McAfee-Secured Website

Exam Bundle

Exam Code: N10-009

Exam Name CompTIA Network+

Certification Provider: CompTIA

Corresponding Certification: CompTIA Network+

CompTIA N10-009 Bundle $44.99

100% CompTIA N10-009 Guaranteed Success With Testking Training Materials

Get Real N10-009 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

  • Questions & Answers

    N10-009 Questions & Answers

    768 Questions & Answers

    The ultimate exam preparation tool, Questions & Answers mirrors the actual N10-009 exam while allowing you to hone and measure every aspect of your test-taking ability.

  • N10-009 Video Course

    N10-009 Video Course

    240 Video Lectures

    N10-009 Video Course is developed by CompTIA Professionals to help you pass the N10-009 exam.

    Description

    This course will improve your knowledge and skills required to pass CompTIA Network+ exam.
  • Study Guide

    N10-009 Study Guide

    128 PDF Pages

    Developed by industry experts, this 128-page guide spells out in painstaking detail all of the information you need to ace N10-009 exam.

CompTIA Network+ (N10-009) Practice Tests

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Total Cost: $194.97
Bundle Price: $149.98

Purchase Individually

  • Questions & Answers

    Questions & Answers

    768 Questions

    $124.99
  • N10-009 Video Course

    Video Course

    240 Video Lectures

    $39.99
  • Study Guide

    Study Guide

    128 PDF Pages

    $29.99

CompTIA N10-009 Practice Test 17

Question 160

An outdoor cable develops errors after rain and technicians find corrosion inside a patch panel. Select the most defensible networking decision for this case.

  1. Shorten/restructure the horizontal link or add a compliant active distribution point.
  2. Check PoE class and total power budget versus peak device draw.
  3. Replace moisture-damaged cabling/terminations and protect the entrance from water.
  4. Inspect and repair the event at the measured OTDR distance.

Explanation

Correct Answer

C:

This action addresses the specific requirement because water ingress increases loss and can short or corrode contacts. The independent acceptance check is: Link errors cease in wet conditions and insulation inspection is clean.

Incorrect Answers

A:

This action addresses a different situation: A 110-meter permanent copper run repeatedly fails 1-Gbps certification. It would not directly resolve the current network requirement because water ingress increases loss and can short or corrode contacts.

B:

This action addresses a different situation: A PoE camera reboots only when its heater activates, but the network link tests clean. It would not directly resolve the current network requirement because water ingress increases loss and can short or corrode contacts.

D:

This action addresses a different situation: A fiber OTDR trace shows a large reflection at a newly installed mechanical connector. It would not directly resolve the current network requirement because water ingress increases loss and can short or corrode contacts.

Question 161

Employees use one shared Wi-Fi passphrase, and a departing contractor still knows it. Which recommendation most directly resolves the documented network issue?

  1. Enforce trusted server certificate validation in supplicants and correct RADIUS/EAP provisioning.
  2. Select an autonomous or locally capable AP deployment model with maintainable local security settings.
  3. Select a narrower channel width where survey evidence favors reuse over peak PHY rate.
  4. Replace shared PSK with enterprise 802.1X authentication and individual revocable identities where supported.

Explanation

Correct Answer

D:

This action addresses the specific requirement because enterprise authentication enables per-user authorization and targeted revocation. The independent acceptance check is: The former contractor loses access without rotating every employee's credentials.

Incorrect Answers

A:

This action addresses a different situation: A WPA2-Enterprise SSID uses a RADIUS certificate that clients do not validate. It would not directly resolve the current network requirement because enterprise authentication enables per-user authorization and targeted revocation.

B:

This action addresses a different situation: A standalone remote-office AP must operate without controller connectivity for months. It would not directly resolve the current network requirement because enterprise authentication enables per-user authorization and targeted revocation.

C:

This action addresses a different situation: A crowded 5-GHz office increases channel width to 160 MHz and sees fewer viable nonoverlapping channels. It would not directly resolve the current network requirement because enterprise authentication enables per-user authorization and targeted revocation.

Question 162

A remote network device accepts administrator logins with reused shared accounts and no recorded commands. Which measured outcome provides the strongest evidence of success?

  1. Each permitted change maps to a named administrator, and unapproved commands are rejected.
  2. Altered firmware images are rejected while a verified signed package passes validation.
  3. A scan shows only approved services and factory credentials no longer work.
  4. An unauthorized kiosk is denied or quarantined while a managed device receives its permitted access.

Explanation

Correct Answer

A:

The intended action is: Enforce individualized privileged access and command/session accounting where supported. This works because attribution and audit evidence are essential to change accountability.

Incorrect Answers

B:

This choice would test a different networking condition: A switch firmware package comes from an unverified mirror and IT plans to install it directly. Its related action is: Download from verified sources and check vendor signatures/integrity before a controlled upgrade.

C:

This choice would test a different networking condition: A core switch has factory-default credentials and unused services enabled even though it carries sensitive traffic. Its related action is: Apply a secure device baseline, change default credentials and disable unneeded listeners and ports.

D:

This choice would test a different networking condition: A switch port serving an untrusted kiosk can plug into a sensitive VLAN when an employee swaps the cable. Its related action is: Enforce 802.1X network access control and restrict ports by authenticated identity and posture.

Question 163

A 10-kilometer campus fiber path fails with high loss after multimode short-reach optics were installed. What should the network administrator implement first to meet this requirement?

  1. Match fiber connector polish specifications and protect end faces before connection.
  2. Select compatible single-mode fiber and correctly specified long-reach transceivers for the actual span.
  3. Terminate twisted-pair Ethernet with supported RJ45 modular connectors and tested pair mapping.
  4. Choose matched LC duplex patch leads with the correct polish and fiber type.

Explanation

Correct Answer

B:

This action addresses the specific requirement because optic reach and fiber type must match attenuation and link budget. The independent acceptance check is: Measured receiver optical power and error rate meet the design specification over the full distance.

Incorrect Answers

A:

This action addresses a different situation: Two neighboring switch rooms need an optical handoff and the technician must avoid mixing APC and UPC connectors. It would not directly resolve the current network requirement because optic reach and fiber type must match attenuation and link budget.

C:

This action addresses a different situation: A desk switch has RJ45 jacks but the installer presents RJ11 telephone plugs and intermittent contact. It would not directly resolve the current network requirement because optic reach and fiber type must match attenuation and link budget.

D:

This action addresses a different situation: A fiber patch shelf has duplex LC ports but the replacement patch cable uses incompatible connector geometry. It would not directly resolve the current network requirement because optic reach and fiber type must match attenuation and link budget.

Question 164

An unknown person follows an employee through a locked server-room door while carrying a fake delivery package. Which post-change test best demonstrates that the problem is resolved?

  1. Legitimate service requests stay available during a simulated safe traffic surge while attack classes are filtered.
  2. An uncredentialed test visitor is stopped and escorted through the authorized process.
  3. Forged responses fail validation and authorized clients resolve the legitimate destination.
  4. The test rogue AP triggers a finding and cannot provide uncontrolled internal access.

Explanation

Correct Answer

B:

The intended action is: Apply anti-tailgating procedures with badge challenge and controlled visitor escort. This works because physical social engineering can bypass technical network protections.

Incorrect Answers

A:

This choice would test a different networking condition: A service receives traffic from thousands of machines saturating its internet edge bandwidth. Its related action is: Treat the event as DDoS and engage upstream mitigation/rate controls and capacity plans.

C:

This choice would test a different networking condition: A user visits the correct banking hostname but receives a forged DNS response directing traffic to an impostor server. Its related action is: Investigate DNS spoofing/poisoning and use secure recursive resolution validation where applicable.

D:

This choice would test a different networking condition: An office AP is deployed by a well-meaning employee without authorization and bypasses wireless policy. Its related action is: Detect and remove rogue wireless infrastructure through inventory and WIDS/WIPS monitoring.

Question 165

An incident team has inconclusive packet captures and no permission to change a provider router. Which verification finding would support closing this network issue?

  1. Tests distinguish a site-wide WAN failure from a client-specific DNS issue.
  2. Business traffic passes while prohibited source/destination tests remain denied.
  3. A comparison test isolates the laptop-specific issue without disrupting healthy network users.
  4. Provider staff can reproduce the fault using the supplied path and counters.

Explanation

Correct Answer

D:

The intended action is: Escalate with gathered evidence, clear affected scope and measured timestamps to the authorized owner. This works because unconfirmed theories and absent authority require an evidence-rich escalation, not unauthorized reconfiguration.

Incorrect Answers

A:

This choice would test a different networking condition: Two users report independent failures after a WAN outage, but the NOC assumes both share one cause. Its related action is: Divide the symptoms by path/service and test each probable cause separately.

B:

This choice would test a different networking condition: An engineer fixes lost connectivity by disabling the security ACL but never restores the intended protections. Its related action is: Apply a targeted rule correction and verify both service functionality and security controls.

C:

This choice would test a different networking condition: A technician immediately replaces the core switch after one laptop fails to load a website. Its related action is: Establish and test plausible causes from the smallest impacted scope before replacing shared infrastructure.

Question 166

A core switch loses its running configuration on reboot because only its startup state was backed up months ago. What is the most appropriate network configuration or troubleshooting action for this requirement?

  1. Schedule authenticated configuration backups and test restore integrity after significant changes.
  2. Update logical route maps and physical diagrams under the same change record.
  3. Maintain versioned, protected off-device golden baselines and compare production against them.
  4. Route configuration changes through controlled approvals, versioned baselines and audit records.

Explanation

Correct Answer

A:

This action addresses the specific requirement because configuration management must capture the actual current operational state. The independent acceptance check is: A lab restore reproduces the intended VLAN and routing configuration from the latest protected backup.

Incorrect Answers

B:

This action addresses a different situation: An upgrade changes the routing design but engineers keep only a screenshot of the old physical switch layout. It would not directly resolve the current network requirement because configuration management must capture the actual current operational state.

C:

This action addresses a different situation: A team stores golden configurations only on the live devices they are intended to rebuild. It would not directly resolve the current network requirement because configuration management must capture the actual current operational state.

D:

This action addresses a different situation: An engineer changes switch spanning-tree priorities through a personal script without a ticket or peer review. It would not directly resolve the current network requirement because configuration management must capture the actual current operational state.

Question 167

A mesh WLAN has too many repeaters in series and throughput falls at the far end. Which verification finding would support closing this network issue?

  1. The AP appears joined to the intended controller and advertises authorized SSIDs.
  2. Capable clients increasingly choose 5 GHz without stranding legacy clients.
  3. Measured far-end throughput improves after optimizing hop count and backhaul capacity.
  4. AP logs show compliant channel moves and clients recover through the supported transition process.

Explanation

Correct Answer

C:

The intended action is: Reduce unnecessary wireless backhaul hops or use wired uplinks where possible. This works because shared-radio multi-hop backhaul can consume airtime on each relay.

Incorrect Answers

A:

This choice would test a different networking condition: A newly installed lightweight AP cannot serve users because it has not joined its controller. Its related action is: Verify controller discovery, management reachability and authorized AP adoption.

B:

This choice would test a different networking condition: A Wi-Fi analyst forces all laptops to 2.4 GHz despite good 5-GHz conditions, worsening congestion. Its related action is: Enable suitable band steering while ensuring clients retain compatible connectivity.

D:

This choice would test a different networking condition: A DFS-sensitive 5-GHz WLAN drops briefly when radar detection forces a channel change. Its related action is: Plan for dynamic frequency selection and regulatory channel constraints, including 802.11h behavior.

Question 168

A campus has separate access, distribution and core tiers and needs scalable routed aggregation. After the change, which result is most relevant to the original failure?

  1. Server-to-server throughput remains stable across alternate spines during a controlled link failure.
  2. Endpoints achieve measured bidirectional throughput and fade margin at the intended distance.
  3. The defined node-to-node routes survive an individual interconnect failure.
  4. An access-switch failure stays localized while core transit continues across other buildings.

Explanation

Correct Answer

D:

The intended action is: Preserve distinct access, distribution and core functions with appropriate routing boundaries. This works because three-tier hierarchy separates endpoint attachment, policy aggregation and backbone transport.

Incorrect Answers

A:

This choice would test a different networking condition: A data center runs many east-west server transactions and wants predictable leaf-to-leaf paths at scale. Its related action is: Use a spine-leaf fabric design with bounded hops and appropriate equal-cost paths.

B:

This choice would test a different networking condition: A bridge between two remote towers uses a dedicated wireless path with only two endpoints. Its related action is: Implement a point-to-point wireless link with matching line-of-sight and antenna requirements.

C:

This choice would test a different networking condition: A research cluster has direct links between all critical nodes to eliminate a single central switch dependency. Its related action is: Evaluate a full or partial mesh topology based on required alternate paths and port cost.

Question 169

All clients in one subnet can reach the IP of a website but cannot resolve its FQDN. After the change, which result is most relevant to the original failure?

  1. The hostname returns the intended address and browser access works.
  2. A name query returns the expected host without dangling aliases.
  3. The laptop learns the intended default router and reaches permitted off-subnet IPv6 targets without admitting rogue advertisements.
  4. The signed zone validates successfully while intentionally forged answers remain rejected.

Explanation

Correct Answer

A:

The intended action is: Check resolver addresses, DNS queries and zone records rather than default-route forwarding alone. This works because iP connectivity with name failure points toward DNS service/configuration.

Incorrect Answers

B:

This choice would test a different networking condition: An enterprise portal fails only when accessed by name after its DNS CNAME target was deleted. Its related action is: Repair the alias target chain and verify the final A/AAAA resolution.

C:

This choice would test a different networking condition: An IPv6 laptop loses its default gateway after a switch ACL begins filtering router advertisements and neighbor discovery. Its related action is: Allow legitimate ICMPv6 router advertisements and neighbor discovery on the local segment while blocking rogue sources.

D:

This choice would test a different networking condition: A link's DNSSEC-enabled resolver rejects one domain after a mismatched DS/DNSKEY rollover. Its related action is: Validate the chain of trust and repair signed-zone key/DS alignment.

Question 170

A campus needs its access VLANs routed through SVIs on a multilayer switch. Select the most defensible networking decision for this case.

  1. Prune the allowed VLAN list to documented required VLANs and verify legitimate services.
  2. Ensure VLAN 200 has an active eligible access or trunk port before expecting the SVI line protocol to rise.
  3. Create SVIs with the VLAN interfaces present and enable supported Layer 3 routing.
  4. Mark and queue trusted voice traffic using a consistent switch QoS policy.

Explanation

Correct Answer

C:

This action addresses the specific requirement because an SVI provides an IP gateway for a VLAN on an L3-capable switch. The independent acceptance check is: Each VLAN client reaches its SVI and permitted inter-VLAN traffic follows ACLs.

Incorrect Answers

A:

This action addresses a different situation: A switch's trunk permits every VLAN including old decommissioned segments. It would not directly resolve the current network requirement because an SVI provides an IP gateway for a VLAN on an L3-capable switch.

B:

This action addresses a different situation: An SVI configured for VLAN 200 remains down even after an administrator enables the interface, and no operational switchport carries that VLAN. It would not directly resolve the current network requirement because an SVI provides an IP gateway for a VLAN on an L3-capable switch.

D:

This action addresses a different situation: A voice phone needs priority during a saturated trunk but VLAN tagging alone does not guarantee QoS. It would not directly resolve the current network requirement because an SVI provides an IP gateway for a VLAN on an L3-capable switch.