McAfee-Secured Website

Exam Code: 156-315.82

Exam Name: Check Point Certified Security Expert - R82 (CCSE)

Certification Provider: Checkpoint

Corresponding Certification: CCSE R82

Questions & Answers

100% Checkpoint 156-315.82 Guaranteed Success With Testking Training Materials

Get Real 156-315.82 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

Questions & Answers

100 Questions & Answers with Testing Engine

"Check Point Certified Security Expert - R82 (CCSE) Exam", also known as 156-315.82 exam, is a Checkpoint certification exam.

Pass your tests with the always up-to-date 156-315.82 Exam Engine. Your 156-315.82 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Checkpoint 156-315.82 Practice Test 3

Question 20

An R82 replacement management server was installed and can access the network. The export archive copied successfully, but a license audit shows it was issued for the old appliance address. The import runbook requires license readiness first. Which validation tool should be used?

  1. Verify license state on the destination with cplic print
  2. Compare checksums of source and copied export files
  3. Invoke migrate_server import for the exported archive
  4. Connect with SmartConsole and inspect imported configuration

Explanation

Correct Answer

A:

Use cplic print on the destination and resolve any license mismatch before continuing the migration.

Incorrect Answers

B:

Checksum verification covers the archive bytes but not destination licensing.

C:

Running migrate_server import before checking the known license issue skips a documented prerequisite.

D:

Opening SmartConsole after import is too late to verify the pre-import license state.

Question 21

An operator images a second R82 appliance for an existing ElasticXL cluster and proposes running the Gaia First Time Configuration Wizard independently on the new member. The first member is already configured as SMO. What prevents duplicate initial cluster definitions?

  1. Allow the automatic image/configuration clone from SMO
  2. Use Gaia Portal Cluster Management > Pending Gateways
  3. Run Gaia First Time Configuration Wizard on the first appliance only
  4. Create one Single Management Object for the entire cluster

Explanation

Correct Answer

C:

Run the First Time Configuration Wizard only on the initial appliance and admit additional members through the cluster provisioning workflow.

Incorrect Answers

A:

Automatic cloning is the later result of admission, not a reason to run another initial wizard.

B:

The pending-member admission workflow follows the one-time first wizard; it does not justify a second one.

D:

Creating another Single Management Object contradicts the documented one-logical-gateway model for an ElasticXL cluster.

Question 22

After a management-link outage, both R82 Management Servers show Active in the HA status pane. Each has accepted changes while isolated. The owner has chosen which database to retain and captured the other changes. What HA action safely restores one Active and one Standby peer?

  1. Initiate changeover so a healthy standby becomes Active
  2. Initiate a manual synchronization between management peers
  3. Use Management HA actions to set one server to Standby
  4. Open the Management High Availability status in SmartConsole

Explanation

Correct Answer

C:

Use Management HA role actions to demote the selected peer; its database will be overwritten by the Active source during synchronization.

Incorrect Answers

A:

Initiating changeover assumes an orderly Active/Standby pair rather than an existing two-Active collision.

B:

A manual synchronization alone does not choose the authoritative Active node or resolve a two-Active HA collision.

D:

Viewing the status can confirm the collision but cannot correct the two Active roles.

Question 23

A security gateway must rewrite both the source address of a partner request and its destination address toward an internal server for one connection. Automatic object NAT does not express the combined translation criteria. Which NAT construction supports both changes?

  1. Use the Translated Services column in a Manual NAT rule
  2. Create a Manual NAT rule with both translated fields
  3. Create an appropriate one-direction Manual NAT policy rule
  4. Account for separate matching automatic source and destination rules

Explanation

Correct Answer

B:

One Manual NAT rule can specify translated source and translated destination fields for the same matching connection.

Incorrect Answers

A:

Changing only the translated destination service remaps ports, not both IP addresses.

C:

A one-direction-only rule by itself does not specify the required dual address translations.

D:

Relying solely on separate automatic rules may not express the combined manual match constraints.

Question 24

An R82 site-to-site peer negotiates an IPv6-only protected network over an IPv6 outer tunnel. A design review proposes IPv4 payload inside the IPv6 tunnel to reuse old selectors. The controls that address the separate requirement to resolve protected networks that never enter an established tunnel are already working as designed, and the change ticket must not disturb them. Which R82 action addresses the remaining symptom?

  1. Configure both gateways in the appropriate Site-to-Site VPN community
  2. Use the matching IPv6-in-IPv6 tunnel scheme and IKEv2
  3. Verify VPN domain definitions and encryption-domain selectors
  4. Review IKE negotiation settings and authentication on both peers

Explanation

Correct Answer

B:

R82 IPv6 VPN tunneling uses IPv6 within IPv6 and IKEv2. This directly addresses the documented incident evidence.

Incorrect Answers

A:

Site-to-Site communities define gateway membership and tunnel policy; this does not resolve the observed condition.

C:

VPN domains govern which networks are expected through the tunnel, but the current evidence calls for a different R82 operation.

D:

IKE agreement and authentication are prerequisites for tunnel setup, yet that applies to troubleshoot a VPN tunnel failing before security associations form rather than the observed issue.

Question 25

A security analyst modifies a SmartEvent custom detection filter, saves it, and then sees incoming logs still evaluated by the previous version. The gateway Access Control policy is unchanged. Which installation action is needed to make the revised detection policy active?

  1. Configure a SmartEvent threshold of log count and seconds
  2. Assign an Automatic Reaction to its event definition
  3. Open Logs & Events and select Views
  4. Save changes and Install Event Policy

Explanation

Correct Answer

D:

Save and install the SmartEvent Event Policy after the definition change; saving alone does not activate the new correlation policy.

Incorrect Answers

A:

Changing a threshold again does not deploy the already edited event definition.

B:

An automatic reaction does not install the revised detection criteria.

C:

Opening Views only displays events and does not deploy event policy.

Question 26

A gateway is scheduled for a major R82 upgrade. The change owner has confirmed the supported path but has not captured recoverable system state or checked disk prerequisites. What is the appropriate preparation before starting any upgrade package?

  1. Use Central Deployment Version Upgrade to Specific Major Version
  2. Use the Version Upgrade action on the selected gateway
  3. Back up the appliance and confirm the target package is supported
  4. Review the package installation and gateway version result

Explanation

Correct Answer

C:

Take an appropriate appliance backup or snapshot and confirm prerequisites before installing the upgrade.

Incorrect Answers

A:

Selecting a major-version action without a rollback baseline ignores the required recovery protection.

B:

Starting the version change first is premature while backup and disk checks are outstanding.

D:

Post-upgrade package verification does not protect the current state before the change.

Question 27

The new R82 Management Server successfully imported its database and will assume the old server’s management role. The old source host still has its network connections active, and both could respond as the controlling manager. What cutover safeguard comes next?

  1. Connect the new management host on the intended network
  2. Connect with SmartConsole and inspect imported configuration
  3. Plan control-plane addressing and reconnect managed gateways correctly
  4. Disconnect the retired source before activating its replacement

Explanation

Correct Answer

D:

Disconnect or retire the original source server before activating the new management host, avoiding competing management identities.

Incorrect Answers

A:

Connecting the new server while the old one is active can create duplicate control-plane identities.

B:

Validating the imported objects does not isolate the duplicate active management endpoint.

C:

Address planning alone does not remove the old host from the network.

Question 28

An additional powered-on appliance has the proper Sync connection and is visible under Pending Gateways in Gaia Portal. The current ElasticXL site needs more capacity, not a separate recovery site. Which operator action admits the member without a second site?

  1. Create a new Site while admitting the pending appliance
  2. Add the pending appliance to the existing Site
  3. Use Gaia Portal Cluster Management > Pending Gateways
  4. Run show cluster info provision in Gaia gClish

Explanation

Correct Answer

C:

Select the appliance in Pending Gateways and add it to the existing ElasticXL Site to scale current capacity.

Incorrect Answers

A:

Creating a new site changes the resilience topology rather than increasing this existing site capacity.

B:

An unscoped capacity action does not specify the pending appliance already discovered.

D:

A CLI discovery inspection alone does not admit the appliance to the chosen site.

Question 29

Two management servers each became Active during a link failure. An administrator proposes clicking Set Standby immediately on one node, but it holds unpublished rule changes absent from the other peer. What should the change owner establish before any demotion?

  1. Use Management HA actions to set one server to Standby
  2. Review which database will be overwritten when setting Standby
  3. Initiate a manual synchronization between management peers
  4. Initiate changeover so a healthy standby becomes Active

Explanation

Correct Answer

B:

Determine which database will survive and preserve useful unique work: demoting a peer overwrites its local management data.

Incorrect Answers

A:

Setting Standby before protecting divergent changes can irreversibly discard its database content.

C:

A manual sync is not a safe substitute for choosing the authoritative data in collision mode.

D:

An ordinary changeover does not reconcile different unpublished edits held independently by two Active management nodes.

Question 30

An Access Control rule refers to an Updatable Object representing a cloud provider. A provider adds addresses overnight and the gateway updates its membership without a SmartConsole policy-install task. Why should operators not schedule a reinstall for every address change?

  1. Let the Updatable Object update on the Security Gateway
  2. Use an Updatable Object based on the service address feed
  3. Reference the object directly in eligible policy rule columns
  4. Publish the session and install the relevant security policy

Explanation

Correct Answer

A:

The gateway refreshes membership from published lists automatically; normal feed changes do not require a new policy installation.

Incorrect Answers

B:

Creating a new service object for each provider update defeats the Updatable Object mechanism.

C:

Using eligible policy columns is required initially, but does not explain per-update installation behavior.

D:

An additional unchanged policy install is not the membership-refresh mechanism.

Check Point Certified Security Expert - R82 (CCSE) (156-315.82) Practice Tests