McAfee-Secured Website

Exam Code: JN0-106

Exam Name: Junos, Associate (JNCIA-Junos)

Certification Provider: Juniper

Corresponding Certification: JNCIA-Junos

100% Juniper JN0-106 Guaranteed Success With Testking Training Materials

Get Real JN0-106 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

98 Questions & Answers with Testing Engine

"Junos, Associate (JNCIA-Junos) Exam", also known as JN0-106 exam, is a Juniper certification exam.

Pass your tests with the always up-to-date JN0-106 Exam Engine. Your JN0-106 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Juniper JN0-106 Practice Test 3

Question 20

Within Networking Fundamentals, a technician selects this approach: Expect unknown unicast frames to be flooded within the VLAN until the destination MAC is learned. Which original requirement or fault would most directly justify it?

  1. A new Ethernet destination MAC address is absent from a switch's forwarding table.
  2. A large packet repeatedly fails across a link with an MTU smaller than its total size.
  3. A packet capture shows SYN, SYN-ACK, and ACK before payload exchange.
  4. A branch router has no more specific route for a public destination but has an upstream Internet gateway.

Explanation

Correct Answer

A:

A bridge cannot select one outgoing port for an unknown destination, so it floods eligible ports in that broadcast domain. This meets the stated need for unknown-unicast flooding.

Incorrect Answers

B:

The ipv4 packet mtu scenario has a different requirement: An MTU constrains the maximum packet carried by a link, so oversized packets require compatible handling. It does not directly meet the unknown-unicast flooding need in this question.

C:

The tcp three-way handshake scenario has a different requirement: The SYN, SYN-ACK, and ACK exchange synchronizes sequence numbers when a TCP connection is established. It does not directly meet the unknown-unicast flooding need in this question.

D:

The ipv4 default route scenario has a different requirement: The IPv4 default route matches any destination without a more-specific active prefix. It does not directly meet the unknown-unicast flooding need in this question.

Question 21

A host knows the on-link IPv4 address of a peer but has no Ethernet destination MAC address. Which configuration or troubleshooting action most directly meets the need?

  1. Use ARP resolution to learn the peer's link-layer address before sending the Ethernet frame.
  2. Use an active 0.0.0.0/0 default route toward the upstream gateway.
  3. Replace the repeater with a switch that provides a separate collision domain for each full-duplex port.
  4. Convert decimal 13 to 00001101 in eight-bit binary notation.

Explanation

Correct Answer

A:

ARP maps an IPv4 address on a local link to the MAC address used to deliver Ethernet frames. This meets the stated need for ipv4 arp resolution.

Incorrect Answers

B:

The ipv4 default route scenario has a different requirement: The IPv4 default route matches any destination without a more-specific active prefix. It does not directly meet the ipv4 arp resolution need in this question.

C:

The collision-domain isolation scenario has a different requirement: A switch separates contention at each port, whereas a hub repeats traffic into one shared collision domain. It does not directly meet the ipv4 arp resolution need in this question.

D:

The decimal to binary conversion scenario has a different requirement: Thirteen equals eight plus four plus one, so the 8, 4, and 1 bit positions are set. It does not directly meet the ipv4 arp resolution need in this question.

Question 22

Within Networking Fundamentals, a Junos engineer proposes the following response: Use ARP resolution to learn the peer's link-layer address before sending the Ethernet frame. Which concept or operating procedure is best illustrated?

  1. IPv4 default route
  2. IPv4 ARP resolution
  3. Collision-domain isolation
  4. Decimal to binary conversion

Explanation

Correct Answer

B:

ARP maps an IPv4 address on a local link to the MAC address used to deliver Ethernet frames. This meets the stated need for ipv4 arp resolution.

Incorrect Answers

A:

The ipv4 default route scenario has a different requirement: The IPv4 default route matches any destination without a more-specific active prefix. It does not directly meet the ipv4 arp resolution need in this question.

C:

The collision-domain isolation scenario has a different requirement: A switch separates contention at each port, whereas a hub repeats traffic into one shared collision domain. It does not directly meet the ipv4 arp resolution need in this question.

D:

The decimal to binary conversion scenario has a different requirement: Thirteen equals eight plus four plus one, so the 8, 4, and 1 bit positions are set. It does not directly meet the ipv4 arp resolution need in this question.

Question 23

A host knows the on-link IPv4 address of a peer but has no Ethernet destination MAC address. The proposed response is: Use ARP resolution to learn the peer's link-layer address before sending the Ethernet frame. Which explanation most accurately supports this response?

  1. The IPv4 default route matches any destination without a more-specific active prefix.
  2. ARP maps an IPv4 address on a local link to the MAC address used to deliver Ethernet frames.
  3. A switch separates contention at each port, whereas a hub repeats traffic into one shared collision domain.
  4. Thirteen equals eight plus four plus one, so the 8, 4, and 1 bit positions are set.

Explanation

Correct Answer

B:

ARP maps an IPv4 address on a local link to the MAC address used to deliver Ethernet frames. This meets the stated need for ipv4 arp resolution.

Incorrect Answers

A:

The ipv4 default route scenario has a different requirement: The IPv4 default route matches any destination without a more-specific active prefix. It does not directly meet the ipv4 arp resolution need in this question.

C:

The collision-domain isolation scenario has a different requirement: A switch separates contention at each port, whereas a hub repeats traffic into one shared collision domain. It does not directly meet the ipv4 arp resolution need in this question.

D:

The decimal to binary conversion scenario has a different requirement: Thirteen equals eight plus four plus one, so the 8, 4, and 1 bit positions are set. It does not directly meet the ipv4 arp resolution need in this question.

Question 24

Within Networking Fundamentals, a technician selects this approach: Use ARP resolution to learn the peer's link-layer address before sending the Ethernet frame. Which original requirement or fault would most directly justify it?

  1. A branch router has no more specific route for a public destination but has an upstream Internet gateway.
  2. A host knows the on-link IPv4 address of a peer but has no Ethernet destination MAC address.
  3. A campus Ethernet link connects several hosts through an old shared repeater, and simultaneous transmissions cause collisions.
  4. An addressing exercise asks for the eight-bit unsigned binary representation of decimal 13.

Explanation

Correct Answer

B:

ARP maps an IPv4 address on a local link to the MAC address used to deliver Ethernet frames. This meets the stated need for ipv4 arp resolution.

Incorrect Answers

A:

The ipv4 default route scenario has a different requirement: The IPv4 default route matches any destination without a more-specific active prefix. It does not directly meet the ipv4 arp resolution need in this question.

C:

The collision-domain isolation scenario has a different requirement: A switch separates contention at each port, whereas a hub repeats traffic into one shared collision domain. It does not directly meet the ipv4 arp resolution need in this question.

D:

The decimal to binary conversion scenario has a different requirement: Thirteen equals eight plus four plus one, so the 8, 4, and 1 bit positions are set. It does not directly meet the ipv4 arp resolution need in this question.

Question 25

An IPv6 host needs the MAC address associated with a neighbor's on-link IPv6 address. Which configuration or troubleshooting action most directly meets the need?

  1. Plan for 254 ordinary usable IPv4 host addresses in that /24 subnet.
  2. Configure its switchport as an access port in the finance VLAN.
  3. Use ICMPv6 Neighbor Solicitation and Neighbor Advertisement rather than IPv4 ARP.
  4. Place the departments in separate VLANs and route between them only where policy permits.

Explanation

Correct Answer

C:

IPv6 Neighbor Discovery replaces ARP with ICMPv6 messages for neighbor address resolution. This meets the stated need for ipv6 neighbor discovery.

Incorrect Answers

A:

The ipv4 /24 usable hosts scenario has a different requirement: A /24 leaves eight host bits, yielding 256 addresses; the all-zero network and all-one broadcast addresses are reserved. It does not directly meet the ipv6 neighbor discovery need in this question.

B:

The access-port vlan assignment scenario has a different requirement: An access port associates untagged endpoint traffic with one configured VLAN instead of requiring the host to add tags. It does not directly meet the ipv6 neighbor discovery need in this question.

D:

The broadcast-domain boundary scenario has a different requirement: Each VLAN is a distinct Layer 2 broadcast domain; a router or Layer 3 interface is needed to cross that boundary. It does not directly meet the ipv6 neighbor discovery need in this question.

Question 26

Within Networking Fundamentals, a Junos engineer proposes the following response: Use ICMPv6 Neighbor Solicitation and Neighbor Advertisement rather than IPv4 ARP. Which concept or operating procedure is best illustrated?

  1. IPv4 /24 usable hosts
  2. Access-port VLAN assignment
  3. IPv6 neighbor discovery
  4. Broadcast-domain boundary

Explanation

Correct Answer

C:

IPv6 Neighbor Discovery replaces ARP with ICMPv6 messages for neighbor address resolution. This meets the stated need for ipv6 neighbor discovery.

Incorrect Answers

A:

The ipv4 /24 usable hosts scenario has a different requirement: A /24 leaves eight host bits, yielding 256 addresses; the all-zero network and all-one broadcast addresses are reserved. It does not directly meet the ipv6 neighbor discovery need in this question.

B:

The access-port vlan assignment scenario has a different requirement: An access port associates untagged endpoint traffic with one configured VLAN instead of requiring the host to add tags. It does not directly meet the ipv6 neighbor discovery need in this question.

D:

The broadcast-domain boundary scenario has a different requirement: Each VLAN is a distinct Layer 2 broadcast domain; a router or Layer 3 interface is needed to cross that boundary. It does not directly meet the ipv6 neighbor discovery need in this question.

Question 27

An IPv6 host needs the MAC address associated with a neighbor's on-link IPv6 address. The proposed response is: Use ICMPv6 Neighbor Solicitation and Neighbor Advertisement rather than IPv4 ARP. Which explanation most accurately supports this response?

  1. A /24 leaves eight host bits, yielding 256 addresses; the all-zero network and all-one broadcast addresses are reserved.
  2. IPv6 Neighbor Discovery replaces ARP with ICMPv6 messages for neighbor address resolution.
  3. An access port associates untagged endpoint traffic with one configured VLAN instead of requiring the host to add tags.
  4. Each VLAN is a distinct Layer 2 broadcast domain; a router or Layer 3 interface is needed to cross that boundary.

Explanation

Correct Answer

B:

IPv6 Neighbor Discovery replaces ARP with ICMPv6 messages for neighbor address resolution. This meets the stated need for ipv6 neighbor discovery.

Incorrect Answers

A:

The ipv4 /24 usable hosts scenario has a different requirement: A /24 leaves eight host bits, yielding 256 addresses; the all-zero network and all-one broadcast addresses are reserved. It does not directly meet the ipv6 neighbor discovery need in this question.

C:

The access-port vlan assignment scenario has a different requirement: An access port associates untagged endpoint traffic with one configured VLAN instead of requiring the host to add tags. It does not directly meet the ipv6 neighbor discovery need in this question.

D:

The broadcast-domain boundary scenario has a different requirement: Each VLAN is a distinct Layer 2 broadcast domain; a router or Layer 3 interface is needed to cross that boundary. It does not directly meet the ipv6 neighbor discovery need in this question.

Question 28

Within Networking Fundamentals, a technician selects this approach: Use ICMPv6 Neighbor Solicitation and Neighbor Advertisement rather than IPv4 ARP. Which original requirement or fault would most directly justify it?

  1. An IPv4 LAN uses a conventional /24 mask and reserves network and broadcast addresses.
  2. An ordinary workstation sends untagged frames and must be assigned to the finance broadcast domain.
  3. Two departments on the same switching fabric must not receive one another's Layer 2 broadcast traffic.
  4. An IPv6 host needs the MAC address associated with a neighbor's on-link IPv6 address.

Explanation

Correct Answer

D:

IPv6 Neighbor Discovery replaces ARP with ICMPv6 messages for neighbor address resolution. This meets the stated need for ipv6 neighbor discovery.

Incorrect Answers

A:

The ipv4 /24 usable hosts scenario has a different requirement: A /24 leaves eight host bits, yielding 256 addresses; the all-zero network and all-one broadcast addresses are reserved. It does not directly meet the ipv6 neighbor discovery need in this question.

B:

The access-port vlan assignment scenario has a different requirement: An access port associates untagged endpoint traffic with one configured VLAN instead of requiring the host to add tags. It does not directly meet the ipv6 neighbor discovery need in this question.

C:

The broadcast-domain boundary scenario has a different requirement: Each VLAN is a distinct Layer 2 broadcast domain; a router or Layer 3 interface is needed to cross that boundary. It does not directly meet the ipv6 neighbor discovery need in this question.

Question 29

A single Ethernet uplink must carry user traffic belonging to three separate VLANs. Which configuration or troubleshooting action most directly meets the need?

  1. Allow the switch to learn the source MAC address and ingress port from frames sent by that host.
  2. Configure a VLAN-tagged 802.1Q trunk with the intended VLAN membership on both ends.
  3. Identify the subnet mask as a /25 prefix.
  4. Use destination MAC FF:FF:FF:FF:FF:FF for a Layer 2 broadcast frame.

Explanation

Correct Answer

B:

802.1Q VLAN tags identify the logical Layer 2 segment carried over a shared physical link. This meets the stated need for ieee 802.1q trunking.

Incorrect Answers

A:

The ethernet source-mac learning scenario has a different requirement: Ethernet switches populate their forwarding database from source MAC addresses observed on ingress frames. It does not directly meet the ieee 802.1q trunking need in this question.

C:

The subnet mask /25 interpretation scenario has a different requirement: The first 25 mask bits are set to one: 24 bits in the first three octets and one more in 128. It does not directly meet the ieee 802.1q trunking need in this question.

D:

The ethernet broadcast destination scenario has a different requirement: The all-ones Ethernet destination address denotes a broadcast received throughout the local VLAN. It does not directly meet the ieee 802.1q trunking need in this question.

Question 30

Within Networking Fundamentals, a Junos engineer proposes the following response: Configure a VLAN-tagged 802.1Q trunk with the intended VLAN membership on both ends. Which concept or operating procedure is best illustrated?

  1. IEEE 802.1Q trunking
  2. Ethernet source-MAC learning
  3. Subnet mask /25 interpretation
  4. Ethernet broadcast destination

Explanation

Correct Answer

A:

802.1Q VLAN tags identify the logical Layer 2 segment carried over a shared physical link. This meets the stated need for ieee 802.1q trunking.

Incorrect Answers

B:

The ethernet source-mac learning scenario has a different requirement: Ethernet switches populate their forwarding database from source MAC addresses observed on ingress frames. It does not directly meet the ieee 802.1q trunking need in this question.

C:

The subnet mask /25 interpretation scenario has a different requirement: The first 25 mask bits are set to one: 24 bits in the first three octets and one more in 128. It does not directly meet the ieee 802.1q trunking need in this question.

D:

The ethernet broadcast destination scenario has a different requirement: The all-ones Ethernet destination address denotes a broadcast received throughout the local VLAN. It does not directly meet the ieee 802.1q trunking need in this question.

Junos, Associate (JNCIA-Junos) (JN0-106) Practice Tests