McAfee-Secured Website

Exam Bundle

Exam Code: N10-009

Exam Name CompTIA Network+

Certification Provider: CompTIA

Corresponding Certification: CompTIA Network+

CompTIA N10-009 Bundle $44.99

100% CompTIA N10-009 Guaranteed Success With Testking Training Materials

Get Real N10-009 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

  • Questions & Answers

    N10-009 Questions & Answers

    768 Questions & Answers

    The ultimate exam preparation tool, Questions & Answers mirrors the actual N10-009 exam while allowing you to hone and measure every aspect of your test-taking ability.

  • N10-009 Video Course

    N10-009 Video Course

    240 Video Lectures

    N10-009 Video Course is developed by CompTIA Professionals to help you pass the N10-009 exam.

    Description

    This course will improve your knowledge and skills required to pass CompTIA Network+ exam.
  • Study Guide

    N10-009 Study Guide

    128 PDF Pages

    Developed by industry experts, this 128-page guide spells out in painstaking detail all of the information you need to ace N10-009 exam.

CompTIA Network+ (N10-009) Practice Tests

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Total Cost: $194.97
Bundle Price: $149.98

Purchase Individually

  • Questions & Answers

    Questions & Answers

    768 Questions

    $124.99
  • N10-009 Video Course

    Video Course

    240 Video Lectures

    $39.99
  • Study Guide

    Study Guide

    128 PDF Pages

    $29.99

CompTIA N10-009 Practice Test 44

Question 430

A VPN tunnel is up but clients cannot use applications because permitted routes were never pushed to remote devices. Select the most defensible networking decision for this case.

  1. Verify client route distribution, split/full tunnel rules and internal DNS settings.
  2. Correct MX preferences and destinations, including the referenced mail host records.
  3. Inspect the HTTPS listener and intervening TCP 443 ACL/firewall policy.
  4. Inspect relevant route-table entries and next hops, restoring the authorized destination route.

Explanation

Correct Answer

A:

This action addresses the specific requirement because authentication and tunnel establishment do not guarantee application reachability. The independent acceptance check is: A connected client receives the intended routes and resolves internal names.

Incorrect Answers

B:

This action addresses a different situation: A site can ping its mail exchanger but inbound email fails after a change to MX records. It would not directly resolve the current network requirement because authentication and tunnel establishment do not guarantee application reachability.

C:

This action addresses a different situation: A web application resolves the correct hostname but only TCP 443 fails while ICMP ping works. It would not directly resolve the current network requirement because authentication and tunnel establishment do not guarantee application reachability.

D:

This action addresses a different situation: Clients reach two local VLANs but the route to an external site disappears after a routing-policy change. It would not directly resolve the current network requirement because authentication and tunnel establishment do not guarantee application reachability.

Question 431

A 2.5-Gbps access point uplink falls back to 100 Mbps over an old two-pair cable. Which solution best satisfies the technical constraint without introducing unrelated changes?

  1. Replace the crushed segment and protect the replacement cable path.
  2. Install a certified four-pair cable and verify endpoint/switch multigig capability.
  3. Install matched, vendor-supported optics for the same wavelength and fiber type.
  4. Check PoE class and total power budget versus peak device draw.

Explanation

Correct Answer

B:

This action addresses the specific requirement because higher Ethernet rates require supported wiring and PHY at both ends. The independent acceptance check is: The AP port negotiates the intended multigig speed without errors.

Incorrect Answers

A:

This action addresses a different situation: A copper pair appears shorted in a cable tester after a technician crushed the cable under a raised floor. It would not directly resolve the current network requirement because higher Ethernet rates require supported wiring and PHY at both ends.

C:

This action addresses a different situation: A switch's 10-Gbps port has the correct fiber but incompatible SR optics on one side and LR optics on the other. It would not directly resolve the current network requirement because higher Ethernet rates require supported wiring and PHY at both ends.

D:

This action addresses a different situation: A PoE camera reboots only when its heater activates, but the network link tests clean. It would not directly resolve the current network requirement because higher Ethernet rates require supported wiring and PHY at both ends.

Question 432

A branch's outage coincides with a firewall policy change and the engineer has three competing theories. Which verification finding would support closing this network issue?

  1. Full transaction tests succeed across every required service and prevention notes are recorded.
  2. The suspect port is isolated without disconnecting unrelated users.
  3. The incident record identifies reproducible impact conditions and a clearly defined affected population.
  4. A controlled rollback or rule test confirms or rejects the suspected policy cause.

Explanation

Correct Answer

D:

The intended action is: Test the most likely, minimally disruptive theory with evidence and a rollback plan. This works because a time-correlated change is a hypothesis, not proof of causation.

Incorrect Answers

A:

This choice would test a different networking condition: A firewall rule change restores traffic but the technician only tests the initiating host, not the dependent application workflow. Its related action is: Verify end-to-end application function and downstream dependencies before closure.

B:

This choice would test a different networking condition: A proposed fix requires resetting every switch in the building to test whether one access port is faulty. Its related action is: Use a low-impact targeted test or escalate before taking disruptive action.

C:

This choice would test a different networking condition: A help desk ticket says 'network slow' without location, time, affected services or recent changes. Its related action is: Begin with symptom collection, affected scope, user questions and recent-change inventory.

Question 433

A network switch has no usable IP configuration after a factory reset, so remote SSH cannot yet work. Which post-change test best demonstrates that the problem is resolved?

  1. An approved user connects to permitted subnets while a denied device fails policy checks.
  2. Operators reach a failed-router console while its production interfaces are disconnected.
  3. The switch receives a reachable management address, and authorized SSH works after setup.
  4. Approved hosts at both sites communicate after tunnel failover with no per-user VPN action.

Explanation

Correct Answer

C:

The intended action is: Use an authenticated local console connection to establish bootstrap management and then enable secure remote access. This works because initial console access can configure networking before in-band management becomes available.

Incorrect Answers

A:

This choice would test a different networking condition: Remote staff need a VPN client that exposes authorized internal subnets only after user and device verification. Its related action is: Use authenticated client-to-site VPN with suitable MFA and endpoint policy.

B:

This choice would test a different networking condition: An engineer must access routers during a core IP outage, but the only management path uses the failed production network. Its related action is: Provide out-of-band management via independent console server or cellular path with strong access controls.

D:

This choice would test a different networking condition: Two branch sites need permanent routed connectivity for application replication without end-user clients initiating VPN sessions. Its related action is: Establish a site-to-site VPN with matching crypto/authentication policies and routed networks.

Question 434

An access switch uplink must carry both VLAN 100 and VLAN 200 while a desk port belongs only to VLAN 100. What should the network administrator implement first to meet this requirement?

  1. Assign deliberate root and secondary root bridge priorities for the relevant spanning-tree instances.
  2. Configure an 802.1Q trunk on the uplink and an access VLAN on the desk port.
  3. Mark and queue trusted voice traffic using a consistent switch QoS policy.
  4. Create SVIs with the VLAN interfaces present and enable supported Layer 3 routing.

Explanation

Correct Answer

B:

This action addresses the specific requirement because a trunk carries tagged VLANs while an access port normally assigns one untagged data VLAN. The independent acceptance check is: Traffic for both VLANs crosses the uplink and the desk device joins only VLAN 100.

Incorrect Answers

A:

This action addresses a different situation: A maintenance engineer sets two switches to claim root bridge priority and the campus topology becomes unstable. It would not directly resolve the current network requirement because a trunk carries tagged VLANs while an access port normally assigns one untagged data VLAN.

C:

This action addresses a different situation: A voice phone needs priority during a saturated trunk but VLAN tagging alone does not guarantee QoS. It would not directly resolve the current network requirement because a trunk carries tagged VLANs while an access port normally assigns one untagged data VLAN.

D:

This action addresses a different situation: A campus needs its access VLANs routed through SVIs on a multilayer switch. It would not directly resolve the current network requirement because a trunk carries tagged VLANs while an access port normally assigns one untagged data VLAN.

Question 435

A Wi-Fi AP reports 99% channel utilization from nearby networks despite few local associated clients. After the change, which result is most relevant to the original failure?

  1. Request traces show fewer round trips and lower end-to-end response time.
  2. Drop rates fall while legitimate peak traffic meets throughput goals.
  3. Both directions follow accepted firewall state and sessions remain stable under load.
  4. Airtime and retry metrics improve after the channel or interference source changes.

Explanation

Correct Answer

D:

The intended action is: Perform a wireless spectrum/site survey and choose appropriate channel placement. This works because non-Wi-Fi or neighboring WLAN activity can consume airtime without high local client count.

Incorrect Answers

A:

This choice would test a different networking condition: An application sees long delays despite low interface usage; WAN RTT is 170 ms and calls are synchronous and sequential. Its related action is: Reduce serial round trips using batching/caching or relocate a suitable dependency closer to callers.

B:

This choice would test a different networking condition: An ISP reports 1% packet loss only at peak traffic, and firewall drop queues spike at the same time. Its related action is: Determine whether queue congestion or capacity is the cause and adjust shaping or upgrade capacity.

C:

This choice would test a different networking condition: A website has low throughput only during asymmetric traffic across a stateful firewall pair. Its related action is: Correct return-path symmetry and state synchronization where required.

Question 436

An old router supports management over HTTP only and an attacker harvests its session cookie on the LAN. Which verification finding would support closing this network issue?

  1. The test rogue AP triggers a finding and cannot provide uncontrolled internal access.
  2. A spoofed SSID cannot authenticate as the corporate network to a properly configured client.
  3. A deliberately modified test packet fails integrity checks and is not accepted by the session.
  4. Captured network traffic contains no reusable management credentials after remediation.

Explanation

Correct Answer

D:

The intended action is: Remove insecure management interfaces and migrate to authenticated encrypted administration. This works because cleartext management exposes authentication material to nearby observers.

Incorrect Answers

A:

This choice would test a different networking condition: An office AP is deployed by a well-meaning employee without authorization and bypasses wireless policy. Its related action is: Detect and remove rogue wireless infrastructure through inventory and WIDS/WIPS monitoring.

B:

This choice would test a different networking condition: A public hotspot advertises the company SSID with stronger signal and users connect to the imposter. Its related action is: Detect evil-twin APs and enforce trusted enterprise authentication/server identity validation.

C:

This choice would test a different networking condition: A network packet capture shows a machine altering TCP packets between client and server despite no endpoint compromise. Its related action is: Treat it as an on-path attack and enforce mutual peer authentication and encrypted integrity-protected sessions.

Question 437

A campus default gateway VIP fails over but client ARP caches still point to the old hardware address. What acceptance result confirms the specified networking requirement is met?

  1. Multiple clients connect concurrently and the translation table shows distinct port mappings.
  2. After the active router fails, the VIP responds via the standby without DHCP changes.
  3. The advertised corporate prefix appears at approved peers and an unapproved prefix is rejected.
  4. Host traffic resumes using the virtual gateway after the controlled role switch.

Explanation

Correct Answer

D:

The intended action is: Validate FHRP virtual MAC behavior, gratuitous ARP and switch learning during failover. This works because gateway continuity requires layer-two forwarding to follow the newly active device.

Incorrect Answers

A:

This choice would test a different networking condition: An office has 250 inside clients but only one public IPv4 address for outbound browsing. Its related action is: Use PAT/NAT overload to distinguish simultaneous connections by translated source ports.

B:

This choice would test a different networking condition: Two routers provide a shared LAN default gateway but a single router outage forces manual host gateway changes. Its related action is: Use a first-hop redundancy protocol with a virtual IP and tracked master/active role.

C:

This choice would test a different networking condition: An organization connects to two internet providers and must exchange external route advertisements under explicit prefix policy. Its related action is: Use appropriately filtered eBGP peering and validate route acceptance and path preference.

Question 438

A guest Wi-Fi network and SCADA controller share the same broadcast domain to reduce switch configuration effort. Which verification finding would support closing this network issue?

  1. A valid assertion logs in to the correct app while a wrong-audience assertion is denied.
  2. Password-only access fails, and a properly authenticated contractor reaches only approved resources.
  3. A guest client cannot reach controller addresses while approved operational stations work.
  4. An uncredentialed person is denied and the attempt is captured by audit systems.

Explanation

Correct Answer

C:

The intended action is: Enforce strict separation between guest access and OT/ICS segments using network policy. This works because industrial control networks require boundaries that reflect safety and critical operations.

Incorrect Answers

A:

This choice would test a different networking condition: A client wants single sign-on to a hosted network controller using its corporate identity provider. Its related action is: Use an appropriate SAML federation flow with signed assertions and audience validation.

B:

This choice would test a different networking condition: A contractor uses one password to reach every remote network portal and a compromised password gives full access. Its related action is: Enforce MFA and least-privilege roles for network access, with targeted revocation.

D:

This choice would test a different networking condition: A physical data-center door relies on a painted sign that says 'authorized staff only'. Its related action is: Add enforceable locks and monitored access controls, supported by appropriate cameras.

Question 439

A floor's 6-GHz SSID is invisible to older 2.4/5-GHz-only client hardware. Which measured outcome provides the strongest evidence of success?

  1. A fake RADIUS endpoint is rejected and authorized network authentication succeeds.
  2. Guest devices reach the internet but cannot connect to internal servers.
  3. Legacy and modern clients connect on their supported bands under correct access policy.
  4. Roaming clients observe one SSID and distinct BSSIDs without unnecessary reconnections.

Explanation

Correct Answer

C:

The intended action is: Provide a compatible band/SSID for legacy clients instead of assuming all devices support 6 GHz. This works because 6-GHz operation requires radio support and applicable Wi-Fi security/regulatory capabilities.

Incorrect Answers

A:

This choice would test a different networking condition: A WPA2-Enterprise SSID uses a RADIUS certificate that clients do not validate. Its related action is: Enforce trusted server certificate validation in supplicants and correct RADIUS/EAP provisioning.

B:

This choice would test a different networking condition: A public guest SSID can reach internal printer and database networks. Its related action is: Isolate guest WLAN in its own routed security zone with deny-by-default access to internal subnets.

D:

This choice would test a different networking condition: Users walk between multiple APs with the same SSID but support mistakes the radio BSSID for the network name. Its related action is: Distinguish SSID network identity from per-radio BSSID and document the enterprise ESS design.

Question 440

A contractor needs browser-only access to a specific internal dashboard without a full routed VPN connection. Which verification finding would support closing this network issue?

  1. Approved hosts at both sites communicate after tunnel failover with no per-user VPN action.
  2. The contractor accesses only the dashboard and cannot scan internal subnet addresses.
  3. Operators reach a failed-router console while its production interfaces are disconnected.
  4. Managed operators connect through the jump host while unmanaged direct SSH is denied.

Explanation

Correct Answer

B:

The intended action is: Provide a clientless portal or application access gateway if the application supports it. This works because clientless remote access can publish selected web apps without generic network tunneling.

Incorrect Answers

A:

This choice would test a different networking condition: Two branch sites need permanent routed connectivity for application replication without end-user clients initiating VPN sessions. Its related action is: Establish a site-to-site VPN with matching crypto/authentication policies and routed networks.

C:

This choice would test a different networking condition: An engineer must access routers during a core IP outage, but the only management path uses the failed production network. Its related action is: Provide out-of-band management via independent console server or cellular path with strong access controls.

D:

This choice would test a different networking condition: A security team permits all administrators direct SSH from unmanaged laptops to every core router. Its related action is: Use a hardened jump host with MFA, role-based access and session logging.