McAfee-Secured Website

Exam Bundle

Exam Code: N10-009

Exam Name CompTIA Network+

Certification Provider: CompTIA

Corresponding Certification: CompTIA Network+

CompTIA N10-009 Bundle $44.99

100% CompTIA N10-009 Guaranteed Success With Testking Training Materials

Get Real N10-009 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

  • Questions & Answers

    N10-009 Questions & Answers

    768 Questions & Answers

    The ultimate exam preparation tool, Questions & Answers mirrors the actual N10-009 exam while allowing you to hone and measure every aspect of your test-taking ability.

  • N10-009 Video Course

    N10-009 Video Course

    240 Video Lectures

    N10-009 Video Course is developed by CompTIA Professionals to help you pass the N10-009 exam.

    Description

    This course will improve your knowledge and skills required to pass CompTIA Network+ exam.
  • Study Guide

    N10-009 Study Guide

    128 PDF Pages

    Developed by industry experts, this 128-page guide spells out in painstaking detail all of the information you need to ace N10-009 exam.

CompTIA Network+ (N10-009) Practice Tests

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Total Cost: $194.97
Bundle Price: $149.98

Purchase Individually

  • Questions & Answers

    Questions & Answers

    768 Questions

    $124.99
  • N10-009 Video Course

    Video Course

    240 Video Lectures

    $39.99
  • Study Guide

    Study Guide

    128 PDF Pages

    $29.99

CompTIA N10-009 Practice Test 49

Question 480

A switch receives a flood of source MAC addresses and its forwarding table begins punting traffic unexpectedly. Which recommendation most directly resolves the documented network issue?

  1. Apply anti-tailgating procedures with badge challenge and controlled visitor escort.
  2. Investigate MAC flooding and apply appropriate port-security limits and monitoring.
  3. Limit trunking/native VLAN exposure and validate access-port VLAN hopping protections.
  4. Recognize phishing, report it through the approved channel and verify the request out of band.

Explanation

Correct Answer

B:

This action addresses the specific requirement because cAM exhaustion may cause unwanted flooding or forwarding instability. The independent acceptance check is: MAC table occupancy remains bounded and test clients cannot induce widespread unknown-unicast flooding.

Incorrect Answers

A:

This action addresses a different situation: An unknown person follows an employee through a locked server-room door while carrying a fake delivery package. It would not directly resolve the current network requirement because cAM exhaustion may cause unwanted flooding or forwarding instability.

C:

This action addresses a different situation: A compromised switch trunk sends double-tagged frames designed to cross an unintended VLAN boundary. It would not directly resolve the current network requirement because cAM exhaustion may cause unwanted flooding or forwarding instability.

D:

This action addresses a different situation: An employee receives an email urging immediate VPN password verification through an unfamiliar link. It would not directly resolve the current network requirement because cAM exhaustion may cause unwanted flooding or forwarding instability.

Question 481

An incident team has inconclusive packet captures and no permission to change a provider router. What is the most appropriate network configuration or troubleshooting action for this requirement?

  1. Escalate with gathered evidence, clear affected scope and measured timestamps to the authorized owner.
  2. Apply a targeted rule correction and verify both service functionality and security controls.
  3. Establish and test plausible causes from the smallest impacted scope before replacing shared infrastructure.
  4. Implement the validated VLAN correction through approved change process and retest the original symptom.

Explanation

Correct Answer

A:

This action addresses the specific requirement because unconfirmed theories and absent authority require an evidence-rich escalation, not unauthorized reconfiguration. The independent acceptance check is: Provider staff can reproduce the fault using the supplied path and counters.

Incorrect Answers

B:

This action addresses a different situation: An engineer fixes lost connectivity by disabling the security ACL but never restores the intended protections. It would not directly resolve the current network requirement because unconfirmed theories and absent authority require an evidence-rich escalation, not unauthorized reconfiguration.

C:

This action addresses a different situation: A technician immediately replaces the core switch after one laptop fails to load a website. It would not directly resolve the current network requirement because unconfirmed theories and absent authority require an evidence-rich escalation, not unauthorized reconfiguration.

D:

This action addresses a different situation: A technician confirms an incorrect VLAN assignment but plans to keep testing DNS without correcting the known defect. It would not directly resolve the current network requirement because unconfirmed theories and absent authority require an evidence-rich escalation, not unauthorized reconfiguration.

Question 482

An employee reports intermittent ethernet while a switch shows frequent link-up/link-down events on that one port. What acceptance result confirms the specified networking requirement is met?

  1. A certification test passes the correct category limits for the final compliant run.
  2. Repeated door operation no longer changes link state or error counters.
  3. Link flaps stop with the faulty connector replaced and routing stays unchanged.
  4. Return loss and interface errors meet the approved optical acceptance targets.

Explanation

Correct Answer

C:

The intended action is: Inspect patch cord, jack and NIC connector before changing routing policies. This works because repeated local PHY state transitions suggest a physical/interface defect.

Incorrect Answers

A:

This choice would test a different networking condition: A 110-meter permanent copper run repeatedly fails 1-Gbps certification. Its related action is: Shorten/restructure the horizontal link or add a compliant active distribution point.

B:

This choice would test a different networking condition: A building cable passes continuity but gives intermittent link loss whenever a door closes on the cable. Its related action is: Correct the mechanical pinch and replace damaged cable while preserving bend radius.

D:

This choice would test a different networking condition: A fiber patch has acceptable insertion loss but high optical return loss due to a damaged polished end. Its related action is: Repair or replace the defective connector and verify return-loss specifications.

Question 483

An emergency routing fix is technically successful but has no documented approval or follow-up review. What observation most directly validates the chosen network solution?

  1. Reviewers can reconstruct the exact config diff, recovery reasoning and final approval.
  2. An independent technician traces the affected patch using the documentation without trial-and-error unplugging.
  3. New address requests are allocated uniquely and conflict checks find the previously duplicated IP.
  4. A configuration diff traces each priority change to an approved request and tested result.

Explanation

Correct Answer

A:

The intended action is: Record an emergency change with risk justification, monitoring and retrospective approval. This works because emergency response does not eliminate governance and incident traceability.

Incorrect Answers

B:

This choice would test a different networking condition: A field technician patches a fiber port but the logical topology shows no rack location or cable ID for the link. Its related action is: Maintain physical rack/cable maps alongside logical Layer 2 and Layer 3 diagrams.

C:

This choice would test a different networking condition: A branch uses spreadsheet IP assignments and accidentally duplicates addresses across two teams. Its related action is: Implement IP address management with authoritative allocations, reservations and change control.

D:

This choice would test a different networking condition: An engineer changes switch spanning-tree priorities through a personal script without a ticket or peer review. Its related action is: Route configuration changes through controlled approvals, versioned baselines and audit records.

Question 484

An ISP reports 1% packet loss only at peak traffic, and firewall drop queues spike at the same time. Which post-change test best demonstrates that the problem is resolved?

  1. Failed node is removed from new requests and distribution matches the intended algorithm.
  2. Drop rates fall while legitimate peak traffic meets throughput goals.
  3. Throughput and queue-drop counters improve after addressing the 50-Mbps uplink constraint.
  4. Continuous application tests survive floor transitions with acceptable roam delay.

Explanation

Correct Answer

B:

The intended action is: Determine whether queue congestion or capacity is the cause and adjust shaping or upgrade capacity. This works because congestion-driven drops are load-dependent rather than a constant physical-layer fault.

Incorrect Answers

A:

This choice would test a different networking condition: A load balancer shows 40,000 connections to one unhealthy pool member while three other nodes are idle. Its related action is: Fix health probes and distribution policies so unhealthy servers are excluded.

C:

This choice would test a different networking condition: A branch has 1-Gbps access but its 50-Mbps carrier uplink is saturated each afternoon. Its related action is: Measure the true bottleneck and manage utilization or upgrade carrier capacity.

D:

This choice would test a different networking condition: A wireless client roams but disconnects every time it crosses between floors with unmatched encryption policies. Its related action is: Align roaming SSID security profiles and validate the authentication/transition design.

Question 485

A transceiver indicates low optical receive power and a dusty LC end face is visible. Which post-change test best demonstrates that the problem is resolved?

  1. Optical levels return inside specification with stable error counters.
  2. Return loss and interface errors meet the approved optical acceptance targets.
  3. Link flaps stop with the faulty connector replaced and routing stays unchanged.
  4. The repaired link's trace shows the previous event reduced below acceptance limits.

Explanation

Correct Answer

A:

The intended action is: Clean and inspect the fiber end face with approved tools, then measure optical power. This works because contamination can increase insertion loss and reduce link margin.

Incorrect Answers

B:

This choice would test a different networking condition: A fiber patch has acceptable insertion loss but high optical return loss due to a damaged polished end. Its related action is: Repair or replace the defective connector and verify return-loss specifications.

C:

This choice would test a different networking condition: An employee reports intermittent ethernet while a switch shows frequent link-up/link-down events on that one port. Its related action is: Inspect patch cord, jack and NIC connector before changing routing policies.

D:

This choice would test a different networking condition: A fiber OTDR trace shows a large reflection at a newly installed mechanical connector. Its related action is: Inspect and repair the event at the measured OTDR distance.

Question 486

A web security gateway blocks domains by DNS name but some risky traffic uses IP literals or alternate URLs. What should the network administrator implement first to meet this requirement?

  1. Restrict management sources and replace weak community access with SNMPv3 where supported.
  2. Combine URL filtering, content controls and endpoint policy suitable for the application.
  3. Segment IoT/OT and general IT systems into enforced trust zones with monitored permitted flows.
  4. Implement a least-privilege ACL with explicit required flows and deny-by-default for others.

Explanation

Correct Answer

B:

This action addresses the specific requirement because simple hostname blocks alone may not cover all web request paths. The independent acceptance check is: Controlled prohibited content is blocked through tested request variations without breaking approved sites.

Incorrect Answers

A:

This action addresses a different situation: Network technicians use SNMPv2c 'public' and permit remote configuration from any VLAN. It would not directly resolve the current network requirement because simple hostname blocks alone may not cover all web request paths.

C:

This action addresses a different situation: A manufacturing site puts cameras, industrial controllers, and office laptops on one Layer 2 broadcast domain. It would not directly resolve the current network requirement because simple hostname blocks alone may not cover all web request paths.

D:

This action addresses a different situation: A firewall allows all traffic from guest networks into the internal finance subnet. It would not directly resolve the current network requirement because simple hostname blocks alone may not cover all web request paths.

Question 487

A newly built office runs network cabling through a shared ventilation plenum without checking fire ratings. What observation most directly validates the chosen network solution?

  1. Both interfaces negotiate the supported rate and remain error-free under load.
  2. End-to-end strand mapping follows the approved polarity plan and every intended lane links.
  3. A wiremap tester reports correct pairs and the Ethernet link negotiates expected speed.
  4. Inspection approves the installed cable class in each air-handling pathway.

Explanation

Correct Answer

D:

The intended action is: Use locally code-compliant plenum-rated cable or approved conduit methods for the air-handling space. This works because cable jacket fire/smoke ratings depend on installation environment and local code.

Incorrect Answers

A:

This choice would test a different networking condition: A short data-center connection between top-of-rack switches uses compatible high-speed ports and needs low-cost short reach. Its related action is: Evaluate qualified direct-attach copper (twinax DAC) rather than long-distance optical modules.

B:

This choice would test a different networking condition: A data hall needs many parallel fiber strands terminated in a high-density trunk rather than individual LC connectors. Its related action is: Specify MPO/MTP-compatible multifiber assemblies with correct polarity and mating requirements.

C:

This choice would test a different networking condition: A desk switch has RJ45 jacks but the installer presents RJ11 telephone plugs and intermittent contact. Its related action is: Terminate twisted-pair Ethernet with supported RJ45 modular connectors and tested pair mapping.

Question 488

An operator wants to inspect DHCP and TLS packets on a permitted lab interface to explain a failed handshake. What is the most appropriate network configuration or troubleshooting action for this requirement?

  1. Use traceroute/tracert and corroborating router path information.
  2. Check ARP/neighbor cache and correlate MAC learning information on the switch.
  3. Capture the traffic with Wireshark or tcpdump using a scoped capture filter.
  4. Use an authorized Wi-Fi analyzer to survey channels, RSSI and utilization.

Explanation

Correct Answer

C:

This action addresses the specific requirement because protocol analyzers expose real packet exchanges and negotiation failures. The independent acceptance check is: The capture shows the relevant offer or handshake sequence without collecting unrelated user data.

Incorrect Answers

A:

This action addresses a different situation: A remote application fails across several routers and an engineer needs to locate the first hop where the path changes. It would not directly resolve the current network requirement because protocol analyzers expose real packet exchanges and negotiation failures.

B:

This action addresses a different situation: A local switch may have the wrong MAC neighbor associated with a duplicate IPv4 address. It would not directly resolve the current network requirement because protocol analyzers expose real packet exchanges and negotiation failures.

D:

This action addresses a different situation: A Wi-Fi team needs to locate nearby co-channel APs and compare signal strength across meeting rooms. It would not directly resolve the current network requirement because protocol analyzers expose real packet exchanges and negotiation failures.

Question 489

Two sites run OSPF and a new neighbor remains in an INIT state because the two routers use incompatible hello timers. Select the most defensible networking decision for this case.

  1. Align OSPF interface parameters required for adjacency, including hello and dead intervals.
  2. Configure a precise static destination route with the least broad valid prefix and next hop.
  3. Apply outbound BGP prefix filters and validation tied to approved announcements.
  4. Configure matching tagged subinterfaces and appropriate per-VLAN IP gateways.

Explanation

Correct Answer

A:

This action addresses the specific requirement because mismatched required OSPF neighbor parameters can prevent a full adjacency. The independent acceptance check is: Both neighbors reach FULL and the expected OSPF routes enter the table.

Incorrect Answers

B:

This action addresses a different situation: A transit router needs an explicit route for a small remote network but the proposed solution advertises every internal prefix globally. It would not directly resolve the current network requirement because mismatched required OSPF neighbor parameters can prevent a full adjacency.

C:

This action addresses a different situation: A network advertises 192.0.2.0/24 from one BGP edge despite having no authorized ownership of that prefix. It would not directly resolve the current network requirement because mismatched required OSPF neighbor parameters can prevent a full adjacency.

D:

This action addresses a different situation: A router has subinterfaces for VLANs 10 and 20 over one 802.1Q tagged uplink. It would not directly resolve the current network requirement because mismatched required OSPF neighbor parameters can prevent a full adjacency.

Question 490

A traffic analysis dashboard reports byte totals but cannot determine which conversation drives congestion. Which verification finding would support closing this network issue?

  1. The high-volume talker is identifiable by flow endpoints and byte counts during a test.
  2. Pulling the test cable generates a timestamped trap with correct device and interface details.
  3. A test unauthorized rule yields an attributable drift finding and remediation record.
  4. The dashboard captures p99 spikes with corresponding interface congestion markers.

Explanation

Correct Answer

A:

The intended action is: Collect suitable flow telemetry such as NetFlow/IPFIX with source, destination and interface attributes. This works because flow records summarize conversations without requiring full payload capture.

Incorrect Answers

B:

This choice would test a different networking condition: A monitoring team wants immediate notification of a switch uplink failure instead of waiting five minutes for counter polling. Its related action is: Configure and test SNMP traps or informs to the designated manager.

C:

This choice would test a different networking condition: A nightly automated configuration job changes firewall rules but the NOC has no policy drift detection. Its related action is: Compare running configurations against reviewed baselines and alert on unapproved diffs.

D:

This choice would test a different networking condition: A NOC monitors average bandwidth but users report 99th-percentile call latency spikes every afternoon. Its related action is: Add latency, jitter, loss and tail-percentile application indicators to performance monitoring.