McAfee-Secured Website

Exam Code: JN0-106

Exam Name: Junos, Associate (JNCIA-Junos)

Certification Provider: Juniper

Corresponding Certification: JNCIA-Junos

100% Juniper JN0-106 Guaranteed Success With Testking Training Materials

Get Real JN0-106 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

98 Questions & Answers with Testing Engine

"Junos, Associate (JNCIA-Junos) Exam", also known as JN0-106 exam, is a Juniper certification exam.

Pass your tests with the always up-to-date JN0-106 Exam Engine. Your JN0-106 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Juniper JN0-106 Practice Test 108

Question 1070

Within Routing Policy and Firewall Filters, a Junos engineer proposes the following response: Apply the intended firewall filter in the interface's output direction. Which concept or operating procedure is best illustrated?

  1. Policy match protocol
  2. Unicast RPF strict mode
  3. Firewall source-address match
  4. Egress firewall filter

Explanation

Correct Answer

D:

An output filter evaluates eligible packets on egress rather than at ingress. This meets the stated need for egress firewall filter.

Incorrect Answers

A:

The policy match protocol scenario has a different requirement: The from protocol match selects routes based on their protocol origin. It does not directly meet the egress firewall filter need in this question.

B:

The unicast rpf strict mode scenario has a different requirement: Strict uRPF checks whether the routing table's return path to the source points back through the packet's ingress interface. It does not directly meet the egress firewall filter need in this question.

C:

The firewall source-address match scenario has a different requirement: A source-address condition evaluates the source IP field of matching packets. It does not directly meet the egress firewall filter need in this question.

Question 1071

A traffic policy should classify or restrict packets as they leave the interface toward a downstream network. The proposed response is: Apply the intended firewall filter in the interface's output direction. Which explanation most accurately supports this response?

  1. An output filter evaluates eligible packets on egress rather than at ingress.
  2. The from protocol match selects routes based on their protocol origin.
  3. Strict uRPF checks whether the routing table's return path to the source points back through the packet's ingress interface.
  4. A source-address condition evaluates the source IP field of matching packets.

Explanation

Correct Answer

A:

An output filter evaluates eligible packets on egress rather than at ingress. This meets the stated need for egress firewall filter.

Incorrect Answers

B:

The policy match protocol scenario has a different requirement: The from protocol match selects routes based on their protocol origin. It does not directly meet the egress firewall filter need in this question.

C:

The unicast rpf strict mode scenario has a different requirement: Strict uRPF checks whether the routing table's return path to the source points back through the packet's ingress interface. It does not directly meet the egress firewall filter need in this question.

D:

The firewall source-address match scenario has a different requirement: A source-address condition evaluates the source IP field of matching packets. It does not directly meet the egress firewall filter need in this question.

Question 1072

Within Routing Policy and Firewall Filters, a technician selects this approach: Apply the intended firewall filter in the interface's output direction. Which original requirement or fault would most directly justify it?

  1. An export policy must treat static routes differently from OSPF-learned routes.
  2. An ingress interface should reject packets whose source would not be reached through that same best return interface.
  3. An ingress IPv4 filter should act only on packets from 192.0.2.0/24.
  4. A traffic policy should classify or restrict packets as they leave the interface toward a downstream network.

Explanation

Correct Answer

D:

An output filter evaluates eligible packets on egress rather than at ingress. This meets the stated need for egress firewall filter.

Incorrect Answers

A:

The policy match protocol scenario has a different requirement: The from protocol match selects routes based on their protocol origin. It does not directly meet the egress firewall filter need in this question.

B:

The unicast rpf strict mode scenario has a different requirement: Strict uRPF checks whether the routing table's return path to the source points back through the packet's ingress interface. It does not directly meet the egress firewall filter need in this question.

C:

The firewall source-address match scenario has a different requirement: A source-address condition evaluates the source IP field of matching packets. It does not directly meet the egress firewall filter need in this question.

Question 1073

A team copied an IPv4-only family inet filter but needs to inspect IPv6 packets. Which configuration or troubleshooting action most directly meets the need?

  1. Use then reject for that term in the appropriate import or export policy.
  2. Use then accept in the matching firewall filter term.
  3. Apply a carefully designed input firewall filter to the lo0 interface as supported.
  4. Create and attach an appropriate family inet6 firewall filter for IPv6 traffic.

Explanation

Correct Answer

D:

IPv6 packet filtering uses family inet6 rather than assuming an IPv4 family inet filter covers both protocols. This meets the stated need for ipv6 firewall filter family.

Incorrect Answers

A:

The policy then reject scenario has a different requirement: A reject action terminates policy processing for that route with a negative decision. It does not directly meet the ipv6 firewall filter family need in this question.

B:

The firewall filter accept action scenario has a different requirement: Accept permits the matching packet through that filter's evaluation. It does not directly meet the ipv6 firewall filter family need in this question.

C:

The protect routing engine lo0 scenario has a different requirement: A loopback input filter can protect traffic destined for the Routing Engine while preserving required protocol exchanges. It does not directly meet the ipv6 firewall filter family need in this question.

Question 1074

Within Routing Policy and Firewall Filters, a Junos engineer proposes the following response: Create and attach an appropriate family inet6 firewall filter for IPv6 traffic. Which concept or operating procedure is best illustrated?

  1. Policy then reject
  2. Firewall filter accept action
  3. Protect Routing Engine lo0
  4. IPv6 firewall filter family

Explanation

Correct Answer

D:

IPv6 packet filtering uses family inet6 rather than assuming an IPv4 family inet filter covers both protocols. This meets the stated need for ipv6 firewall filter family.

Incorrect Answers

A:

The policy then reject scenario has a different requirement: A reject action terminates policy processing for that route with a negative decision. It does not directly meet the ipv6 firewall filter family need in this question.

B:

The firewall filter accept action scenario has a different requirement: Accept permits the matching packet through that filter's evaluation. It does not directly meet the ipv6 firewall filter family need in this question.

C:

The protect routing engine lo0 scenario has a different requirement: A loopback input filter can protect traffic destined for the Routing Engine while preserving required protocol exchanges. It does not directly meet the ipv6 firewall filter family need in this question.

Question 1075

A team copied an IPv4-only family inet filter but needs to inspect IPv6 packets. The proposed response is: Create and attach an appropriate family inet6 firewall filter for IPv6 traffic. Which explanation most accurately supports this response?

  1. A reject action terminates policy processing for that route with a negative decision.
  2. Accept permits the matching packet through that filter's evaluation.
  3. IPv6 packet filtering uses family inet6 rather than assuming an IPv4 family inet filter covers both protocols.
  4. A loopback input filter can protect traffic destined for the Routing Engine while preserving required protocol exchanges.

Explanation

Correct Answer

C:

IPv6 packet filtering uses family inet6 rather than assuming an IPv4 family inet filter covers both protocols. This meets the stated need for ipv6 firewall filter family.

Incorrect Answers

A:

The policy then reject scenario has a different requirement: A reject action terminates policy processing for that route with a negative decision. It does not directly meet the ipv6 firewall filter family need in this question.

B:

The firewall filter accept action scenario has a different requirement: Accept permits the matching packet through that filter's evaluation. It does not directly meet the ipv6 firewall filter family need in this question.

D:

The protect routing engine lo0 scenario has a different requirement: A loopback input filter can protect traffic destined for the Routing Engine while preserving required protocol exchanges. It does not directly meet the ipv6 firewall filter family need in this question.

Question 1076

Within Routing Policy and Firewall Filters, a technician selects this approach: Create and attach an appropriate family inet6 firewall filter for IPv6 traffic. Which original requirement or fault would most directly justify it?

  1. A route matched by a deny term must be excluded from the intended routing exchange.
  2. Traffic matching a trusted monitoring source should pass the interface's configured packet filter.
  3. A team copied an IPv4-only family inet filter but needs to inspect IPv6 packets.
  4. A router's management and routing-protocol traffic should be restricted to approved control-plane sources.

Explanation

Correct Answer

C:

IPv6 packet filtering uses family inet6 rather than assuming an IPv4 family inet filter covers both protocols. This meets the stated need for ipv6 firewall filter family.

Incorrect Answers

A:

The policy then reject scenario has a different requirement: A reject action terminates policy processing for that route with a negative decision. It does not directly meet the ipv6 firewall filter family need in this question.

B:

The firewall filter accept action scenario has a different requirement: Accept permits the matching packet through that filter's evaluation. It does not directly meet the ipv6 firewall filter family need in this question.

D:

The protect routing engine lo0 scenario has a different requirement: A loopback input filter can protect traffic destined for the Routing Engine while preserving required protocol exchanges. It does not directly meet the ipv6 firewall filter family need in this question.

Question 1077

A router's management and routing-protocol traffic should be restricted to approved control-plane sources. Which configuration or troubleshooting action most directly meets the need?

  1. Create and attach an appropriate family inet6 firewall filter for IPv6 traffic.
  2. Use then discard in the matching firewall filter term.
  3. Apply a carefully designed input firewall filter to the lo0 interface as supported.
  4. Set the appropriate BGP local-preference in a matching policy term.

Explanation

Correct Answer

C:

A loopback input filter can protect traffic destined for the Routing Engine while preserving required protocol exchanges. This meets the stated need for protect routing engine lo0.

Incorrect Answers

A:

The ipv6 firewall filter family scenario has a different requirement: IPv6 packet filtering uses family inet6 rather than assuming an IPv4 family inet filter covers both protocols. It does not directly meet the protect routing engine lo0 need in this question.

B:

The firewall filter discard action scenario has a different requirement: Discard drops matched packets without explicitly returning an unreachable response. It does not directly meet the protect routing engine lo0 need in this question.

D:

The policy local preference action scenario has a different requirement: BGP local preference influences route choice within an autonomous system without being a generic Ethernet filter. It does not directly meet the protect routing engine lo0 need in this question.

Question 1078

Within Routing Policy and Firewall Filters, a Junos engineer proposes the following response: Apply a carefully designed input firewall filter to the lo0 interface as supported. Which concept or operating procedure is best illustrated?

  1. IPv6 firewall filter family
  2. Firewall filter discard action
  3. Policy local preference action
  4. Protect Routing Engine lo0

Explanation

Correct Answer

D:

A loopback input filter can protect traffic destined for the Routing Engine while preserving required protocol exchanges. This meets the stated need for protect routing engine lo0.

Incorrect Answers

A:

The ipv6 firewall filter family scenario has a different requirement: IPv6 packet filtering uses family inet6 rather than assuming an IPv4 family inet filter covers both protocols. It does not directly meet the protect routing engine lo0 need in this question.

B:

The firewall filter discard action scenario has a different requirement: Discard drops matched packets without explicitly returning an unreachable response. It does not directly meet the protect routing engine lo0 need in this question.

C:

The policy local preference action scenario has a different requirement: BGP local preference influences route choice within an autonomous system without being a generic Ethernet filter. It does not directly meet the protect routing engine lo0 need in this question.

Question 1079

A router's management and routing-protocol traffic should be restricted to approved control-plane sources. The proposed response is: Apply a carefully designed input firewall filter to the lo0 interface as supported. Which explanation most accurately supports this response?

  1. IPv6 packet filtering uses family inet6 rather than assuming an IPv4 family inet filter covers both protocols.
  2. Discard drops matched packets without explicitly returning an unreachable response.
  3. A loopback input filter can protect traffic destined for the Routing Engine while preserving required protocol exchanges.
  4. BGP local preference influences route choice within an autonomous system without being a generic Ethernet filter.

Explanation

Correct Answer

C:

A loopback input filter can protect traffic destined for the Routing Engine while preserving required protocol exchanges. This meets the stated need for protect routing engine lo0.

Incorrect Answers

A:

The ipv6 firewall filter family scenario has a different requirement: IPv6 packet filtering uses family inet6 rather than assuming an IPv4 family inet filter covers both protocols. It does not directly meet the protect routing engine lo0 need in this question.

B:

The firewall filter discard action scenario has a different requirement: Discard drops matched packets without explicitly returning an unreachable response. It does not directly meet the protect routing engine lo0 need in this question.

D:

The policy local preference action scenario has a different requirement: BGP local preference influences route choice within an autonomous system without being a generic Ethernet filter. It does not directly meet the protect routing engine lo0 need in this question.

Question 1080

Within Routing Policy and Firewall Filters, a technician selects this approach: Apply a carefully designed input firewall filter to the lo0 interface as supported. Which original requirement or fault would most directly justify it?

  1. A team copied an IPv4-only family inet filter but needs to inspect IPv6 packets.
  2. A stateless ingress policy should silently drop a known unwanted traffic class.
  3. An incoming BGP route should receive a different local preference for internal path selection.
  4. A router's management and routing-protocol traffic should be restricted to approved control-plane sources.

Explanation

Correct Answer

D:

A loopback input filter can protect traffic destined for the Routing Engine while preserving required protocol exchanges. This meets the stated need for protect routing engine lo0.

Incorrect Answers

A:

The ipv6 firewall filter family scenario has a different requirement: IPv6 packet filtering uses family inet6 rather than assuming an IPv4 family inet filter covers both protocols. It does not directly meet the protect routing engine lo0 need in this question.

B:

The firewall filter discard action scenario has a different requirement: Discard drops matched packets without explicitly returning an unreachable response. It does not directly meet the protect routing engine lo0 need in this question.

C:

The policy local preference action scenario has a different requirement: BGP local preference influences route choice within an autonomous system without being a generic Ethernet filter. It does not directly meet the protect routing engine lo0 need in this question.

Junos, Associate (JNCIA-Junos) (JN0-106) Practice Tests