McAfee-Secured Website

Exam Bundle

Exam Code: 200-301

Exam Name Cisco Certified Network Associate (CCNA)

Certification Provider: Cisco

Corresponding Certification: CCNA

Cisco 200-301 Bundle $44.99

100% Cisco 200-301 Guaranteed Success With Testking Training Materials

Get Real 200-301 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

  • Questions & Answers

    200-301 Questions & Answers

    760 Questions & Answers

    The ultimate exam preparation tool, Questions & Answers mirrors the actual 200-301 exam while allowing you to hone and measure every aspect of your test-taking ability.

  • 200-301 Video Course

    200-301 Video Course

    271 Video Lectures

    200-301 Video Course is developed by Cisco Professionals to help you pass the 200-301 exam.

    Description

    This course will improve your knowledge and skills required to pass Cisco Certified Network Associate (CCNA) exam.
  • Study Guide

    200-301 Study Guide

    1969 PDF Pages

    Developed by industry experts, this 1969-page guide spells out in painstaking detail all of the information you need to ace 200-301 exam.

Cisco Certified Network Associate (CCNA) (200-301) Practice Tests

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Total Cost: $194.97
Bundle Price: $149.98

Purchase Individually

  • Questions & Answers

    Questions & Answers

    760 Questions

    $124.99
  • 200-301 Video Course

    Video Course

    271 Video Lectures

    $39.99
  • Study Guide

    Study Guide

    1969 PDF Pages

    $29.99

Cisco 200-301 Practice Test 25

Question 240

A switch’s access port Gi0/15 is in VLAN 80 and a host has address 10.80.4.44/24. The gateway SVI for VLAN 80 was configured 10.80.4.255/24. What must the administrator change?

  1. Set the host IP to the directed broadcast 10.80.4.255
  2. Set VLAN 80 to the switch’s native VLAN
  3. Configure an OSPF router ID matching 10.80.4.255
  4. Select a usable unicast gateway address such as 10.80.4.1/24 for Vlan80

Explanation

Correct Answer

D:

The .255 address is the directed broadcast of the /24 and cannot serve as an ordinary gateway interface address.

Incorrect Answers

A:

A broadcast destination cannot be assigned as a conventional unicast host identity.

B:

Native tagging is unrelated to the invalid IPv4 SVI address.

C:

An OSPF router ID does not make a broadcast address usable for an SVI.

Question 241

A PC should join VLAN 34, but `show interfaces Gi1/0/7 switchport` reports Access Mode VLAN 43 and Administrative Mode static access. Which change resolves the membership mismatch?

  1. Enable a higher STP priority on VLAN 43
  2. Set the switch port to routed mode
  3. Configure `switchport access vlan 34` on Gi1/0/7
  4. Change the PC DNS resolver only

Explanation

Correct Answer

C:

The operational access VLAN is 43, so the port must be explicitly assigned to the intended 34 before ordinary untagged client frames enter it.

Incorrect Answers

A:

Root-election priority does not make the host join the requested VLAN.

B:

The end-host connection needs an access VLAN, not a Layer 3 switchport.

D:

DNS does not alter the VLAN where the switch classifies untagged Ethernet frames.

Question 242

A Cisco IP phone and attached workstation share one switch port. The phone needs voice VLAN 190, while the PC must remain in data VLAN 30. Which pair of interface settings meets the requirement?

  1. switchport mode trunk with every VLAN allowed to the PC
  2. Assign both devices the same IP address to share their port
  3. switchport access vlan 30 and switchport voice vlan 190
  4. switchport access vlan 190 and remove the data VLAN

Explanation

Correct Answer

C:

Cisco access ports can specify a separate voice VLAN while untagged PC data remains in the data VLAN.

Incorrect Answers

A:

The workstation behind the phone does not require an unrestricted trunk.

B:

Sharing a physical switch port does not permit identical endpoint IP addresses.

D:

That would place the workstation in the voice VLAN rather than its required data VLAN.

Question 243

A router subinterface Gi0/0.50 should provide the default gateway for VLAN 50 on an 802.1Q trunk. Which configuration element identifies the incoming VLAN tag?

  1. `switchport access vlan 50` on the router subinterface
  2. `ip address 50.50.50.50 255.0.0.0` alone
  3. `router ospf 50` on the router subinterface
  4. `encapsulation dot1Q 50`

Explanation

Correct Answer

D:

Router-on-a-stick subinterfaces classify tagged frames using the 802.1Q VLAN ID, then provide an IP gateway for that VLAN.

Incorrect Answers

A:

Router routed subinterfaces do not use switch access port VLAN commands.

B:

An interface IP alone does not identify the VLAN tag sent by the switch trunk.

C:

OSPF process selection does not bind an 802.1Q tag to a subinterface.

Question 244

A router-on-a-stick link has working gateways for VLANs 10 and 20. The switch adds VLAN 30 but leaves the 802.1Q trunk allowed list at `10,20`. The router has Gi0/0.30 with the right IP and dot1Q tag. Why does VLAN 30 still fail?

  1. The router must use `switchport access vlan 30` on Gi0/0.30
  2. Hosts in VLAN 30 must be assigned to untagged VLAN 10
  3. The destination route requires administrative distance 200
  4. VLAN 30 frames are blocked by the switch trunk’s allowed-VLAN list

Explanation

Correct Answer

D:

The router subinterface may be correct, but the switch uplink must actually carry tagged VLAN 30 traffic.

Incorrect Answers

A:

Router subinterfaces use encapsulation dot1Q, not switchport access commands.

B:

Moving hosts to a different VLAN defeats the requirement for a third routed segment.

C:

Administrative distance does not govern local 802.1Q trunk VLAN permission.

Question 245

A VoIP phone is connected to Fa0/10, and an administrator must confirm both data and auxiliary voice VLAN assignments on that switchport. Which IOS command shows the administrative access and voice VLAN state?

  1. `show ip ospf neighbor`
  2. `show ip nat translations`
  3. `show interfaces fa0/10 switchport`
  4. `show vlan brief` alone to identify the phone MAC

Explanation

Correct Answer

C:

The detailed switchport output reports access mode/VLAN and voice VLAN configuration for that interface.

Incorrect Answers

A:

OSPF neighbor output concerns routing adjacencies, not switchport voice VLAN configuration.

B:

NAT translations have no relationship to local phone VLAN assignment.

D:

The generic VLAN table alone does not reliably identify both roles on the exact switchport.

Question 246

Two switches at a warehouse distribution floor must carry VLAN 10 and VLAN 140 across Gi1/0/1. Both switches support IEEE 802.1Q. Which interface mode should be configured?

  1. switchport access vlan 10 on Gi1/0/1 only
  2. switchport mode trunk on Gi1/0/1
  3. no switchport on Gi1/0/1
  4. switchport mode access on Gi1/0/1

Explanation

Correct Answer

B:

A Layer 2 trunk transports frames for multiple VLANs between switches using tagged VLAN identifiers.

Incorrect Answers

A:

An access VLAN command by itself does not put the link into trunk mode.

C:

Routed port mode removes ordinary Layer 2 VLAN trunking.

D:

Access mode normally carries one data VLAN rather than the requested multi-VLAN trunk.

Question 247

A switch-to-switch trunk at an enterprise data center reports a native VLAN mismatch: one end is VLAN 23, while the other is VLAN 143. The design specifies native VLAN 23. Which correction meets the design?

  1. switchport access vlan 23 on only one end
  2. switchport trunk allowed vlan 23 but keep native VLANs mismatched
  3. switchport trunk native vlan 23 on both ends
  4. no switchport on one end

Explanation

Correct Answer

C:

The native VLAN must agree across both ends of a dot1q trunk so untagged frames map consistently.

Incorrect Answers

A:

Changing an access VLAN does not reconcile trunk native-VLAN mapping.

B:

An allowed-VLAN entry does not resolve a mismatched untagged/native VLAN ID.

D:

Routed port mode is not the intended Layer 2 trunk configuration.

Question 248

At a disaster-recovery location, VLAN 36 exists on both switches and the trunk is up, but show interfaces trunk lists only VLAN 146 as allowed. What change allows VLAN 36 traffic across the link?

  1. switchport trunk native vlan 36 on one end without modifying allowed VLANs
  2. switchport trunk allowed vlan add 36 on the missing trunk
  3. switchport trunk allowed vlan remove 36
  4. switchport access vlan 36 on an unrelated host port

Explanation

Correct Answer

B:

A VLAN omitted from the allowed list cannot traverse that trunk even if its VLAN exists locally.

Incorrect Answers

A:

Changing the native VLAN does not automatically add a missing VLAN to the permitted list.

C:

Removing the VLAN makes the permitted trunk set even less suitable.

D:

Changing a host access port does not update the restricted trunk allowed list.

Question 249

A packet capture on a trunk at a regional healthcare office shows an untagged Ethernet data frame and tagged frames for VLANs 49 and 149. How does the receiving switch classify the untagged frame?

  1. Every 802.1Q VLAN is always carried untagged on the same wire
  2. A VLAN number is encoded inside the IP header for every tagged frame
  3. Untagged ingress frames are associated with the configured native VLAN
  4. Only router-on-a-stick interfaces are permitted to send tagged Ethernet frames

Explanation

Correct Answer

C:

On an ordinary 802.1Q trunk, the native VLAN is the default mapping for untagged frames; other VLANs are normally tagged.

Incorrect Answers

A:

Normal dot1q operation distinguishes VLANs using 802.1Q tags, apart from the native VLAN case.

B:

The dot1q VLAN identifier belongs to the Ethernet tag, not to an IP header field.

D:

Switch-to-switch trunks also use dot1q tagging without router subinterfaces.

Question 250

A multi-switch path at a municipal library passes VLAN 152 but drops VLAN 62, even though both end hosts have valid IPs. Which layer-two checks best isolate this failure?

  1. Assume that a VLAN exists on one switch so it must automatically pass every intermediate trunk
  2. Verify trunk operational status, permitted VLAN list and native VLAN consistency at both ends
  3. Ignore operational trunk mode and inspect only host DNS settings
  4. Disable both trunk interfaces permanently

Explanation

Correct Answer

B:

A multi-switch VLAN path depends on each trunk actually forming and carrying the relevant VLANs with consistent tagging.

Incorrect Answers

A:

VLAN existence is local and does not guarantee that every trunk forwards that VLAN.

C:

DNS is above Layer 2 and does not verify trunk formation or allowed VLAN lists.

D:

Turning down the trunks removes all connectivity rather than diagnosing one VLAN failure.