McAfee-Secured Website

Exam Code: NSE7_SSE_AR-26

Exam Name: Fortinet NSE 7 - FortiSASE 26 Architect

Certification Provider: Fortinet

100% Fortinet NSE7_SSE_AR-26 Guaranteed Success With Testking Training Materials

Get Real NSE7_SSE_AR-26 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

50 Questions & Answers with Testing Engine

"Fortinet NSE 7 - FortiSASE 26 Architect Exam", also known as NSE7_SSE_AR-26 exam, is a Fortinet certification exam.

Pass your tests with the always up-to-date NSE7_SSE_AR-26 Exam Engine. Your NSE7_SSE_AR-26 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Fortinet NSE7_SSE_AR-26 Practice Test 23

Question 220

A Fortinet SD-WAN/FortiSASE operations team encounters the following situation: A remote site uses two ISPs but has both IPsec overlay peers pinned to the same primary ISP source address. Which sustained control would best prevent this same failure from recurring?

  1. Audit selectors and prefixes across primary and secondary overlays after application expansion.
  2. Inspect common physical dependencies during overlay redundancy reviews.
  3. Compare BGP neighbor inventory to active overlay tunnels before site handoff.
  4. Test shortcut establishment and fallback through the hub for each ADVPN deployment profile.

Explanation

Correct Answer

B:

This guard addresses the recurring failure mode demonstrated by the case: Logical tunnel duplication does not provide physical resilience when both tunnels share one failed underlay. It guards the same affected workflow, rather than merely checking that some other service works. A successful controlled outcome would be: Disconnecting the primary ISP preserves at least one functional tunnel and learned service routes.

Incorrect Answers

A:

This control is relevant to another scenario in the stated requirement, specifically: A hub failover design assumes every spoke can reach the second hub, but its backup IPsec selectors omit a newly introduced video subnet. It would not prevent the present mechanism: Logical tunnel duplication does not provide physical resilience when both tunnels share one failed underlay. Prevention must be linked to that actual failure mode rather than a generic adjacent control.

C:

This control is relevant to another scenario in the stated requirement, specifically: A hub-and-spoke deployment has two overlay tunnels but only one BGP neighbor defined, so traffic from the backup overlay cannot learn hub service routes. It would not prevent the present mechanism: Logical tunnel duplication does not provide physical resilience when both tunnels share one failed underlay. Prevention must be linked to that actual failure mode rather than a generic adjacent control.

D:

This control is relevant to another scenario in the stated requirement, specifically: A field branch is meant to form temporary direct ADVPN paths to another branch, but only permanent hub-spoke IPsec configuration is in place. It would not prevent the present mechanism: Logical tunnel duplication does not provide physical resilience when both tunnels share one failed underlay. Prevention must be linked to that actual failure mode rather than a generic adjacent control.

Question 221

A Fortinet SD-WAN/FortiSASE operations team encounters the following situation: A hub logs incoming branch ESP traffic but application replies are forwarded through a different unprotected link after a route change. Given this specific Fortinet deployment or fault, which action should the engineer prioritize to resolve the reported condition?

  1. Verify overlay routing adjacencies, advertised prefixes and forwarding routes rather than rebuilding working encryption.
  2. Build resilient loopback reachability across intended overlays before depending on loopback BGP sessions.
  3. Align negotiated IPsec proposals and authentication parameters with the approved hub profile.
  4. Align return routing and protected overlay policy to keep both directions on the intended secure path.

Explanation

Correct Answer

D:

This is the intended corrective decision for the described condition: A hub logs incoming branch ESP traffic but application replies are forwarded through a different unprotected link after a route change. The underlying issue is that The underlay routing change created an asymmetric or bypassed protected return path After this action, the specific acceptance evidence should be: Packet captures on both peers show protected application traffic in each direction after convergence.

Incorrect Answers

A:

This is a plausible action for another Deploy advanced IPsec for SD-WAN situation: An IPsec branch tunnel reports phase 2 up but the application prefix has not been exchanged over BGP, leaving the service unreachable. Its target cause is: Tunnel encryption is established but the route distribution for the destination is incomplete. The present case instead needs to address: The underlay routing change created an asymmetric or bypassed protected return path. It does not directly remediate the actual observed failure.

B:

This is a plausible action for another Deploy advanced IPsec for SD-WAN situation: A large multispoke design uses loopback-based BGP to reduce per-tunnel peering but lacks reliable reachability to peer loopbacks during underlay failure. Its target cause is: Loopback peers depend on transit reachability that was never established on the alternate path. The present case instead needs to address: The underlay routing change created an asymmetric or bypassed protected return path. It does not directly remediate the actual observed failure.

C:

This is a plausible action for another Deploy advanced IPsec for SD-WAN situation: A new spoke cannot negotiate its overlay because its encryption proposals do not overlap those approved on the datacenter peer. Its target cause is: Phase negotiation fails when peers lack a compatible protected-channel configuration. The present case instead needs to address: The underlay routing change created an asymmetric or bypassed protected return path. It does not directly remediate the actual observed failure.

Question 222

A Fortinet SD-WAN/FortiSASE operations team encounters the following situation: A hub logs incoming branch ESP traffic but application replies are forwarded through a different unprotected link after a route change. After the correction is implemented, which observable result most specifically proves this incident was resolved?

  1. Packet captures on both peers show protected application traffic in each direction after convergence.
  2. Peer loopbacks remain reachable and route exchange recovers on the permitted backup overlay.
  3. IKE and IPsec security associations establish using an approved common proposal.
  4. BGP exchanges the required application subnet and test traffic traverses the existing protected tunnel.

Explanation

Correct Answer

A:

This result directly tests whether the observed failure has cleared: A hub logs incoming branch ESP traffic but application replies are forwarded through a different unprotected link after a route change. It confirms the targeted change, Align return routing and protected overlay policy to keep both directions on the intended secure path, rather than a healthy but unrelated component. The technical cause under test is: The underlay routing change created an asymmetric or bypassed protected return path.

Incorrect Answers

B:

That observation verifies a different Deploy advanced IPsec for SD-WAN condition, namely: A large multispoke design uses loopback-based BGP to reduce per-tunnel peering but lacks reliable reachability to peer loopbacks during underlay failure. It could be true even if the current failure persists. In this case the decisive evidence is tied to: The underlay routing change created an asymmetric or bypassed protected return path.

C:

That observation verifies a different Deploy advanced IPsec for SD-WAN condition, namely: A new spoke cannot negotiate its overlay because its encryption proposals do not overlap those approved on the datacenter peer. It could be true even if the current failure persists. In this case the decisive evidence is tied to: The underlay routing change created an asymmetric or bypassed protected return path.

D:

That observation verifies a different Deploy advanced IPsec for SD-WAN condition, namely: An IPsec branch tunnel reports phase 2 up but the application prefix has not been exchanged over BGP, leaving the service unreachable. It could be true even if the current failure persists. In this case the decisive evidence is tied to: The underlay routing change created an asymmetric or bypassed protected return path.

Question 223

A Fortinet SD-WAN/FortiSASE operations team encounters the following situation: A hub logs incoming branch ESP traffic but application replies are forwarded through a different unprotected link after a route change. Which underlying technical cause best explains this precise observed failure?

  1. Phase negotiation fails when peers lack a compatible protected-channel configuration.
  2. The underlay routing change created an asymmetric or bypassed protected return path.
  3. Tunnel encryption is established but the route distribution for the destination is incomplete.
  4. Loopback peers depend on transit reachability that was never established on the alternate path.

Explanation

Correct Answer

B:

This mechanism directly accounts for the observed condition: A hub logs incoming branch ESP traffic but application replies are forwarded through a different unprotected link after a route change. The aligned correction is: Align return routing and protected overlay policy to keep both directions on the intended secure path. A confirming result is: Packet captures on both peers show protected application traffic in each direction after convergence.

Incorrect Answers

A:

This explanation corresponds to an alternative failure context: A new spoke cannot negotiate its overlay because its encryption proposals do not overlap those approved on the datacenter peer. It does not account for the particular evidence in the question. The cause actually associated with the described condition is: The underlay routing change created an asymmetric or bypassed protected return path.

C:

This explanation corresponds to an alternative failure context: An IPsec branch tunnel reports phase 2 up but the application prefix has not been exchanged over BGP, leaving the service unreachable. It does not account for the particular evidence in the question. The cause actually associated with the described condition is: The underlay routing change created an asymmetric or bypassed protected return path.

D:

This explanation corresponds to an alternative failure context: A large multispoke design uses loopback-based BGP to reduce per-tunnel peering but lacks reliable reachability to peer loopbacks during underlay failure. It does not account for the particular evidence in the question. The cause actually associated with the described condition is: The underlay routing change created an asymmetric or bypassed protected return path.

Question 224

A Fortinet SD-WAN/FortiSASE operations team encounters the following situation: A hub logs incoming branch ESP traffic but application replies are forwarded through a different unprotected link after a route change. Which sustained control would best prevent this same failure from recurring?

  1. Test both tunnel state and dynamic route reachability in deployment acceptance.
  2. Document loopback transport dependencies in resilient BGP-on-overlay designs.
  3. Test bidirectional protected flows after hub routing maintenance.
  4. Use centrally validated overlay profiles instead of hand-built inconsistent proposal sets.

Explanation

Correct Answer

C:

This guard addresses the recurring failure mode demonstrated by the case: The underlay routing change created an asymmetric or bypassed protected return path. It guards the same affected workflow, rather than merely checking that some other service works. A successful controlled outcome would be: Packet captures on both peers show protected application traffic in each direction after convergence.

Incorrect Answers

A:

This control is relevant to another scenario in the stated requirement, specifically: An IPsec branch tunnel reports phase 2 up but the application prefix has not been exchanged over BGP, leaving the service unreachable. It would not prevent the present mechanism: The underlay routing change created an asymmetric or bypassed protected return path. Prevention must be linked to that actual failure mode rather than a generic adjacent control.

B:

This control is relevant to another scenario in the stated requirement, specifically: A large multispoke design uses loopback-based BGP to reduce per-tunnel peering but lacks reliable reachability to peer loopbacks during underlay failure. It would not prevent the present mechanism: The underlay routing change created an asymmetric or bypassed protected return path. Prevention must be linked to that actual failure mode rather than a generic adjacent control.

D:

This control is relevant to another scenario in the stated requirement, specifically: A new spoke cannot negotiate its overlay because its encryption proposals do not overlap those approved on the datacenter peer. It would not prevent the present mechanism: The underlay routing change created an asymmetric or bypassed protected return path. Prevention must be linked to that actual failure mode rather than a generic adjacent control.

Question 225

A Fortinet SD-WAN/FortiSASE operations team encounters the following situation: A partner branch uses a different local IKE identity than the datacenter peer expects, despite both peers sharing the correct gateway address. Given this specific Fortinet deployment or fault, which action should the engineer prioritize to resolve the reported condition?

  1. Correct the authenticated peer identity mapping and confirm associated tunnel selectors.
  2. Configure routing adjacency on the intended second overlay and apply appropriate route policy.
  3. Implement the required ADVPN discovery and shortcut design rather than assuming ordinary hub tunnels create dynamic shortcuts.
  4. Build or correct each approved overlay's underlay binding so independent carriers can carry backup tunnels.

Explanation

Correct Answer

A:

This is the intended corrective decision for the described condition: A partner branch uses a different local IKE identity than the datacenter peer expects, despite both peers sharing the correct gateway address. The underlying issue is that Gateway reachability does not compensate for an IKE peer-identity mismatch After this action, the specific acceptance evidence should be: The peers authenticate under the intended identities and the authorized subnet tunnel comes up.

Incorrect Answers

B:

This is a plausible action for another Deploy advanced IPsec for SD-WAN situation: A hub-and-spoke deployment has two overlay tunnels but only one BGP neighbor defined, so traffic from the backup overlay cannot learn hub service routes. Its target cause is: Control-plane route distribution was configured for only one of the data-plane overlays. The present case instead needs to address: Gateway reachability does not compensate for an IKE peer-identity mismatch. It does not directly remediate the actual observed failure.

C:

This is a plausible action for another Deploy advanced IPsec for SD-WAN situation: A field branch is meant to form temporary direct ADVPN paths to another branch, but only permanent hub-spoke IPsec configuration is in place. Its target cause is: The overlay lacks the dynamic discovery behavior needed for spoke-to-spoke optimization. The present case instead needs to address: Gateway reachability does not compensate for an IKE peer-identity mismatch. It does not directly remediate the actual observed failure.

D:

This is a plausible action for another Deploy advanced IPsec for SD-WAN situation: A remote site uses two ISPs but has both IPsec overlay peers pinned to the same primary ISP source address. Its target cause is: Logical tunnel duplication does not provide physical resilience when both tunnels share one failed underlay. The present case instead needs to address: Gateway reachability does not compensate for an IKE peer-identity mismatch. It does not directly remediate the actual observed failure.

Question 226

A Fortinet SD-WAN/FortiSASE operations team encounters the following situation: A partner branch uses a different local IKE identity than the datacenter peer expects, despite both peers sharing the correct gateway address. After the correction is implemented, which observable result most specifically proves this incident was resolved?

  1. A branch-to-branch test establishes an authorized shortcut and avoids unnecessary hub forwarding.
  2. The peers authenticate under the intended identities and the authorized subnet tunnel comes up.
  3. Disconnecting the primary ISP preserves at least one functional tunnel and learned service routes.
  4. Both overlay adjacencies exchange approved routes and failover traffic reaches hub services.

Explanation

Correct Answer

B:

This result directly tests whether the observed failure has cleared: A partner branch uses a different local IKE identity than the datacenter peer expects, despite both peers sharing the correct gateway address. It confirms the targeted change, Correct the authenticated peer identity mapping and confirm associated tunnel selectors, rather than a healthy but unrelated component. The technical cause under test is: Gateway reachability does not compensate for an IKE peer-identity mismatch.

Incorrect Answers

A:

That observation verifies a different Deploy advanced IPsec for SD-WAN condition, namely: A field branch is meant to form temporary direct ADVPN paths to another branch, but only permanent hub-spoke IPsec configuration is in place. It could be true even if the current failure persists. In this case the decisive evidence is tied to: Gateway reachability does not compensate for an IKE peer-identity mismatch.

C:

That observation verifies a different Deploy advanced IPsec for SD-WAN condition, namely: A remote site uses two ISPs but has both IPsec overlay peers pinned to the same primary ISP source address. It could be true even if the current failure persists. In this case the decisive evidence is tied to: Gateway reachability does not compensate for an IKE peer-identity mismatch.

D:

That observation verifies a different Deploy advanced IPsec for SD-WAN condition, namely: A hub-and-spoke deployment has two overlay tunnels but only one BGP neighbor defined, so traffic from the backup overlay cannot learn hub service routes. It could be true even if the current failure persists. In this case the decisive evidence is tied to: Gateway reachability does not compensate for an IKE peer-identity mismatch.

Question 227

A Fortinet SD-WAN/FortiSASE operations team encounters the following situation: A partner branch uses a different local IKE identity than the datacenter peer expects, despite both peers sharing the correct gateway address. Which underlying technical cause best explains this precise observed failure?

  1. Logical tunnel duplication does not provide physical resilience when both tunnels share one failed underlay.
  2. Control-plane route distribution was configured for only one of the data-plane overlays.
  3. Gateway reachability does not compensate for an IKE peer-identity mismatch.
  4. The overlay lacks the dynamic discovery behavior needed for spoke-to-spoke optimization.

Explanation

Correct Answer

C:

This mechanism directly accounts for the observed condition: A partner branch uses a different local IKE identity than the datacenter peer expects, despite both peers sharing the correct gateway address. The aligned correction is: Correct the authenticated peer identity mapping and confirm associated tunnel selectors. A confirming result is: The peers authenticate under the intended identities and the authorized subnet tunnel comes up.

Incorrect Answers

A:

This explanation corresponds to an alternative failure context: A remote site uses two ISPs but has both IPsec overlay peers pinned to the same primary ISP source address. It does not account for the particular evidence in the question. The cause actually associated with the described condition is: Gateway reachability does not compensate for an IKE peer-identity mismatch.

B:

This explanation corresponds to an alternative failure context: A hub-and-spoke deployment has two overlay tunnels but only one BGP neighbor defined, so traffic from the backup overlay cannot learn hub service routes. It does not account for the particular evidence in the question. The cause actually associated with the described condition is: Gateway reachability does not compensate for an IKE peer-identity mismatch.

D:

This explanation corresponds to an alternative failure context: A field branch is meant to form temporary direct ADVPN paths to another branch, but only permanent hub-spoke IPsec configuration is in place. It does not account for the particular evidence in the question. The cause actually associated with the described condition is: Gateway reachability does not compensate for an IKE peer-identity mismatch.

Question 228

A Fortinet SD-WAN/FortiSASE operations team encounters the following situation: A partner branch uses a different local IKE identity than the datacenter peer expects, despite both peers sharing the correct gateway address. Which sustained control would best prevent this same failure from recurring?

  1. Compare BGP neighbor inventory to active overlay tunnels before site handoff.
  2. Test shortcut establishment and fallback through the hub for each ADVPN deployment profile.
  3. Inspect common physical dependencies during overlay redundancy reviews.
  4. Validate peer identities in the deployment manifest before onboarding external sites.

Explanation

Correct Answer

D:

This guard addresses the recurring failure mode demonstrated by the case: Gateway reachability does not compensate for an IKE peer-identity mismatch. It guards the same affected workflow, rather than merely checking that some other service works. A successful controlled outcome would be: The peers authenticate under the intended identities and the authorized subnet tunnel comes up.

Incorrect Answers

A:

This control is relevant to another scenario in the stated requirement, specifically: A hub-and-spoke deployment has two overlay tunnels but only one BGP neighbor defined, so traffic from the backup overlay cannot learn hub service routes. It would not prevent the present mechanism: Gateway reachability does not compensate for an IKE peer-identity mismatch. Prevention must be linked to that actual failure mode rather than a generic adjacent control.

B:

This control is relevant to another scenario in the stated requirement, specifically: A field branch is meant to form temporary direct ADVPN paths to another branch, but only permanent hub-spoke IPsec configuration is in place. It would not prevent the present mechanism: Gateway reachability does not compensate for an IKE peer-identity mismatch. Prevention must be linked to that actual failure mode rather than a generic adjacent control.

C:

This control is relevant to another scenario in the stated requirement, specifically: A remote site uses two ISPs but has both IPsec overlay peers pinned to the same primary ISP source address. It would not prevent the present mechanism: Gateway reachability does not compensate for an IKE peer-identity mismatch. Prevention must be linked to that actual failure mode rather than a generic adjacent control.

Question 229

A Fortinet SD-WAN/FortiSASE operations team encounters the following situation: A regional IPsec tunnel stays reported as established after an ISP black hole because the environment has no effective peer-liveness detection. Given this specific Fortinet deployment or fault, which action should the engineer prioritize to resolve the reported condition?

  1. Build resilient loopback reachability across intended overlays before depending on loopback BGP sessions.
  2. Configure appropriate dead-peer or link-health detection and steering behavior for the redundant overlay.
  3. Align negotiated IPsec proposals and authentication parameters with the approved hub profile.
  4. Align return routing and protected overlay policy to keep both directions on the intended secure path.

Explanation

Correct Answer

B:

This is the intended corrective decision for the described condition: A regional IPsec tunnel stays reported as established after an ISP black hole because the environment has no effective peer-liveness detection. The underlying issue is that Security association state alone can lag a transport failure without liveness monitoring After this action, the specific acceptance evidence should be: A simulated silent ISP failure is detected and protected traffic moves to the healthy tunnel.

Incorrect Answers

A:

This is a plausible action for another Deploy advanced IPsec for SD-WAN situation: A large multispoke design uses loopback-based BGP to reduce per-tunnel peering but lacks reliable reachability to peer loopbacks during underlay failure. Its target cause is: Loopback peers depend on transit reachability that was never established on the alternate path. The present case instead needs to address: Security association state alone can lag a transport failure without liveness monitoring. It does not directly remediate the actual observed failure.

C:

This is a plausible action for another Deploy advanced IPsec for SD-WAN situation: A new spoke cannot negotiate its overlay because its encryption proposals do not overlap those approved on the datacenter peer. Its target cause is: Phase negotiation fails when peers lack a compatible protected-channel configuration. The present case instead needs to address: Security association state alone can lag a transport failure without liveness monitoring. It does not directly remediate the actual observed failure.

D:

This is a plausible action for another Deploy advanced IPsec for SD-WAN situation: A hub logs incoming branch ESP traffic but application replies are forwarded through a different unprotected link after a route change. Its target cause is: The underlay routing change created an asymmetric or bypassed protected return path. The present case instead needs to address: Security association state alone can lag a transport failure without liveness monitoring. It does not directly remediate the actual observed failure.

Question 230

A Fortinet SD-WAN/FortiSASE operations team encounters the following situation: A regional IPsec tunnel stays reported as established after an ISP black hole because the environment has no effective peer-liveness detection. After the correction is implemented, which observable result most specifically proves this incident was resolved?

  1. IKE and IPsec security associations establish using an approved common proposal.
  2. Packet captures on both peers show protected application traffic in each direction after convergence.
  3. A simulated silent ISP failure is detected and protected traffic moves to the healthy tunnel.
  4. Peer loopbacks remain reachable and route exchange recovers on the permitted backup overlay.

Explanation

Correct Answer

C:

This result directly tests whether the observed failure has cleared: A regional IPsec tunnel stays reported as established after an ISP black hole because the environment has no effective peer-liveness detection. It confirms the targeted change, Configure appropriate dead-peer or link-health detection and steering behavior for the redundant overlay, rather than a healthy but unrelated component. The technical cause under test is: Security association state alone can lag a transport failure without liveness monitoring.

Incorrect Answers

A:

That observation verifies a different Deploy advanced IPsec for SD-WAN condition, namely: A new spoke cannot negotiate its overlay because its encryption proposals do not overlap those approved on the datacenter peer. It could be true even if the current failure persists. In this case the decisive evidence is tied to: Security association state alone can lag a transport failure without liveness monitoring.

B:

That observation verifies a different Deploy advanced IPsec for SD-WAN condition, namely: A hub logs incoming branch ESP traffic but application replies are forwarded through a different unprotected link after a route change. It could be true even if the current failure persists. In this case the decisive evidence is tied to: Security association state alone can lag a transport failure without liveness monitoring.

D:

That observation verifies a different Deploy advanced IPsec for SD-WAN condition, namely: A large multispoke design uses loopback-based BGP to reduce per-tunnel peering but lacks reliable reachability to peer loopbacks during underlay failure. It could be true even if the current failure persists. In this case the decisive evidence is tied to: Security association state alone can lag a transport failure without liveness monitoring.

Fortinet NSE 7 - FortiSASE 26 Architect (NSE7_SSE_AR-26) Practice Tests