McAfee-Secured Website

Exam Bundle

Exam Code: 200-301

Exam Name Cisco Certified Network Associate (CCNA)

Certification Provider: Cisco

Corresponding Certification: CCNA

Cisco 200-301 Bundle $44.99

100% Cisco 200-301 Guaranteed Success With Testking Training Materials

Get Real 200-301 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

  • Questions & Answers

    200-301 Questions & Answers

    760 Questions & Answers

    The ultimate exam preparation tool, Questions & Answers mirrors the actual 200-301 exam while allowing you to hone and measure every aspect of your test-taking ability.

  • 200-301 Video Course

    200-301 Video Course

    271 Video Lectures

    200-301 Video Course is developed by Cisco Professionals to help you pass the 200-301 exam.

    Description

    This course will improve your knowledge and skills required to pass Cisco Certified Network Associate (CCNA) exam.
  • Study Guide

    200-301 Study Guide

    1969 PDF Pages

    Developed by industry experts, this 1969-page guide spells out in painstaking detail all of the information you need to ace 200-301 exam.

Cisco Certified Network Associate (CCNA) (200-301) Practice Tests

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Total Cost: $194.97
Bundle Price: $149.98

Purchase Individually

  • Questions & Answers

    Questions & Answers

    760 Questions

    $124.99
  • 200-301 Video Course

    Video Course

    271 Video Lectures

    $39.99
  • Study Guide

    Study Guide

    1969 PDF Pages

    $29.99

Cisco 200-301 Practice Test 31

Question 300

A Layer 2 EtherChannel is configured with three member links. Two members are trunks, but the third was changed to access mode. What change addresses the inconsistent bundle?

  1. Rename the interface description to match the other ports
  2. Assign the third member an unrelated routed IPv4 address
  3. Align the third member switchport trunk characteristics with the port-channel members
  4. Enable a separate DHCP relay on the third physical member

Explanation

Correct Answer

C:

All Layer 2 bundle members need compatible switchport type and VLAN trunk parameters.

Incorrect Answers

A:

Description strings are not bundle compatibility parameters.

B:

Adding a routed interface makes it incompatible with the existing Layer 2 trunk bundle.

D:

DHCP relay does not reconcile EtherChannel Layer 2 mode mismatch.

Question 301

The EtherChannel summary shows one physical link with flag `(s)` rather than `(P)`, and the logical channel has only one active member. What does the lowercase s indicate?

  1. The port has been selected as the DHCP snooping trust uplink
  2. The member is forwarding as the sole STP root port
  3. The member is successfully bundled and passing traffic
  4. The member is suspended and not currently bundled

Explanation

Correct Answer

D:

A suspended interface is excluded from the working EtherChannel, often because of a compatibility problem.

Incorrect Answers

A:

DHCP snooping trust has a separate interface configuration, unrelated to this flag.

B:

STP root-port status is not represented by the EtherChannel member s flag.

C:

A bundled member is normally flagged P, not s.

Question 302

A router and switch are to form a dynamically negotiated EtherChannel that checks peer agreement before aggregating links. Which channel-group mode matches the request?

  1. auto
  2. desirable
  3. on
  4. active

Explanation

Correct Answer

D:

Active enables LACP negotiation of a dynamic port-channel with an LACP peer.

Incorrect Answers

A:

Auto is associated with PAgP rather than initiating LACP negotiation.

B:

Desirable initiates PAgP, not LACP on the interface.

C:

Static on forces aggregation without negotiating compatibility through LACP.

Question 303

An uplink EtherChannel is configured LACP active on one switch and PAgP desirable on the other. Both members remain individual. Which change addresses the underlying problem?

  1. Increase STP root priority on both switches
  2. Use LACP-compatible modes on both peers, such as active and passive
  3. Set one side to `mode on` and leave the other as PAgP desirable
  4. Make member interface descriptions identical

Explanation

Correct Answer

B:

LACP and PAgP are distinct negotiation protocols and will not establish a dynamic bundle together.

Incorrect Answers

A:

STP root election does not align EtherChannel negotiation protocols.

C:

Static bundling on one side does not negotiate PAgP safely with its neighbor.

D:

Text descriptions do not substitute for matching link aggregation protocol.

Question 304

A Cisco IOS switch reports `Po5(RU)` under Port-channel in `show etherchannel summary`, with member interfaces `Gi1/0/1(P)` and `Gi1/0/2(P)`. What can the operator conclude from these status flags?

  1. The port-channel is a Layer 2 trunk that is down because of STP.
  2. The routed port-channel exists but is not in use.
  3. The two physical ports are independent and not bundled.
  4. The Layer 3 port-channel is in use and both physical members are bundled.

Explanation

Correct Answer

D:

The summary flags define R as Layer 3, U as in use, and P as bundled, exactly matching the active two-member routed EtherChannel.

Incorrect Answers

A:

R means a routed Layer 3 channel, not an S-flagged Layer 2 channel; the U flag also contradicts an out-of-use state.

B:

RU includes U for in use, so this interpretation incorrectly turns an active Layer 3 bundle into a down/inactive one.

C:

P on each physical member identifies a port bundled in the channel; stand-alone members would instead use I.

Question 305

A two-member LACP trunk should carry VLANs 21 and 22. One member permits 21 only and the other permits both; the platform suspends the inconsistent link. What should the technician do?

  1. Leave the individual member VLAN list different for per-flow load balancing.
  2. Make allowed VLAN and trunk settings consistent with the logical bundle before restoring the member.
  3. Change OSPF priority on the upstream router to repair the trunk bundle.
  4. Use port security on the suspended interswitch trunk to override the inconsistency.

Explanation

Correct Answer

B:

Member trunk compatibility must agree with the Port-channel configuration; conflicting allowed VLAN lists prevent stable bundling on platforms enforcing consistency.

Incorrect Answers

A:

Different allowed-VLAN lists do not serve as an EtherChannel load-distribution policy.

C:

OSPF priority affects routing DR election, not a physical switch bundle mismatch.

D:

Port security does not reconcile EtherChannel member trunk configuration.

Question 306

An engineering team intends Port-channel5 as a routed point-to-point LACP uplink. Member ports have been assigned to channel-group 5, but the Port-channel itself is still configured as a Layer 2 switchport. What configuration change addresses the Layer 3 prerequisite?

  1. Set a data access VLAN on the Port-channel and add a native VLAN.
  2. Assign the IPv4 /30 independently to each physical member while keeping the channel switched.
  3. Make the logical Port-channel routed with `no switchport`, ensure members are compatible routed interfaces, then assign the routed address on Port-channel5.
  4. Enable PortFast on the physical member links to convert the Port-channel to routed mode.

Explanation

Correct Answer

C:

A routed Port-channel requires Layer 3 mode, with physical members configured compatibly and the IP address assigned to the logical aggregate.

Incorrect Answers

A:

Access/native VLAN membership keeps the aggregate at Layer 2 and does not create a routed point-to-point interface.

B:

A Layer 3 EtherChannel owns its IP configuration at the logical Port-channel; independently numbering members defeats the intended routed bundle.

D:

PortFast affects spanning-tree transitions on Layer 2 links; it does not change a switchport into a routed EtherChannel.

Question 307

In the LACP `show etherchannel summary` output, Po9 is `(SU)`, Gi1/0/1 is `(P)`, and Gi1/0/2 is `(H)`. The operator expects only one link to carry traffic while the other is held as protection. How should the H flag be interpreted?

  1. The second member is operating at half duplex and must be removed.
  2. The second member is already a second independent forwarding Port-channel.
  3. The second member is in LACP hot-standby, not actively bundled for forwarding.
  4. Both member links are being routed by OSPF instead of participating in LACP.

Explanation

Correct Answer

C:

Cisco show EtherChannel flags use H for a hot-standby LACP member, which can provide redundancy without being in the active bundle.

Incorrect Answers

A:

H is a LACP hot-standby indicator, not an Ethernet duplex indicator; speed and duplex are inspected through interface status.

B:

An H-flagged physical member is not another logical Port-channel, and P on the first link is the currently bundled member.

D:

SU identifies a switched Layer 2 aggregate in use; neither H nor P indicates any OSPF route-selection behavior.

Question 308

After configuring LACP, `show etherchannel summary` reports `Po12(SU)` with `Gi1/0/1(P)` and `Gi1/0/2(P)`. Which interpretation is supported?

  1. The Layer 2 port-channel is up and both listed interfaces are bundled members.
  2. Both interfaces are individually routed links outside the bundle.
  3. The port channel is down due to incompatible VLAN modes.
  4. The switch has created an OSPF neighbor on each link.

Explanation

Correct Answer

A:

The SU combination indicates a Layer 2 in-use bundle, while member (P) flags identify ports participating in the port-channel.

Incorrect Answers

B:

Individual links would typically appear with I flags rather than P.

C:

SU and both P flags contradict a down or unusable bundle state.

D:

EtherChannel flags do not report OSPF adjacency formation.

Question 309

A technician runs `show etherchannel summary` and sees `Po7(SU)` with a member shown as `(P)`. What does the member `(P)` flag indicate?

  1. The port is acting as the spanning-tree root bridge
  2. The physical member is bundled in the port-channel
  3. The member has been suspended because of parameter mismatch
  4. The member is administratively shutdown

Explanation

Correct Answer

B:

Cisco’s P flag marks a port as successfully participating in its channel bundle.

Incorrect Answers

A:

A member flag is not a spanning-tree root designation.

C:

Suspended members are shown separately rather than as bundled P members.

D:

An administratively down interface would not be a participating bundled member.

Question 310

A four-member EtherChannel load-balances using only the destination IP. Hundreds of different clients connect to one busy backup server IP and consistently overload one member while the others are idle. On a switch supporting alternative hash inputs, which change can spread distinct client flows more effectively?

  1. Use a supported source-and-destination IP hash and verify the distribution across the actual client addresses.
  2. Disable all three spare members so aggregate capacity equals a single link.
  3. Force the switch to round-robin individual packets of the same TCP session across all member links.
  4. Configure a different STP root bridge on every packet sent to that server.

Explanation

Correct Answer

A:

With destination-only hashing, all sessions to the same server share one hash input; incorporating variable client source IPs can distribute those distinct flows among members, although balance is not guaranteed.

Incorrect Answers

B:

Disabling healthy members reduces resilience and capacity rather than improving distribution across the existing bundle.

C:

Per-packet striping of one TCP session is not the normal EtherChannel flow-hashing behavior and risks packet reordering.

D:

Spanning-tree bridge elections do not select an EtherChannel member for each unicast packet; the member-selection hash does.