McAfee-Secured Website

Exam Code: JN0-106

Exam Name: Junos, Associate (JNCIA-Junos)

Certification Provider: Juniper

Corresponding Certification: JNCIA-Junos

100% Juniper JN0-106 Guaranteed Success With Testking Training Materials

Get Real JN0-106 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

98 Questions & Answers with Testing Engine

"Junos, Associate (JNCIA-Junos) Exam", also known as JN0-106 exam, is a Juniper certification exam.

Pass your tests with the always up-to-date JN0-106 Exam Engine. Your JN0-106 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Juniper JN0-106 Practice Test 79

Question 780

Within Operational Monitoring and Maintenance, a technician selects this approach: Run show interfaces descriptions or inspect the configured interface description. Which original requirement or fault would most directly justify it?

  1. A packet-level mismatch requires inspecting traffic as it enters an interface on a lab device.
  2. A technician needs to identify the remote peer of an uplink using locally documented labels.
  3. Traffic appears to take the wrong route and an engineer wants to see active destination routes.
  4. A post-upgrade step requires restarting a Junos router under an approved maintenance plan.

Explanation

Correct Answer

B:

Interface descriptions provide human-maintained connectivity hints alongside live link status. This meets the stated need for inspect interface description.

Incorrect Answers

A:

The capture interface packets scenario has a different requirement: Packet capture can reveal protocol headers and observed packet direction for troubleshooting. It does not directly meet the inspect interface description need in this question.

C:

The inspect routing table scenario has a different requirement: Show route exposes route destinations, protocol origins, preference, and next-hop information. It does not directly meet the inspect interface description need in this question.

D:

The controlled device reboot scenario has a different requirement: The reboot operation restarts the system and must be coordinated to manage service interruption. It does not directly meet the inspect interface description need in this question.

Question 781

A technician needs to inspect ordinary unicast IPv4 routes in the default routing instance. Which configuration or troubleshooting action most directly meets the need?

  1. Configure an appropriate static discard route for that aggregate.
  2. Restore the interface's operational state and recheck its connected route.
  3. Inspect the inet.0 routing table with show route table inet.0.
  4. Run ping with the appropriate routing-instance context where the CLI supports it.

Explanation

Correct Answer

C:

The default Junos IPv4 unicast RIB is normally named inet.0. This meets the stated need for default ipv4 routing table.

Incorrect Answers

A:

The static route discard action scenario has a different requirement: A static discard next hop silently drops matching traffic and can provide an aggregation safety route. It does not directly meet the default ipv4 routing table need in this question.

B:

The interface-down connected route scenario has a different requirement: Direct routes depend on their configured interfaces being operational and participating in routing. It does not directly meet the default ipv4 routing table need in this question.

D:

The routing instance ping scenario has a different requirement: Testing from the correct routing instance uses that instance's routing context rather than the default table. It does not directly meet the default ipv4 routing table need in this question.

Question 782

Within Routing Fundamentals, a Junos engineer proposes the following response: Inspect the inet.0 routing table with show route table inet.0. Which concept or operating procedure is best illustrated?

  1. Static route discard action
  2. Default IPv4 routing table
  3. Interface-down connected route
  4. Routing instance ping

Explanation

Correct Answer

B:

The default Junos IPv4 unicast RIB is normally named inet.0. This meets the stated need for default ipv4 routing table.

Incorrect Answers

A:

The static route discard action scenario has a different requirement: A static discard next hop silently drops matching traffic and can provide an aggregation safety route. It does not directly meet the default ipv4 routing table need in this question.

C:

The interface-down connected route scenario has a different requirement: Direct routes depend on their configured interfaces being operational and participating in routing. It does not directly meet the default ipv4 routing table need in this question.

D:

The routing instance ping scenario has a different requirement: Testing from the correct routing instance uses that instance's routing context rather than the default table. It does not directly meet the default ipv4 routing table need in this question.

Question 783

A technician needs to inspect ordinary unicast IPv4 routes in the default routing instance. The proposed response is: Inspect the inet.0 routing table with show route table inet.0. Which explanation most accurately supports this response?

  1. A static discard next hop silently drops matching traffic and can provide an aggregation safety route.
  2. Direct routes depend on their configured interfaces being operational and participating in routing.
  3. The default Junos IPv4 unicast RIB is normally named inet.0.
  4. Testing from the correct routing instance uses that instance's routing context rather than the default table.

Explanation

Correct Answer

C:

The default Junos IPv4 unicast RIB is normally named inet.0. This meets the stated need for default ipv4 routing table.

Incorrect Answers

A:

The static route discard action scenario has a different requirement: A static discard next hop silently drops matching traffic and can provide an aggregation safety route. It does not directly meet the default ipv4 routing table need in this question.

B:

The interface-down connected route scenario has a different requirement: Direct routes depend on their configured interfaces being operational and participating in routing. It does not directly meet the default ipv4 routing table need in this question.

D:

The routing instance ping scenario has a different requirement: Testing from the correct routing instance uses that instance's routing context rather than the default table. It does not directly meet the default ipv4 routing table need in this question.

Question 784

Within Routing Fundamentals, a technician selects this approach: Inspect the inet.0 routing table with show route table inet.0. Which original requirement or fault would most directly justify it?

  1. A technician needs to inspect ordinary unicast IPv4 routes in the default routing instance.
  2. A network should intentionally drop traffic to a configured aggregate when no more specific path exists.
  3. A direct subnet disappears from the routing table after its only supporting interface goes down.
  4. A destination is reachable in routing instance BLUE but not through the default routing table.

Explanation

Correct Answer

A:

The default Junos IPv4 unicast RIB is normally named inet.0. This meets the stated need for default ipv4 routing table.

Incorrect Answers

B:

The static route discard action scenario has a different requirement: A static discard next hop silently drops matching traffic and can provide an aggregation safety route. It does not directly meet the default ipv4 routing table need in this question.

C:

The interface-down connected route scenario has a different requirement: Direct routes depend on their configured interfaces being operational and participating in routing. It does not directly meet the default ipv4 routing table need in this question.

D:

The routing instance ping scenario has a different requirement: Testing from the correct routing instance uses that instance's routing context rather than the default table. It does not directly meet the default ipv4 routing table need in this question.

Question 785

An engineer needs to inspect IPv6 routes without mixing them with ordinary IPv4 prefixes. Which configuration or troubleshooting action most directly meets the need?

  1. Inspect the inet6.0 routing table with show route table inet6.0.
  2. Run show route forwarding-table for the affected destination.
  3. Verify recursive resolution through an active route to the next-hop address.
  4. Use an appropriate dynamic routing protocol instead of relying entirely on manually entered static routes.

Explanation

Correct Answer

A:

Junos normally stores IPv6 unicast routes in inet6.0 rather than the IPv4 inet.0 table. This meets the stated need for default ipv6 routing table.

Incorrect Answers

B:

The inspect installed next hops scenario has a different requirement: The forwarding-table display shows the installed destination and next-hop state used for packet delivery. It does not directly meet the default ipv6 routing table need in this question.

C:

The recursive next-hop resolution scenario has a different requirement: Recursive next-hop resolution finds the outgoing adjacency by looking up the route toward the next hop. It does not directly meet the default ipv6 routing table need in this question.

D:

The static versus dynamic maintenance scenario has a different requirement: Dynamic protocols adapt route advertisements to topology changes and reduce manual route maintenance. It does not directly meet the default ipv6 routing table need in this question.

Question 786

Within Routing Fundamentals, a Junos engineer proposes the following response: Inspect the inet6.0 routing table with show route table inet6.0. Which concept or operating procedure is best illustrated?

  1. Inspect installed next hops
  2. Default IPv6 routing table
  3. Recursive next-hop resolution
  4. Static versus dynamic maintenance

Explanation

Correct Answer

B:

Junos normally stores IPv6 unicast routes in inet6.0 rather than the IPv4 inet.0 table. This meets the stated need for default ipv6 routing table.

Incorrect Answers

A:

The inspect installed next hops scenario has a different requirement: The forwarding-table display shows the installed destination and next-hop state used for packet delivery. It does not directly meet the default ipv6 routing table need in this question.

C:

The recursive next-hop resolution scenario has a different requirement: Recursive next-hop resolution finds the outgoing adjacency by looking up the route toward the next hop. It does not directly meet the default ipv6 routing table need in this question.

D:

The static versus dynamic maintenance scenario has a different requirement: Dynamic protocols adapt route advertisements to topology changes and reduce manual route maintenance. It does not directly meet the default ipv6 routing table need in this question.

Question 787

An engineer needs to inspect IPv6 routes without mixing them with ordinary IPv4 prefixes. The proposed response is: Inspect the inet6.0 routing table with show route table inet6.0. Which explanation most accurately supports this response?

  1. The forwarding-table display shows the installed destination and next-hop state used for packet delivery.
  2. Recursive next-hop resolution finds the outgoing adjacency by looking up the route toward the next hop.
  3. Dynamic protocols adapt route advertisements to topology changes and reduce manual route maintenance.
  4. Junos normally stores IPv6 unicast routes in inet6.0 rather than the IPv4 inet.0 table.

Explanation

Correct Answer

D:

Junos normally stores IPv6 unicast routes in inet6.0 rather than the IPv4 inet.0 table. This meets the stated need for default ipv6 routing table.

Incorrect Answers

A:

The inspect installed next hops scenario has a different requirement: The forwarding-table display shows the installed destination and next-hop state used for packet delivery. It does not directly meet the default ipv6 routing table need in this question.

B:

The recursive next-hop resolution scenario has a different requirement: Recursive next-hop resolution finds the outgoing adjacency by looking up the route toward the next hop. It does not directly meet the default ipv6 routing table need in this question.

C:

The static versus dynamic maintenance scenario has a different requirement: Dynamic protocols adapt route advertisements to topology changes and reduce manual route maintenance. It does not directly meet the default ipv6 routing table need in this question.

Question 788

Within Routing Fundamentals, a technician selects this approach: Inspect the inet6.0 routing table with show route table inet6.0. Which original requirement or fault would most directly justify it?

  1. An engineer needs to inspect IPv6 routes without mixing them with ordinary IPv4 prefixes.
  2. A RIB route is active, yet packets are forwarded unexpectedly and the engineer wants to verify actual entries.
  3. A route has a next-hop IP that is not directly connected, so a second route is needed to reach that next hop.
  4. A remote branch topology changes frequently and manually updating many static routes creates errors.

Explanation

Correct Answer

A:

Junos normally stores IPv6 unicast routes in inet6.0 rather than the IPv4 inet.0 table. This meets the stated need for default ipv6 routing table.

Incorrect Answers

B:

The inspect installed next hops scenario has a different requirement: The forwarding-table display shows the installed destination and next-hop state used for packet delivery. It does not directly meet the default ipv6 routing table need in this question.

C:

The recursive next-hop resolution scenario has a different requirement: Recursive next-hop resolution finds the outgoing adjacency by looking up the route toward the next hop. It does not directly meet the default ipv6 routing table need in this question.

D:

The static versus dynamic maintenance scenario has a different requirement: Dynamic protocols adapt route advertisements to topology changes and reduce manual route maintenance. It does not directly meet the default ipv6 routing table need in this question.

Question 789

The output of show route contains several routes to one prefix and the operator needs the selected route. Which configuration or troubleshooting action most directly meets the need?

  1. Expect the router to drop or reject the unmatched packet according to its forwarding behavior.
  2. Configure an appropriate export policy for the BGP neighbor or group.
  3. Use an appropriate dynamic routing protocol instead of relying entirely on manually entered static routes.
  4. Identify the entry marked with an asterisk as the active selected route.

Explanation

Correct Answer

D:

Junos route displays conventionally mark the active route with an asterisk after the route-entry bracket. This meets the stated need for active route marker.

Incorrect Answers

A:

The no matching ipv4 route scenario has a different requirement: IP forwarding needs a matching installed route; a missing destination and default path cannot yield a valid next hop. It does not directly meet the active route marker need in this question.

B:

The route export to neighbor scenario has a different requirement: A route's presence in the local RIB alone does not guarantee that a routing protocol advertises it. It does not directly meet the active route marker need in this question.

C:

The static versus dynamic maintenance scenario has a different requirement: Dynamic protocols adapt route advertisements to topology changes and reduce manual route maintenance. It does not directly meet the active route marker need in this question.

Question 790

Within Routing Fundamentals, a Junos engineer proposes the following response: Identify the entry marked with an asterisk as the active selected route. Which concept or operating procedure is best illustrated?

  1. No matching IPv4 route
  2. Route export to neighbor
  3. Active route marker
  4. Static versus dynamic maintenance

Explanation

Correct Answer

C:

Junos route displays conventionally mark the active route with an asterisk after the route-entry bracket. This meets the stated need for active route marker.

Incorrect Answers

A:

The no matching ipv4 route scenario has a different requirement: IP forwarding needs a matching installed route; a missing destination and default path cannot yield a valid next hop. It does not directly meet the active route marker need in this question.

B:

The route export to neighbor scenario has a different requirement: A route's presence in the local RIB alone does not guarantee that a routing protocol advertises it. It does not directly meet the active route marker need in this question.

D:

The static versus dynamic maintenance scenario has a different requirement: Dynamic protocols adapt route advertisements to topology changes and reduce manual route maintenance. It does not directly meet the active route marker need in this question.

Junos, Associate (JNCIA-Junos) (JN0-106) Practice Tests