McAfee-Secured Website

Exam Bundle

Exam Code: 200-301

Exam Name Cisco Certified Network Associate (CCNA)

Certification Provider: Cisco

Corresponding Certification: CCNA

Cisco 200-301 Bundle $44.99

100% Cisco 200-301 Guaranteed Success With Testking Training Materials

Get Real 200-301 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

  • Questions & Answers

    200-301 Questions & Answers

    760 Questions & Answers

    The ultimate exam preparation tool, Questions & Answers mirrors the actual 200-301 exam while allowing you to hone and measure every aspect of your test-taking ability.

  • 200-301 Video Course

    200-301 Video Course

    271 Video Lectures

    200-301 Video Course is developed by Cisco Professionals to help you pass the 200-301 exam.

    Description

    This course will improve your knowledge and skills required to pass Cisco Certified Network Associate (CCNA) exam.
  • Study Guide

    200-301 Study Guide

    1969 PDF Pages

    Developed by industry experts, this 1969-page guide spells out in painstaking detail all of the information you need to ace 200-301 exam.

Cisco Certified Network Associate (CCNA) (200-301) Practice Tests

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Total Cost: $194.97
Bundle Price: $149.98

Purchase Individually

  • Questions & Answers

    Questions & Answers

    760 Questions

    $124.99
  • 200-301 Video Course

    Video Course

    271 Video Lectures

    $39.99
  • Study Guide

    Study Guide

    1969 PDF Pages

    $29.99

Cisco 200-301 Practice Test 66

Question 650

A preferred gateway should reclaim HSRP forwarding after its priority returns above that of the current active member. What configurable behavior is required?

  1. HSRP as a Cisco first-hop redundancy protocol
  2. An eligible standby FHRP router can take over if the active member fails
  3. Point each host at the FHRP virtual IP, not one router physical interface IP
  4. Preemption when the preferred higher-priority gateway should retake active role

Explanation

Correct Answer

D:

HSRP preemption controls whether a higher-priority eligible router retakes active role.

Incorrect Answers

A:

Cisco HSRP supports active/standby virtual default gateway functions; for the higher-priority gateway reclaiming HSRP activity after recovery, the relevant operation is restoring a preferred router to active status automatically, not choosing Cisco-developed HSRP specifically.

B:

FHRP backup members monitor active service and can assume forwarding on loss; for the higher-priority gateway reclaiming HSRP activity after recovery, the relevant operation is restoring a preferred router to active status automatically, not failover to a surviving standby after active failure.

C:

Using a virtual gateway lets hosts keep one default-gateway address during active-router failure; for the higher-priority gateway reclaiming HSRP activity after recovery, the relevant operation is restoring a preferred router to active status automatically, not making each client actually rely on the failover-capable gateway.

Question 651

At a warehouse distribution floor, internal web host 10.7.20.12 must always be translated to public address 198.51.100.9. Which IOS static inside-source NAT statement establishes the requested one-to-one mapping?

  1. ip nat inside source static 10.7.20.12 198.51.100.9
  2. ip nat outside source static 10.7.20.12 198.51.100.9
  3. ip nat inside source static 10.7.20.12 0.0.0.0
  4. ip nat inside source static 198.51.100.9 10.7.20.12

Explanation

Correct Answer

A:

Static inside-source NAT maps one fixed inside-local host address to an inside-global public address in the specified direction.

Incorrect Answers

B:

Outside-source translation concerns another address direction and does not meet the inside-source mapping.

C:

0.0.0.0 is not the intended fixed public inside-global address.

D:

The address order is reversed: inside local must be followed by inside global.

Question 652

A branch router at an enterprise data center has a private LAN and an upstream ISP. Its inside-source NAT rules exist but translations do not occur because both interfaces have the wrong NAT designation. What roles should be configured?

  1. Configure ip nat inside on both interfaces
  2. Configure only a default route and no NAT inside/outside roles
  3. Mark the user-facing interface as ip nat inside and the provider-facing interface as ip nat outside
  4. Configure ip nat outside on both interfaces

Explanation

Correct Answer

C:

Cisco IOS inside-source NAT requires the correct inside and outside interface roles for the translation path.

Incorrect Answers

A:

Two inside interfaces lack a designated outside interface.

B:

Routing alone does not establish NAT interface roles or translation rules.

D:

Two outside interfaces lack an inside direction for standard inside-source translation.

Question 653

A router must define dynamic NAT public pool PUBPOOL covering 198.51.100.33 through 198.51.100.37 on a /24 provider block. Which command defines the pool address range?

  1. ip nat inside source static 10.29.20.12 198.51.100.33
  2. ip route 198.51.100.33 255.255.255.0 10.29.20.12
  3. ip nat pool PUBPOOL 198.51.100.33 198.51.100.37 netmask 255.255.0.0
  4. ip nat pool PUBPOOL 198.51.100.33 198.51.100.37 netmask 255.255.255.0

Explanation

Correct Answer

D:

An IOS NAT pool specifies first/last inside-global addresses and the subnet mask used for the pool.

Incorrect Answers

A:

Static mapping binds one private host to one global address and does not define a shared pool.

B:

An IP route is a forwarding entry, not a NAT address pool definition.

C:

The configured pool netmask differs from the specified /24 address pool requirement.

Question 654

At a regional healthcare office, the NAT pool is already defined, but private hosts are not translated because no mapping selects which inside clients use it. What configuration link is required?

  1. Use an ACL matching the inside subnet plus an ip nat inside source list ... pool ... rule
  2. Apply only the public NAT pool with no source selection rule
  3. Configure ip nat outside on both interfaces
  4. Use a destination-only ACL in place of the inside-source selection list

Explanation

Correct Answer

A:

Dynamic inside-source NAT connects selected inside local addresses to the public translation pool using an ACL and pool rule.

Incorrect Answers

B:

A defined pool alone does not specify which inside sources should translate.

C:

Incorrect NAT interface directions prevent intended inside-source translations.

D:

Inside-source NAT selects inside source addresses rather than an arbitrary destination-only condition.

Question 655

At a municipal library, 160 private client hosts must browse the Internet through one assigned public IPv4 address. Which NAT mode supports concurrent outbound connections efficiently?

  1. Use PAT overload so multiple inside clients share the available global address with distinct port mappings
  2. Disable translation and advertise the private host addresses to the Internet
  3. Use a separate static one-to-one NAT mapping for every potential ephemeral flow
  4. Map all clients to the same public IP without tracking ports or sessions

Explanation

Correct Answer

A:

NAT overload (PAT) multiplexes many private flows through one or a few global addresses by tracking ports/session identifiers.

Incorrect Answers

B:

RFC 1918 addresses cannot be used as public globally routed clients without appropriate translation or design.

C:

Static 1:1 mappings waste addresses and do not address the stated shared-address requirement.

D:

Without distinct transport mappings the return path cannot reliably distinguish concurrent private sessions.

Question 656

An operator must confirm that packets from 10.62.20.12 are being translated to assigned public addresses on an IOS edge router. Which command reveals live NAT mappings?

  1. show ip nat translations
  2. show cdp neighbors
  3. show interfaces trunk
  4. show spanning-tree

Explanation

Correct Answer

A:

show ip nat translations displays current inside-local/inside-global translation mappings, including port translations where applicable.

Incorrect Answers

B:

CDP neighbor information does not list IP NAT translation state.

C:

802.1Q trunk status does not show NAT inside/global mappings.

D:

STP state is unrelated to NAT mappings.

Question 657

A private printer 10.12.4.20 must always appear externally as 203.0.113.20. Which IOS statement creates this fixed inside-source mapping?

  1. `ip nat inside source static 10.12.4.20 203.0.113.20`
  2. `ip nat outside source static 203.0.113.20 10.12.4.20`
  3. `ip nat inside source static 10.12.4.20 203.0.113.20 overload`
  4. `ip nat inside source static 203.0.113.20 10.12.4.20`

Explanation

Correct Answer

A:

Static inside-source NAT maps the configured inside-local host address to its fixed inside-global address.

Incorrect Answers

B:

Outside-source NAT translates a different address role, not this inside host.

C:

Overload is a PAT concept and not needed for this one-to-one static address mapping.

D:

The reversed addresses put the global address in the inside-local field.

Question 658

`show ip nat translations` lists Inside local 192.168.5.10 and Inside global 198.51.100.10 for an outbound connection. What is the inside-global value?

  1. The inside interface MAC address
  2. 192.168.5.10
  3. The remote Internet server address
  4. 198.51.100.10

Explanation

Correct Answer

D:

Inside global is the externally visible translated address representing the local inside host.

Incorrect Answers

A:

The NAT table maps IP addresses and possibly ports, not a translated inside interface MAC.

B:

192.168.5.10 is the inside-local private address before translation.

C:

The remote server is an outside host, not this inside-global translation.

Question 659

A router connects Gi0/0 to 10.9.0.0/24 clients and Gi0/1 to the public ISP circuit. Which NAT role configuration is appropriate?

  1. `ip nat inside` on both physical interfaces.
  2. `ip nat outside` on Gi0/0 and `ip nat inside` on Gi0/1.
  3. `ip nat outside` on both physical interfaces.
  4. `ip nat inside` on Gi0/0 and `ip nat outside` on Gi0/1.

Explanation

Correct Answer

D:

For inside-source NAT, the private client side is inside while the external ISP-facing side is outside.

Incorrect Answers

A:

Both marked inside leave no outside NAT boundary.

B:

Reversing the roles misidentifies the private and public sides.

C:

Both interfaces marked outside leave no correct internal source role.

Question 660

Dynamic inside-source NAT uses ACL 10 with `permit 10.10.10.0 0.0.0.255`. Clients in 10.10.20.0/24 receive no translation. All interfaces and pool configuration are correct. What should be changed?

  1. Assign the remote Web server a different MAC address.
  2. Make the client access VLAN the trunk native VLAN.
  3. Change OSPF DR priority to zero on the NAT router.
  4. Include 10.10.20.0/24 in the NAT source-match ACL.

Explanation

Correct Answer

D:

An inside-source dynamic NAT rule only translates inside addresses that match its configured standard ACL.

Incorrect Answers

A:

Server MAC changes do not make the 10.10.20.0/24 client source match ACL 10.

B:

Native VLAN assignment does not edit NAT source eligibility.

C:

OSPF DR priority is unrelated to the NAT source-list match.