign a /30 subnet with the two middle IPv4 addresses to the routers. Which original requirement or fault would most directly justify it?

  1. A legacy IPv4 point-to-point link requires exactly two conventional usable host addresses.
  2. An IPv6 host needs the MAC address associated with a neighbor's on-link IPv6 address.
  3. A single Ethernet uplink must carry user traffic belonging to three separate VLANs.
  4. A router must prefer delay-sensitive traffic without allowing background transfers to monopolize the egress link.

Explanation

Correct Answer

A:

A conventional /30 has four addresses, with network and broadcast reserved and two usable host addresses. This meets the stated need for ipv4 /30 point-to-point.

Incorrect Answers

B:

The ipv6 neighbor discovery scenario has a different requirement: IPv6 Neighbor Discovery replaces ARP with ICMPv6 messages for neighbor address resolution. It does not directly meet the ipv4 /30 point-to-point need in this question.

C:

The ieee 802.1q trunking scenario has a different requirement: 802.1Q VLAN tags identify the logical Layer 2 segment carried over a shared physical link. It does not directly meet the ipv4 /30 point-to-point need in this question.

D:

The cos scheduling queues scenario has a different requirement: CoS queuing and scheduling influence which packets receive transmission opportunity during congestion. It does not directly meet the ipv4 /30 point-to-point need in this question.

Question 49

A server uses address 192.0.2.143 with a /26 prefix and needs its correct subnet identifier. Which configuration or troubleshooting action most directly meets the need?

  1. Identify the containing network as 192.0.2.128/26.
  2. Configure its switchport as an access port in the finance VLAN.
  3. Allocate an IPv4 /27 subnet for the 30-host segment.
  4. Allow the switch to learn the source MAC address and ingress port from frames sent by that host.

Explanation

Correct Answer

A:

A /26 advances in blocks of 64 in the last octet, so.143 lies inside the.128 through.191 subnet. This meets the stated need for ipv4 /26 network boundary.

Incorrect Answers

B:

The access-port vlan assignment scenario has a different requirement: An access port associates untagged endpoint traffic with one configured VLAN instead of requiring the host to add tags. It does not directly meet the ipv4 /26 network boundary need in this question.

C:

The ipv4 /27 usable hosts scenario has a different requirement: A /27 has five host bits and 32 total addresses, of which 30 are ordinary usable hosts. It does not directly meet the ipv4 /26 network boundary need in this question.

D:

The ethernet source-mac learning scenario has a different requirement: Ethernet switches populate their forwarding database from source MAC addresses observed on ingress frames. It does not directly meet the ipv4 /26 network boundary need in this question.

Question 50

Within Networking Fundamentals, a Junos engineer proposes the following response: Identify the containing network as 192.0.2.128/26. Which concept or operating procedure is best illustrated?

  1. Access-port VLAN assignment
  2. IPv4 /26 network boundary
  3. IPv4 /27 usable hosts
  4. Ethernet source-MAC learning

Explanation

Correct Answer

B:

A /26 advances in blocks of 64 in the last octet, so.143 lies inside the.128 through.191 subnet. This meets the stated need for ipv4 /26 network boundary.

Incorrect Answers

A:

The access-port vlan assignment scenario has a different requirement: An access port associates untagged endpoint traffic with one configured VLAN instead of requiring the host to add tags. It does not directly meet the ipv4 /26 network boundary need in this question.

C:

The ipv4 /27 usable hosts scenario has a different requirement: A /27 has five host bits and 32 total addresses, of which 30 are ordinary usable hosts. It does not directly meet the ipv4 /26 network boundary need in this question.

D:

The ethernet source-mac learning scenario has a different requirement: Ethernet switches populate their forwarding database from source MAC addresses observed on ingress frames. It does not directly meet the ipv4 /26 network boundary need in this question.

Junos, Associate (JNCIA-Junos) (JN0-106) Practice Tests