McAfee-Secured Website

Exam Bundle

Exam Code: 200-301

Exam Name Cisco Certified Network Associate (CCNA)

Certification Provider: Cisco

Corresponding Certification: CCNA

Cisco 200-301 Bundle $44.99

100% Cisco 200-301 Guaranteed Success With Testking Training Materials

Get Real 200-301 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

  • Questions & Answers

    200-301 Questions & Answers

    760 Questions & Answers

    The ultimate exam preparation tool, Questions & Answers mirrors the actual 200-301 exam while allowing you to hone and measure every aspect of your test-taking ability.

  • 200-301 Video Course

    200-301 Video Course

    271 Video Lectures

    200-301 Video Course is developed by Cisco Professionals to help you pass the 200-301 exam.

    Description

    This course will improve your knowledge and skills required to pass Cisco Certified Network Associate (CCNA) exam.
  • Study Guide

    200-301 Study Guide

    1969 PDF Pages

    Developed by industry experts, this 1969-page guide spells out in painstaking detail all of the information you need to ace 200-301 exam.

Cisco Certified Network Associate (CCNA) (200-301) Practice Tests

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Total Cost: $194.97
Bundle Price: $149.98

Purchase Individually

  • Questions & Answers

    Questions & Answers

    760 Questions

    $124.99
  • 200-301 Video Course

    Video Course

    271 Video Lectures

    $39.99
  • Study Guide

    Study Guide

    1969 PDF Pages

    $29.99

Cisco 200-301 Practice Test 5

Question 40

A switch interface remains down after a server card is hard-set to an unsupported rate, while autonegotiation is disabled on the peer. What settings need attention?

  1. Inspect and correct a duplex mismatch between the Ethernet peers
  2. Match the link partners to a common supported speed and negotiation mode
  3. Verify path MTU and fragmentation or PMTUD behavior
  4. Inspect damaged cabling and physical signal integrity for CRC/FCS errors

Explanation

Correct Answer

B:

The ports must agree on a supported physical line rate and negotiation combination.

Incorrect Answers

A:

A duplex mismatch can degrade throughput on an established link, but the immediate problem here is a peer forced to a data rate that the other side cannot support.

C:

A path-MTU fault would affect oversized frames after link establishment. Here carrier does not form because link partner speed capabilities disagree.

D:

The stated failure follows an unsupported forced rate; checking physical cabling only becomes relevant if compatible speed/negotiation settings still cannot establish carrier.

Question 41

A freshly configured interface shows status administratively down even though its patch cable tests clean. Which action directly addresses this IOS state?

  1. Inspect damaged cabling and physical signal integrity for CRC/FCS errors
  2. Issue no shutdown on the administratively disabled interface
  3. Match the link partners to a common supported speed and negotiation mode
  4. Verify optical receive power, transceiver and fiber polarity

Explanation

Correct Answer

B:

Administratively down indicates that the interface has been disabled in configuration.

Incorrect Answers

A:

CRC counters diagnose corrupted frames on an operational link; an administratively disabled interface never reaches that traffic-checking stage.

C:

Changing the peer speed is unnecessary until this switch interface is enabled; `administratively down` is an explicit local configuration state.

D:

Optical power and polarity checks do not override an IOS interface configured with `shutdown`; enable it before physical-layer diagnostics.

Question 42

A fiber uplink is dark; receive power is absent at one side even though transceivers are seated. What should be tested first?

  1. Inspect and correct a duplex mismatch between the Ethernet peers
  2. Match the link partners to a common supported speed and negotiation mode
  3. Verify path MTU and fragmentation or PMTUD behavior
  4. Verify optical receive power, transceiver and fiber polarity

Explanation

Correct Answer

D:

Optical loss, wavelength compatibility and Tx/Rx paths must be verified on the fiber link.

Incorrect Answers

A:

Duplex mismatches concern Ethernet send/receive behavior after signal detection; absent received optical light points first to the optical path.

B:

Changing electrical link-negotiation settings will not restore missing receive light caused by incorrect fiber polarity, disconnected strands or incompatible optics.

C:

PMTUD depends on packets already traversing an established link; a dark fiber with no optical receive power cannot carry them.

Question 43

A port logs an unauthorized MAC address and then changes to err-disabled status under port security. What should be done before bringing it up?

  1. Inspect and correct a duplex mismatch between the Ethernet peers
  2. Verify path MTU and fragmentation or PMTUD behavior
  3. Verify available PoE budget and endpoint power requirements
  4. Identify and resolve the protection trigger before recovering an err-disabled port

Explanation

Correct Answer

D:

The port-security violation and recovery policy must be addressed, rather than blindly bouncing the port.

Incorrect Answers

A:

Duplex correction addresses a link-parameter mismatch, not the port-security event that explicitly put this access port into err-disabled status.

B:

An MTU change cannot reverse a security violation or restore an err-disabled switchport after an unauthorized MAC was detected.

C:

PoE power is unrelated to an err-disable trigger from port security; locate the violating MAC and policy before recovering the interface.

Question 44

Pings of 64 bytes pass but DF-set large packets across a tunnel fail consistently after encapsulation. What network parameter is suspect?

  1. Inspect damaged cabling and physical signal integrity for CRC/FCS errors
  2. Match the link partners to a common supported speed and negotiation mode
  3. Inspect and correct a duplex mismatch between the Ethernet peers
  4. Verify path MTU and fragmentation or PMTUD behavior

Explanation

Correct Answer

D:

Encapsulation can make the effective path MTU smaller than the original packet size.

Incorrect Answers

A:

FCS counters can indicate damaged media, but the critical discriminator is small packets succeeding while large DF-set packets fail only after tunnel encapsulation.

B:

Conflicting speeds normally affect carrier or general connectivity; packet-size-specific DF failure across an otherwise working tunnel points to effective MTU.

C:

A duplex mismatch causes loss/collisions across sizes. It does not naturally explain consistent failure only for DF-set packets exceeding the encapsulated path MTU.

Question 45

A new PoE camera has a link cable and negotiates data but will not power on; the switch reports insufficient power allocation. What should be checked?

  1. Verify path MTU and fragmentation or PMTUD behavior
  2. Issue no shutdown on the administratively disabled interface
  3. Inspect damaged cabling and physical signal integrity for CRC/FCS errors
  4. Verify available PoE budget and endpoint power requirements

Explanation

Correct Answer

D:

The switch power budget and camera power class must be compatible.

Incorrect Answers

A:

The camera cannot start because the switch reported an insufficient power grant; IP path MTU is not exercised before the endpoint powers up.

B:

The port negotiates Ethernet data but lacks sufficient PoE allocation. Administrative enabling is not the missing power-budget resource.

C:

Increasing CRC or FCS counters would suggest signal corruption; the observed switch power-budget alarm directly explains the camera startup failure.

Question 46

An access port displays many late collisions immediately after a speed/duplex change on only one peer. Which issue best matches the symptom?

  1. Inspect and correct a duplex mismatch between the Ethernet peers
  2. Verify path MTU and fragmentation or PMTUD behavior
  3. Issue no shutdown on the administratively disabled interface
  4. Verify available PoE budget and endpoint power requirements

Explanation

Correct Answer

A:

Late collisions strongly indicate a half-duplex segment experiencing a mismatch or excessive collision-domain issue.

Incorrect Answers

B:

A path-MTU problem would selectively affect large packets after a link comes up, not late collisions that immediately appeared when just one peer changed duplex.

C:

The interface exchanges traffic and records collisions, so `shutdown` is not the active condition to correct.

D:

PoE budget problems affect powered devices, whereas late Ethernet collisions after one-sided duplex reconfiguration indicate a mismatch.

Question 47

A data center uplink sees increasing CRC frames across one copper patch lead after an equipment move. What diagnostic direction is highest priority?

  1. Verify path MTU and fragmentation or PMTUD behavior
  2. Inspect damaged cabling and physical signal integrity for CRC/FCS errors
  3. Issue no shutdown on the administratively disabled interface
  4. Match the link partners to a common supported speed and negotiation mode

Explanation

Correct Answer

B:

Frame-check sequence corruption calls for inspecting the physical channel and connectors.

Incorrect Answers

A:

An MTU mismatch can impair large frames, but a sudden CRC increase isolated to one moved copper patch lead makes physical media/connectors the first isolation target.

C:

The link is up and counting CRC errors; a shutdown interface could not receive and tally those frames.

D:

Speed adjustment should follow observed negotiation mismatch; none is specified, while cable movement and physical CRC evidence are.

Question 48

A fiber interface reports receive signal below minimum optical threshold at the far switch. Which check is relevant?

  1. Verify optical receive power, transceiver and fiber polarity
  2. Verify available PoE budget and endpoint power requirements
  3. Inspect and correct a duplex mismatch between the Ethernet peers
  4. Verify path MTU and fragmentation or PMTUD behavior

Explanation

Correct Answer

A:

Low receive optical power points toward fiber attenuation, bad connectors, or a faulty optic.

Incorrect Answers

B:

PoE negotiation occurs over compatible copper Ethernet; this fiber link reports optical receive power below threshold, not insufficient endpoint power.

C:

A duplex mismatch normally concerns negotiated modes of an established Ethernet link; insufficient receive optical power must be resolved first.

D:

A path-MTU issue requires a functioning Layer 1 link and shows size-dependent loss, unlike low received light at the far optical transceiver.

Question 49

The interface line reports disabled by BPDU Guard after an unexpected switch was connected. What type of remediation is needed?

  1. Identify and resolve the protection trigger before recovering an err-disabled port
  2. Verify optical receive power, transceiver and fiber polarity
  3. Match the link partners to a common supported speed and negotiation mode
  4. Verify path MTU and fragmentation or PMTUD behavior

Explanation

Correct Answer

A:

A switch protection policy disabled the port and the root cause must be removed before recovery.

Incorrect Answers

B:

Fiber polarity cannot explain an explicit BPDU Guard err-disable log. The unexpected bridge advertisement must be removed or authorized before port recovery.

C:

Link speed negotiation is not the cause of a BPDU Guard protection action triggered by a connected switch.

D:

PMTUD is a Layer 3 packet-size mechanism. It does not clear a Layer 2 security error-disable caused by a BPDU arriving on an edge port.

Question 50

Two 1-Gbps-capable copper ports are manually set to conflicting speeds. No Ethernet carrier is established. What must change?

  1. Inspect and correct a duplex mismatch between the Ethernet peers
  2. Verify path MTU and fragmentation or PMTUD behavior
  3. Match the link partners to a common supported speed and negotiation mode
  4. Verify available PoE budget and endpoint power requirements

Explanation

Correct Answer

C:

The ports must communicate using mutually supported PHY speed and negotiation settings.

Incorrect Answers

A:

Duplex mismatch can reduce throughput on a live link; the two endpoints here fail to establish carrier because their forced data rates disagree.

B:

Packets never traverse this link, so changing the end-to-end maximum packet size cannot resolve the Layer 1 rate mismatch.

D:

PoE supplies endpoint electrical power, but the observed fault involves incompatible configured Ethernet speeds on powered ports.